diff --git a/devicetypes/adf/fibaro-roller-shutter.src/fibaro-roller-shutter.groovy b/devicetypes/adf/fibaro-roller-shutter.src/fibaro-roller-shutter.groovy
new file mode 100644
index 0000000..34bd53d
--- /dev/null
+++ b/devicetypes/adf/fibaro-roller-shutter.src/fibaro-roller-shutter.groovy
@@ -0,0 +1,345 @@
+/**
+ * Device Type Definition File
+ *
+ * Device Type: Fibaro Roller Shutter
+ * File Name: fibaro-roller-shutter.groovy
+ * Initial Release: 2015-06-00
+ * Author: SmartThings
+ *
+ * Copyright 2015 SmartThings
+ *
+ * Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ * in compliance with the License. You may obtain a copy of the License at:
+ *
+ * http://www.apache.org/licenses/LICENSE-2.0
+ *
+ * Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ * on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ * for the specific language governing permissions and limitations under the License.
+ *
+ */
+
+metadata {
+ // Automatically generated. Make future change here.
+ definition (name: "Fibaro Roller Shutter", namespace: "ADF", author: "ADF") {
+ capability "Switch Level"
+ capability "Actuator"
+ capability "Switch"
+ capability "Polling"
+ capability "Refresh"
+ capability "Sensor"
+
+ command "resetParams2StDefaults"
+ command "listCurrentParams"
+ command "updateZwaveParam"
+
+ fingerprint deviceId: "0x1101", inClusters: "0x72,0x86,0x70,0x85,0x8E,0x26,0x7A,0x27,0x73,0xEF,0x26,0x2B"
+ }
+
+ simulator {
+ status "on": "command: 2003, payload: FF"
+ status "off": "command: 2003, payload: 00"
+ status "09%": "command: 2003, payload: 09"
+ status "10%": "command: 2003, payload: 0A"
+ status "33%": "command: 2003, payload: 21"
+ status "66%": "command: 2003, payload: 42"
+ status "99%": "command: 2003, payload: 63"
+
+ // reply messages
+ reply "2001FF,delay 5000,2602": "command: 2603, payload: FF"
+ reply "200100,delay 5000,2602": "command: 2603, payload: 00"
+ reply "200119,delay 5000,2602": "command: 2603, payload: 19"
+ reply "200132,delay 5000,2602": "command: 2603, payload: 32"
+ reply "20014B,delay 5000,2602": "command: 2603, payload: 4B"
+ reply "200163,delay 5000,2602": "command: 2603, payload: 63"
+ }
+
+ tiles {
+ multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true) {
+ tileAttribute("device.switch", key: "PRIMARY_CONTROL") {
+ attributeState("on", label:"open", action:"switch.off", icon:"st.doors.garage.garage-open", backgroundColor:"#79b821", nextState: "turningOff")
+ attributeState("off", label:"close", action:"switch.on", icon:"st.doors.garage.garage-closed", backgroundColor:"#ffffff", nextState: "turningOn")
+ attributeState("turningOn", label:"opening", action:"switch.off", icon:"st.doors.garage.garage-opening", backgroundColor:"#79b821", nextState: "turningOff")
+ attributeState("turningOff", label:"closing", action:"switch.on", icon:"st.doors.garage.garage-closing", backgroundColor:"#ffffff", nextState:"turningOn")
+ }
+ tileAttribute ("device.level", key: "SLIDER_CONTROL") {
+ attributeState("level", action:"switch level.setLevel")
+ }
+ }
+ standardTile("refresh", "device.switch", width: 2, height: 2, inactiveLabel: false, decoration: "flat") {
+ state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
+ }
+ standardTile("on", "device.switch", width: 2, height: 2, inactiveLabel: false, decoration: "flat") {
+ state("on", label:'open', action:"switch.on", icon:"st.doors.garage.garage-opening")
+ }
+ standardTile("off", "device.switch", width: 2, height: 2, inactiveLabel: false, decoration: "flat") {
+ state("off", label:'close', action:"switch.off", icon:"st.doors.garage.garage-closing")
+ }
+ standardTile("stop", "device.level", width: 2, height: 2, inactiveLabel: false, decoration: "flat") {
+ state("default", label:'stop/my', action:"switch level.setLevel", icon:"st.Transportation.transportation13")
+ }
+
+ main(["switch"])
+ details(["switch", "refresh", "on", "off", "stop"])
+ }
+}
+
