Adding changes mentioned by @strelitzia123

devicedata has been deprecated in favor of getstationsdata and will be removed at the end of November.

*Note* I haven't actually tested this change due to time limitations. Someone should check this out and verify it behaves properly before merging.

devicetypes/smartthings/dimmer-switch.src/.st-ignore

@@ -1,2 +0,0 @@
-.st-ignore
-README.md

devicetypes/smartthings/dimmer-switch.src/README.md

@@ -1,45 +0,0 @@
-# Z-wave Dimmer Switch
-
-
-
-Works with:
-
-* [GE Z-Wave In-Wall Smart Dimmer (GE 12724)](http://products.z-wavealliance.org/products/1197)
-* [GE Z-Wave In-Wall Smart Dimmer (Toggle) (GE 12729)](http://products.z-wavealliance.org/products/1201)
-* [GE Z-Wave Plug-in Smart Dimmer (GE 12718)](http://products.z-wavealliance.org/products/1191)
-
-## Table of contents
-
-* [Capabilities](#capabilities)
-* [Health](#device-health)
-* [Troubleshooting](#Troubleshooting)
-
-## Capabilities
-
-* **Switch Level** - it's defined to accept two parameters, the level and the rate of dimming
-* **Actuator** - represents that a Device has commands
-* **Indicator** - gives you the ability to set the indicator LED light on a Z-Wave switch
-* **Switch** - can detect state (possible values: on/off)
-* **Polling** - represents that poll() can be implemented for the device
-* **Refresh** - _refresh()_ command for status updates
-* **Sensor** - detects sensor events
-* **Health Check** - indicates ability to get device health notifications
-
-## Device Health
-
-Z-Wave Smart Dimmers (In-Wall, In-Wall(Toggle), Plug-In) are polled by the hub.
-As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
-Check-in interval = 32 mins.
-Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
-the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
-it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
-
-## Troubleshooting
-
-If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
-Pairing needs to be tried again by placing the device closer to the hub.
-Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
-* [General Z-Wave Dimmer/Switch Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200955890-Troubleshooting-GE-in-wall-switch-or-dimmer-won-t-respond-to-commands-or-automations-Z-Wave-)
-* [GE Z-Wave In-Wall Smart Dimmer (GE 12724) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200902600-GE-In-Wall-Paddle-Dimmer-Switch-GE-12724-Z-Wave-)
-* [GE Z-Wave In-Wall Smart Dimmer (Toggle) (GE 12729) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/207568463-GE-In-Wall-Smart-Toggle-Dimmer-GE-12729-Z-Wave-)
-* [GE Z-Wave Plug-in Smart Dimmer (GE 12718) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/202088474-GE-Plug-In-Smart-Dimmer-GE-12718-Z-Wave-)

devicetypes/smartthings/dimmer-switch.src/dimmer-switch.groovy

@@ -20,7 +20,6 @@ metadata {
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
-		capability "Health Check"
 
 		fingerprint mfr:"0063", prod:"4457", deviceJoinName: "Z-Wave Wall Dimmer"
 		fingerprint mfr:"0063", prod:"4944", deviceJoinName: "Z-Wave Wall Dimmer"
@@ -83,8 +82,6 @@ metadata {
 }
 
 def updated(){
-	// Device-Watch simply pings if no device events received for 32min(checkInterval)
-	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
   switch (ledIndicator) {
         case "on":
             indicatorWhenOn()
@@ -218,13 +215,6 @@ def poll() {
 	zwave.switchMultilevelV1.switchMultilevelGet().format()
 }
 
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-	refresh()
-}
-
 def refresh() {
 	log.debug "refresh() is called"
 	def commands = []

devicetypes/smartthings/smartpower-outlet.src/smartpower-outlet.groovy

@@ -143,7 +143,7 @@ def refresh() {
 def configure() {
 	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	// OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
 	refresh() + zigbee.onOffConfig(0, 300) + powerConfig()

devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy

@@ -104,7 +104,7 @@ def configure() {
     log.debug "Configuring Reporting and Bindings."
     // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig()

devicetypes/smartthings/zigbee-rgb-bulb.src/zigbee-rgb-bulb.groovy

@@ -28,8 +28,8 @@ metadata {
 		capability "Switch Level"
 		capability "Health Check"
 
