Merge pull request #1337 from SmartThingsCommunity/master

Rolling up master to staging

devicetypes/smartthings/cree-bulb.src/cree-bulb.groovy

@@ -97,6 +97,7 @@ def refresh() {
 }
 
 def healthPoll() {
+    log.debug "healthPoll()"
     def cmds = zigbee.onOffRefresh() + zigbee.levelRefresh()
     cmds.each{ sendHubCommand(new physicalgraph.device.HubAction(it))}
 }

devicetypes/smartthings/ecobee-thermostat.src/ecobee-thermostat.groovy

@@ -655,6 +655,10 @@ void lowerSetpoint() {
 void alterSetpoint(temp) {
 
 	def mode = device.currentValue("thermostatMode")
+
+	if (mode == "off" || mode == "auto") {
+		log.warn "this mode: $mode does not allow alterSetpoint"
+	} else {
 		def heatingSetpoint = device.currentValue("heatingSetpoint")
 		def coolingSetpoint = device.currentValue("coolingSetpoint")
 		def deviceId = device.deviceNetworkId.split(/\./).last()
@@ -705,6 +709,7 @@ void alterSetpoint(temp) {
 		}
 		generateStatusEvent()
 	}
+}
 
 def generateStatusEvent() {
 

devicetypes/smartthings/nyce-open-closed-sensor.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/nyce-open-closed-sensor.src/README.md

@@ -0,0 +1,37 @@
+# Nyce Door/Window Sensor (Open/Close Sensor)
+
+
+
+Works with:
+
+* [NYCE Door/Window Sensor NCZ-3011](https://support.smartthings.com/hc/en-us/articles/204576764-NYCE-Door-Window-Sensor)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Contact Sensor** - can detect contact (with possible values - open/closed)
+* **Battery** - defines device uses a battery
+* **Refresh** - _refresh()_ command for status updates
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+A Category C2 Nyce Door/Window sensor that has 12min check-in interval
+
+## Battery Specification
+
+One 3V CR2032 battery required.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the sensor is out of range.
+Pairing needs to be tried again by placing the sensor closer to the hub.
+Instructions related to pairing, resetting and removing the sensor from SmartThings can be found in the following link:
+* [Nyce Door/Window Sensor](https://support.smartthings.com/hc/en-us/articles/204576764-NYCE-Door-Window-Sensor)

devicetypes/smartthings/nyce-open-closed-sensor.src/nyce-open-closed-sensor.groovy

@@ -23,6 +23,7 @@ metadata {
 		capability "Configuration"
 		capability "Contact Sensor"
 		capability "Refresh"
+		capability "Health Check"
 
 		command "enrollResponse"
 
@@ -273,23 +274,28 @@ private List parseIasMessage(String description) {
 	return resultListMap
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	return zigbee.readAttribute(0x001, 0x0020) // Read the Battery Level
+}
+
 def configure() {
+	// Device-Watch allows 2 check-in misses from device
+	sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+
 	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
 
-	def configCmds = [
+	def enrollCmds = [
-			//battery reporting and heartbeat
-			"zdo bind 0x${device.deviceNetworkId} 1 ${endpointId} 1 {${device.zigbeeId}} {}", "delay 200",
-			"zcl global send-me-a-report 1 0x20 0x20 600 3600 {01}", "delay 200",
-			"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 1500",
-
-
 			// Writes CIE attribute on end device to direct reports to the hub's EUID
 			"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
 			"send 0x${device.deviceNetworkId} 1 1", "delay 500",
 	]
 
 	log.debug "configure: Write IAS CIE"
-	return configCmds
+	// battery minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
+	return enrollCmds + zigbee.batteryConfig(30, 300) + refresh() // send refresh cmds as part of config
 }
 
 def enrollResponse() {
@@ -334,7 +340,8 @@ Integer convertHexToInt(hex) {
 
 def refresh() {
 	log.debug "Refreshing Battery"
-	[
+	def refreshCmds = [
 			"st rattr 0x${device.deviceNetworkId} ${endpointId} 1 0x20", "delay 200"
 	]
+	return refreshCmds + enrollResponse()
 }

devicetypes/smartthings/tyco-door-window-sensor.src/tyco-door-window-sensor.groovy

@@ -16,7 +16,7 @@
 import physicalgraph.zigbee.clusters.iaszone.ZoneStatus
 
 metadata {
-	definition (name: "Tyco Door/Window Sensor", namespace: "smartthings", author: "SmartThings", category: "C2") {
+	definition (name: "Tyco Door/Window Sensor", namespace: "smartthings", author: "SmartThings") {
 		capability "Battery"
 		capability "Configuration"
 		capability "Contact Sensor"