+def parse(String description) {
+ def item1 = [
+ canBeCurrentState: false,
+ linkText: getLinkText(device),
+ isStateChange: false,
+ displayed: false,
+ descriptionText: description,
+ value: description
+ ]
+ def result
+ def cmd = zwave.parse(description, [0x26: 1, 0x70: 2, 072: 2])
+ //log.debug "cmd: ${cmd}"
+
+ if (cmd) {
+ result = createEvent(cmd, item1)
+ }
+ else {
+ item1.displayed = displayed(description, item1.isStateChange)
+ result = [item1]
+ }
+
+ if(result?.descriptionText)
+ log.debug "Parse returned ${result?.descriptionText}"
+
+ result
+
+}
+
+def createEvent(physicalgraph.zwave.commands.basicv1.BasicReport cmd, Map item1) {
+ def result = doCreateEvent(cmd, item1)
+ for (int i = 0; i < result.size(); i++) {
+ result[i].type = "physical"
+ }
+ result
+}
+
+def createEvent(physicalgraph.zwave.commands.basicv1.BasicSet cmd, Map item1) {
+ def result = doCreateEvent(cmd, item1)
+ for (int i = 0; i < result.size(); i++) {
+ result[i].type = "physical"
+ }
+ result
+}
+
+def createEvent(physicalgraph.zwave.commands.switchmultilevelv1.SwitchMultilevelStartLevelChange cmd, Map item1) {
+ []
+}
+
+def createEvent(physicalgraph.zwave.commands.switchmultilevelv1.SwitchMultilevelStopLevelChange cmd, Map item1) {
+ [response(zwave.basicV1.basicGet())]
+}
+
+def createEvent(physicalgraph.zwave.commands.switchmultilevelv1.SwitchMultilevelSet cmd, Map item1) {
+ def result = doCreateEvent(cmd, item1)
+ for (int i = 0; i < result.size(); i++) {
+ result[i].type = "physical"
+ }
+ result
+}
+
+def createEvent(physicalgraph.zwave.commands.switchmultilevelv1.SwitchMultilevelReport cmd, Map item1) {
+ def result = doCreateEvent(cmd, item1)
+ result[0].descriptionText = "${item1.linkText} is ${item1.value}"
+ result[0].handlerName = cmd.value ? "statusOn" : "statusOff"
+ for (int i = 0; i < result.size(); i++) {
+ result[i].type = "digital"
+ }
+ result
+}
+
+def doCreateEvent(physicalgraph.zwave.Command cmd, Map item1) {
+ def result = [item1]
+
+ item1.name = "switch"
+ item1.value = cmd.value ? "on" : "off"
+ item1.handlerName = item1.value
+ item1.descriptionText = "${item1.linkText} was turned ${item1.value}"
+ item1.canBeCurrentState = true
+ item1.isStateChange = isStateChange(device, item1.name, item1.value)
+ item1.displayed = item1.isStateChange
+
+ if (cmd.value >= 5) {
+ def item2 = new LinkedHashMap(item1)
+ item2.name = "level"
+ item2.value = cmd.value as String
+ item2.unit = "%"
+ item2.descriptionText = "${item1.linkText} dimmed ${item2.value} %"
+ item2.canBeCurrentState = true
+ item2.isStateChange = isStateChange(device, item2.name, item2.value)
+ item2.displayed = false
+ result << item2
+ }
+ result
+}
+
+def createEvent(physicalgraph.zwave.Command cmd, Map map) {
+ // Handles any Z-Wave commands we aren't interested in
+ log.debug "UNHANDLED COMMAND $cmd"
+}
+
+def on() {
+ log.info "on"
+ delayBetween([zwave.basicV1.basicSet(value: 0xFF).format(), zwave.switchMultilevelV1.switchMultilevelGet().format()], 5000)
+}
+
+def off() {
+ delayBetween ([zwave.basicV1.basicSet(value: 0x00).format(), zwave.switchMultilevelV1.switchMultilevelGet().format()], 5000)
+}
+
+def setLevel(value) {
+ def level = Math.min(value as Integer, 99)
+ delayBetween ([zwave.basicV1.basicSet(value: level).format(), zwave.switchMultilevelV1.switchMultilevelGet().format()], 5000)
+}
+
+def setLevel(value, duration) {
+ def level = Math.min(value as Integer, 99)
+ def dimmingDuration = duration < 128 ? duration : 128 + Math.round(duration / 60)
+ zwave.switchMultilevelV2.switchMultilevelSet(value: level, dimmingDuration: dimmingDuration).format()
+}
+
+def poll() {
+ zwave.switchMultilevelV1.switchMultilevelGet().format()
+}
+
+def refresh() {
+ zwave.switchMultilevelV1.switchMultilevelGet().format()
+}
+
+ /**
+ * Configures the device to settings needed by SmarthThings at device discovery time. Assumes
+ * device is already at default parameter settings.