-		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Gardenspot RGB", deviceJoinName: "OSRAM LIGHTIFY Gardenspot mini RGB"
+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Gardenspot RGB"
-		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY Gardenspot RGB", deviceJoinName: "OSRAM LIGHTIFY Gardenspot mini RGB"
+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY Gardenspot RGB"
 	}
 
 	// UI tile definitions

devicetypes/smartthings/zigbee-rgbw-bulb.src/zigbee-rgbw-bulb.groovy

@@ -145,7 +145,7 @@ def configure() {
     log.debug "Configuring Reporting and Bindings."
     // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     refresh()

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/zigbee-white-color-temperature-bulb.groovy

@@ -128,7 +128,7 @@ def configure() {
     log.debug "Configuring Reporting and Bindings."
     // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     refresh()

devicetypes/smartthings/zll-dimmer-bulb.src/zll-dimmer-bulb.groovy

@@ -11,9 +11,6 @@
  *  for the specific language governing permissions and limitations under the License.
  *
  */
-import groovy.transform.Field
-
-@Field Boolean hasConfiguredHealthCheck = false
 
 metadata {
     definition (name: "ZLL Dimmer Bulb", namespace: "smartthings", author: "SmartThings") {
@@ -24,7 +21,6 @@ metadata {
         capability "Refresh"
         capability "Switch"
         capability "Switch Level"
-        capability "Health Check"
 
         //fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0000,0019"
         fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0019"
@@ -100,38 +96,7 @@ def poll() {
     refresh()
 }
 
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-    return zigbee.levelRefresh()
-}
-
-def healthPoll() {
-    log.debug "healthPoll()"
-    def cmds = refresh()
-    cmds.each{ sendHubCommand(new physicalgraph.device.HubAction(it))}
-}
-
-def configureHealthCheck() {
-    Integer hcIntervalMinutes = 12
-    if (!hasConfiguredHealthCheck) {
-        log.debug "Configuring Health Check, Reporting"
-        unschedule("healthPoll")
-        runEvery5Minutes("healthPoll")
-        // Device-Watch allows 2 check-in misses from device
-        sendEvent(name: "checkInterval", value: hcIntervalMinutes * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-        hasConfiguredHealthCheck = true
-    }
-}
-
 def configure() {
-    log.debug "configure()"
+    log.debug "Configuring Reporting and Bindings."
     zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()
-    configureHealthCheck()
-}
-
-def updated() {
-    log.debug "updated()"
-    configureHealthCheck()
 }

devicetypes/smartthings/zll-white-color-temperature-bulb.src/zll-white-color-temperature-bulb.groovy

@@ -11,9 +11,6 @@
  *  for the specific language governing permissions and limitations under the License.
  *
  */
-import groovy.transform.Field
-
-@Field Boolean hasConfiguredHealthCheck = false
 
 metadata {
     definition (name: "ZLL White Color Temperature Bulb", namespace: "smartthings", author: "SmartThings") {
@@ -25,7 +22,6 @@ metadata {
         capability "Refresh"
         capability "Switch"
         capability "Switch Level"
-        capability "Health Check"
 
         attribute "colorName", "string"
         command "setGenericName"
@@ -100,41 +96,9 @@ def poll() {
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
 }
 
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-    return zigbee.levelRefresh()
-}
-
-def healthPoll() {
-    log.debug "healthPoll()"
-    def cmds = zigbee.onOffRefresh() + zigbee.levelRefresh()
-    cmds.each{ sendHubCommand(new physicalgraph.device.HubAction(it))}
-}
-
-def configureHealthCheck() {
-    Integer hcIntervalMinutes = 12
-    if (!hasConfiguredHealthCheck) {
-        log.debug "Configuring Health Check, Reporting"
-        unschedule("healthPoll")
-        runEvery5Minutes("healthPoll")
-        // Device-Watch allows 2 check-in misses from device
-        sendEvent(name: "checkInterval", value: hcIntervalMinutes * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-        hasConfiguredHealthCheck = true
-    }
-}
-
 def configure() {
-    log.debug "configure()"
+    log.debug "Configuring Reporting and Bindings."
-    configureHealthCheck()
     zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
-
-}
-
-def updated() {
-    log.debug "updated()"
-    configureHealthCheck()
 }
 
