CHF-435

Implementation of Health Check for Zigbee Dimmer (GE Plug-In/In-Wall Smart Dimmer)

devicetypes/smartthings/zigbee-dimmer-power.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zigbee-dimmer-power.src/README.md

@@ -0,0 +1,41 @@
+# GE Plug-In/In-Wall Smart Dimmer (ZigBee)
+
+
+
+Works with:
+
+* [GE In-Wall Smart Dimmer (ZigBee)](https://shop.smartthings.com/#!/products/ge-in-wall-smart-dimmer-switch)
+* [GE Plug-In Smart Dimmer (ZigBee)](https://www.smartthings.com/works-with-smartthings/ge/ge-plug-in-smart-dimmer-zigbee)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#Troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Refresh** - _refresh()_ command for status updates
+* **Power Meter** - ability to check the power meter(energy consumption) of device
+* **Sensor** - represents the device sensor capability
+* **Switch** - can detect state (possible values: on/off)
+* **Switch Level** - represents current light level, usually 0-100 in percent
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+A Zigbee dimmer with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime.
+This gives the device twice the amount of time to respond before it is marked as offline.
+Enrolls with default periodic reporting until newer 5 min interval is confirmed
+It then enrolls the device with updated checkInterval i.e. 12 mins
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [GE Z-Wave In-Wall Smart Dimmer (GE 45857) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/204988564-GE-In-Wall-Smart-Dimmer-45857GE-ZigBee-)
+* [GE Zigbee Plug-in Smart Dimmer (GE 45852) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/205239280-GE-Plug-In-Smart-Dimmer-45852GE-ZigBee-)

devicetypes/smartthings/zigbee-dimmer-power.src/zigbee-dimmer-power.groovy

@@ -21,6 +21,7 @@ metadata {
         capability "Sensor"
         capability "Switch"
         capability "Switch Level"
+        capability "Health Check"
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B04"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702"
@@ -70,8 +71,20 @@ def parse(String description) {
         }
     }
     else {
-        log.warn "DID NOT PARSE MESSAGE for description : $description"
+        def cluster = zigbee.parse(description)
-        log.debug zigbee.parseDescriptionAsMap(description)
+        if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
+            if (cluster.data[0] == 0x00){
+                log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
+                sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+            }
+            else {
+                log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+            }
+        }
+        else {
+            log.warn "DID NOT PARSE MESSAGE for description : $description"
+            log.debug zigbee.parseDescriptionAsMap(description)
+        }
     }
 }
 
@@ -87,11 +100,22 @@ def setLevel(value) {
     zigbee.setLevel(value)
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+    return zigbee.onOffRefresh()
+}
+
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
 }
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
+
+    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+    // enrolls with default periodic reporting until newer 5 min interval is confirmed
+    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
     refresh()
 }