+ *
+ * @param none
+ *
+ * @return none
+ */
+def configure() {
+ log.debug "Configuring Device..."
+ def cmds = []
+
+ // send associate to group 3 to get sensor data reported only to hub
+ cmds << zwave.associationV2.associationSet(groupingIdentifier:3, nodeId:[zwaveHubNodeId]).format()
+
+
+ delayBetween(cmds, 500)
+}
+
+
+def createEvent(physicalgraph.zwave.commands.configurationv2.ConfigurationReport cmd, Map item1) {
+
+ log.debug "${device.displayName} parameter '${cmd.parameterNumber}' with a byte size of '${cmd.size}' is set to '${cmd.configurationValue}'"
+
+}
+
+ /**
+ * This method will allow the user to update device parameters (behavior) from an app.
+ * the user can write his/her own app to envoke this method.
+ * No type or value checking is done to compare to what device capability or reaction.
+ * It is up to user to read OEM documentation prio to envoking this method.
+ *
+ * THIS IS AN ADVANCED OPERATION. USE AT YOUR OWN RISK! READ OEM DOCUMENTATION!
+ *
+ * @param List[paramNumber:80,value:10,size:1]
+ *
+ *
+ * @return none
+ */
+def updateZwaveParam(params) {
+ if ( params ) {
+ def pNumber = params.paramNumber
+ def pSize = params.size
+ def pValue = [params.value]
+ log.debug "Make sure device is awake and in recieve mode"
+ log.debug "Updating ${device.displayName} parameter number '${pNumber}' with value '${pValue}' with size of '${pSize}'"
+
+ def cmds = []
+ cmds << zwave.configurationV1.configurationSet(configurationValue: pValue, parameterNumber: pNumber, size: pSize).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: pNumber).format()
+ delayBetween(cmds, 1000)
+ }
+}
+
+ /**
+ * Sets all of available Fibaro parameters back to the device defaults except for what
+ * SmartThings needs to support the stock functionality as released.
+ *
+ *
THIS IS AN ADVANCED OPERATION. USE AT YOUR OWN RISK! READ OEM DOCUMENTATION!
+ *
+ * @param none
+ *
+ * @return none
+ */
+def resetParams2StDefaults() {
+ log.debug "Resetting ${device.displayName} parameters to SmartThings compatible defaults"
+ def cmds = []
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [255], parameterNumber: 1, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [0], parameterNumber: 6, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [1], parameterNumber: 7, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [1], parameterNumber: 8, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [5], parameterNumber: 9, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [1], parameterNumber: 10, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [1], parameterNumber: 11, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [99], parameterNumber: 12, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [2], parameterNumber: 13, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [0], parameterNumber: 14, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [1], parameterNumber: 15, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [1], parameterNumber: 16, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [0], parameterNumber: 17, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [0], parameterNumber: 18, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [0], parameterNumber: 19, size: 1).format()
+ //Param 20 is different for 50Hz or 60 Hz uncomment the line that will reflect the power frequency used
+ //cmds << zwave.configurationV1.configurationSet(configurationValue: [101], parameterNumber: 20, size: 1).format() //60 Hz (US)
+ //cmds << zwave.configurationV1.configurationSet(configurationValue: [110], parameterNumber: 20, size: 1).format() //50 Hz (UK)
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [3], parameterNumber: 30, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [600], parameterNumber: 39, size: 1).format()
+ //Param 40 not needed by SmartThings
+ //cmds << zwave.configurationV1.configurationSet(configurationValue: [0], parameterNumber: 40, size: 1).format()
+ cmds << zwave.configurationV1.configurationSet(configurationValue: [0], parameterNumber: 41, size: 1).format()
+
+ delayBetween(cmds, 500)
+}
+
+ /**
+ * Lists all of available Fibaro parameters and thier current settings out to the
+ * logging window in the IDE. This will be called from the "Fibaro Tweaker" or
+ * user's own app.
+ *
+ *
THIS IS AN ADVANCED OPERATION. USE AT YOUR OWN RISK! READ OEM DOCUMENTATION!
+ *
+ * @param none
+ *
+ * @return none
+ */
+def listCurrentParams() {
+ log.debug "Listing of current parameter settings of ${device.displayName}"
+ def cmds = []
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 1).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 6).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 7).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 8).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 9).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 10).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 11).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 12).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 13).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 14).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 15).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 16).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 17).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 18).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 19).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 20).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 30).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 39).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 40).format()
+ cmds << zwave.configurationV1.configurationGet(parameterNumber: 41).format()
+
+ delayBetween(cmds, 500)
+}
\ No newline at end of file