 def setColorTemperature(value) {

devicetypes/smartthings/zwave-switch-generic.src/.st-ignore

@@ -1,2 +0,0 @@
-.st-ignore
-README.md

devicetypes/smartthings/zwave-switch-generic.src/README.md

@@ -1,39 +0,0 @@
-# Z-wave Switch
-
-
-
-Works with: 
-
-* [Leviton Appliance Module (DZPA1-1LW)](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
-* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave)](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)
-
-## Table of contents
-
-* [Capabilities](#capabilities)
-* [Health](#device-health)
-
-## Capabilities
-
-* **Actuator** - represents that a Device has commands
-* **Health Check** - indicates ability to get device health notifications
-* **Switch** - can detect state (possible values: on/off)
-* **Polling** - represents that poll() can be implemented for the device
-* **Refresh** - _refresh()_ command for status updates
-* **Sensor** - detects sensor events
-
-## Device Health
-
-A Category C5 Leviton Appliance Module (DZPA1-1LW) and GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) polled by the hub.
-As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
-Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
-Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
-the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
-it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
-
-## Troubleshooting
-
-If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
-Pairing needs to be tried again by placing the device closer to the hub.
-Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
-* [Leviton Appliance Module (DZPA1-1LW) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
-* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)

devicetypes/smartthings/zwave-switch-generic.src/zwave-switch-generic.groovy

@@ -14,15 +14,12 @@
 metadata {
 	definition (name: "Z-Wave Switch Generic", namespace: "smartthings", author: "SmartThings") {
 		capability "Actuator"
-		capability "Health Check"
  		capability "Switch"
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
 
 		fingerprint inClusters: "0x25", deviceJoinName: "Z-Wave Switch"
-		fingerprint mfr:"001D", prod:"1A02", deviceJoinName: "Z-Wave Switch"
-		fingerprint mfr:"0063", prod:"4F50", deviceJoinName: "Z-Wave Switch"
 	}
 
 	// simulator metadata
@@ -53,11 +50,6 @@ metadata {
 	}
 }
 
-def updated(){
-// Device-Watch simply pings if no device events received for checkInterval duration of 32min = 2 * 15min + 2min lag time
-	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
-}
-
 def parse(String description) {
 	def result = null
 	def cmd = zwave.parse(description, [0x20: 1, 0x70: 1])
@@ -134,13 +126,6 @@ def poll() {
 	])
 }
 
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-	refresh()
-}
-
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),

devicetypes/smartthings/zwave-switch.src/.st-ignore

@@ -1,2 +0,0 @@
-.st-ignore
-README.md

devicetypes/smartthings/zwave-switch.src/README.md

@@ -1,49 +0,0 @@
-# Z-Wave Switch
-
-
-Works with: 
-
-* [GE Z-Wave Plug-In Smart Switch (12719)](http://products.z-wavealliance.org/products/1193)
-* [GE Z-Wave In-Wall Smart Outlet (12721)](http://products.z-wavealliance.org/products/1195)
-* [GE Z-Wave In-Wall Smart Switch (12722)](http://products.z-wavealliance.org/products/1196)
-* [GE Z-Wave In-Wall Smart Toggle Switch (12727)](http://products.z-wavealliance.org/products/1200)
-
-
-## Table of contents
-
-* [Capabilities](#capabilities)
-* [Health](#device-health)
-* [Troubleshooting](#Troubleshooting)
-
-## Capabilities
-
-* **Actuator** - represents that a Device has commands
-* **Indicator** - gives you the ability to set the indicator LED light on a Z-Wave switch
-* **Switch** - can detect state (possible values: on/off)
-* **Polling** - represents that poll() can be implemented for the device
-* **Refresh** - _refresh()_ command for status updates
-* **Sensor** - detects sensor events
-* **Health Check** - indicates ability to get device health notifications
-
-## Device Health
-
-Z-Wave Switches (Plug-In, In-Wall(Toggle Switch, Switch, Outlet)) are polled by the hub.
-As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
-Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
-Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
-the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
-it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
-
-
-## Troubleshooting
-
-If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
-Pairing needs to be tried again by placing the device closer to the hub.
-Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
-* [General Z-Wave Dimmer/Switch Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200955890-Troubleshooting-GE-in-wall-switch-or-dimmer-won-t-respond-to-commands-or-automations-Z-Wave-)
-* [GE Z-Wave Plug-In Smart Switch (12719) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200903070-GE-Plug-In-Smart-Switch-GE-12719-Z-Wave)
-* [GE Z-Wave In-Wall Smart Outlet (12721) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200903020-GE-In-Wall-Smart-Outlet-GE-12721-Z-Wave)
-* [GE Z-Wave In-Wall Smart Switch (12722) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200902540-GE-In-Wall-Smart-Switch-GE-12722-Z-Wave)
-* [GE Z-Wave In-Wall Smart Toggle Switch (12727) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/207568933-GE-In-Wall-Smart-Toggle-Switch-GE-12727-Z-Wave)
-
-

devicetypes/smartthings/zwave-switch.src/zwave-switch.groovy

@@ -19,7 +19,6 @@ metadata {
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
-		capability "Health Check"
 
 		fingerprint mfr:"0063", prod:"4952", deviceJoinName: "Z-Wave Wall Switch"
 		fingerprint mfr:"0063", prod:"5257", deviceJoinName: "Z-Wave Wall Switch"
@@ -65,8 +64,6 @@ metadata {
 }
 
 def updated(){
-		// Device-Watch simply pings if no device events received for 32min(checkInterval)
-		sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
   switch (ledIndicator) {
         case "on":
             indicatorWhenOn()
@@ -159,13 +156,6 @@ def poll() {
 	])
 }
 
-/**
-  * PING is used by Device-Watch in attempt to reach the Device
-**/
-def ping() {
-		refresh()
-}
-
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),

smartapps/dianoga/netatmo-connect.src/netatmo-connect.groovy

@@ -387,18 +387,18 @@ def getDeviceList() {
 	state.deviceDetail = [:]
 	state.deviceState = [:]
 
-	apiGet("/api/devicelist") { response ->
+	apiGet("/api/getstationsdata") { response ->
 		response.data.body.devices.each { value ->
 			def key = value._id
 			deviceList[key] = "${value.station_name}: ${value.module_name}"
 			state.deviceDetail[key] = value
             state.deviceState[key] = value.dashboard_data
-		}
+			value.modules.each { value2 ->            
-		response.data.body.modules.each { value ->
+                def key2 = value2._id
-			def key = value._id
+                deviceList[key2] = "${value.station_name}: ${value2.module_name}"
-			deviceList[key] = "${state.deviceDetail[value.main_device].station_name}: ${value.module_name}"
+                state.deviceDetail[key2] = value2
-			state.deviceDetail[key] = value
+                state.deviceState[key2] = value2.dashboard_data            
-            state.deviceState[key] = value.dashboard_data
+            }
 		}
 	}
 

smartapps/smartthings/hue-connect.src/hue-connect.groovy

@@ -37,10 +37,7 @@ preferences {
 
 def mainPage() {
 	def bridges = bridgesDiscovered()
-
+	if (state.username && bridges) {
-	if (state.refreshUsernameNeeded) {
-		return bridgeLinking()
-	} else if (state.username && bridges) {
 		return bulbDiscovery()
 	} else {
 		return bridgeDiscovery()
@@ -105,22 +102,13 @@ def bridgeLinking() {
 
 	def nextPage = ""
 	def title = "Linking with your Hue"
-	def paragraphText
+    def paragraphText
 	if (selectedHue) {
-		if (state.refreshUsernameNeeded) {
-			paragraphText = "The current Hue username is invalid.\n\nPlease press the button on your Hue Bridge to re-link. "
-		} else {
 		paragraphText = "Press the button on your Hue Bridge to setup a link. "
-		}
+    } else {
-	} else {
+    	paragraphText = "You haven't selected a Hue Bridge, please Press \"Done\" and select one before clicking next."
-		paragraphText = "You haven't selected a Hue Bridge, please Press \"Done\" and select one before clicking next."
+    }
-	}
 	if (state.username) { //if discovery worked
-		if (state.refreshUsernameNeeded) {
-			state.refreshUsernameNeeded = false
-			// Issue one poll with new username to cancel local polling with old username
-			poll()
-		}
 		nextPage = "bulbDiscovery"
 		title = "Success!"
 		paragraphText = "Linking to your hub was a success! Please click 'Next'!"
@@ -927,15 +915,8 @@ private handleCommandResponse(body) {
 					updates[childDeviceNetworkId]."$eventType" = v
 				}
 			}
-		} else if (payload?.error) {
+		} else if (payload.error) {
-			log.warn "Error returned from Hue bridge, error = ${payload?.error}"
+			log.warn "Error returned from Hue bridge error = ${body?.error}"
-			// Check for unauthorized user
-			if (payload?.error?.type?.value == 1) {
-				log.error "Hue username is not valid"
-				state.refreshUsernameNeeded = true
-				state.username = null
-			}
-			return []
 		}
 	}