MSA-1660: The Qubino Weatherstation device is a RF 433MHz to Z-Wave bridge device, that translates the data reported by RF sensors into a Z-Wave Multichannel device.

It provides two channel temperature and humidity measurements (reported by separate sensors) along with the rain rate, wind gust, wind velocity, wind direction and temperature measurement.

The device handler is compatible with most available automation SmartApps that do not allow for non-capability attributes to be used (the channel 1 temperature and humidity are mirrored for these), whereas with SmartApps that allow custom attributes to be used as condition triggers it is fully compatible.

The device handler takes care of setting up a multichannel lifeline association in order to receive pushed multichannel encapsulated reports from the device's endpoints, allowing for less network congestion as would be present in a polling approach.

devicetypes/goap/qubino-weatherstation.src/qubino-weatherstation.groovy

@@ -0,0 +1,486 @@
+/**
+ *  Qubino Weatherstation
+ *	Device Handler 
+ *	Version 1.0
+ *  Date: 16.12.2016
+ *	Author: Kristjan Jamšek (Kjamsek), Goap d.o.o.
+ *  Copyright 2016 Kristjan Jamšek
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ * - DEVICE HANDLER FOR QUBINO WEATHERSTATION Z-WAVE DEVICE -  
+ *	The handler supports all unsecure functions of the Qubino Weatherstation device. Configuration parameters and
+ *	association groups can be set in the device's preferences screen, but they are applied on the device only after
+ *	pressing the 'Set configuration' and 'Set associations' buttons on the bottom of the details view. 
+ *
+ *	This device handler supports data values that are currently not implemented as capabilities, so custom attribute 
+ *	states are used. Please use a SmartApp that supports custom attribute monitoring with this device in your rules.
+ *	By default the 'Temperature Measurement' and 'Relative Humidity Measurement' capability states are mirrored from
+ *	the custom attribute state values 'temperatureCh1' and 'humidityCh1'.
+ *
+ *	This device handler uses hubAction in configure() method in order to set a MultiChannel Lifeline association to the
+ *	device, so reports from all endpoints can be received. 
+ *
+ *
+ *	CHANGELOG:
+ *	0.99: Final release code cleanup and commenting
+ *	1.00: Added comments to code for readability
+ */
+metadata {
+	definition (name: "Qubino Weatherstation", namespace: "Goap", author: "Kristjan Jamšek") {
+		capability "Configuration" //Needed for configure() function to set MultiChannel Lifeline Association Set
+		capability "Temperature Measurement" //Used on main tile, needed in order to have the device appear in capabilities lists, mirrors temperatureCh1 attribute states
+		capability "Relative Humidity Measurement" //Needed in order to have the device appear in capabilities lists, mirrors humidityCh1 attribute states
+		capability "Sensor" // - Tagging capability
+		
+		attribute "temperatureCh1", "number" // temperature attribute for Ch1 Temperature reported by device's endpoint 1
+		attribute "windDirection", "number" // wind direction attribute for Wind Gauge - Direction reported by device's endpoint 2
+		attribute "windVelocity", "number" // wind velocity attribute for Wind Gauge - Velocity reported by device's endpoint 3
+		attribute "windGust", "number" // wind gust velocity attribute for Wind Gauge - Wind gust reported by device's endpoint 4
+		attribute "windTemperature", "number" // wind temperature attribute for Wind Gauge - Temperature reported by device's endpoint 5
+		attribute "windChillTemperature", "number" // wind chill temperature attribute for Wind Gauge - Wind Chill reported by device's endpoint 6
+		attribute "rainRate", "number" // rain rate attribute for Rain Sensor data reported by device's endpoint 7
+		attribute "humidityCh1", "number" // humidity attribute for Ch1 Humidity reported by device's endpoint 8
+		attribute "temperatureCh2", "number" // temperature attribute for Ch2 Temperature reported by device's endpoint 9
+		attribute "humidityCh2", "number" // humidity attribute for Ch2 Humidity reported by device's endpoint 10
+		
+		attribute "setConfigParams", "string" // attribute for tile element for setConfigurationParams command
+		attribute "setAssocGroups", "string" // attribute for tile element for setAssociations command
+		
+		command "setConfigurationParams" // command to issue Configuration Set command sequence according to user's preferences
+		command "setAssociations" // command to issue Association Set command sequence according to user's preferences
+
+        fingerprint mfr:"0159", prod:"0007", model:"0053"  //Manufacturer Information values for Qubino Weatherstation
+	}
+
+
+	simulator {
+		// TESTED WITH PHYSICAL DEVICE - UNNEEDED
+	}
+
+	tiles(scale: 2) {
+		valueTile("temperature", "device.temperature") {
+			state("temperature", label:'${currentValue} °', unit:"°", icon: "st.Weather.weather2", backgroundColors: [
+				// Celsius Color Range
+				[value: 0, color: "#153591"],
+				[value: 7, color: "#1e9cbb"],
+				[value: 15, color: "#90d2a7"],
+				[value: 23, color: "#44b621"],
+				[value: 29, color: "#f1d801"],
+				[value: 33, color: "#d04e00"],
+				[value: 36, color: "#bc2323"],
+				// Fahrenheit Color Range
+				[value: 40, color: "#153591"],
+				[value: 44, color: "#1e9cbb"],
+				[value: 59, color: "#90d2a7"],
+				[value: 74, color: "#44b621"],
+				[value: 84, color: "#f1d801"],
+				[value: 92, color: "#d04e00"],
+				[value: 96, color: "#bc2323"]
+			])
+		}		
+		valueTile("humidity", "device.humidity") {
+			state("humidity", label:'${currentValue} %', unit:"%", display:false)
+		}		
+		standardTile("temperatureCh1", "device.temperatureCh1", width: 3, height: 3) {
+			state("temperatureCh1", label:'Temperature Ch1: ${currentValue} °', unit:'°', icon: 'st.Weather.weather2')
+		}
+		standardTile("windDirection", "device.windDirection", width: 3, height: 3) {
+			state("windDirection", label:'Wind Direction: ${currentValue} °', unit: "°", icon: 'st.Outdoor.outdoor20')
+		}
+		standardTile("windVelocity", "device.windVelocity", width: 3, height: 3) {
+			state("windVelocity", label:'Wind Velocity: ${currentValue} m/s', unit:"m/s", icon: 'st.Weather.weather1')
+		}
+		standardTile("windGust", "device.windGust", width: 3, height: 3) {
+			state("windGust", label:'Wind Gust: ${currentValue} m/s', unit:"m/s", icon: 'st.Weather.weather1')
+		}
+		standardTile("windTemperature", "device.windTemperature", width: 3, height: 3) {
+			state("windTemperature", label:'Wind Temperature: ${currentValue} °', unit:'°', icon: 'st.Weather.weather2')
+		}
+		standardTile("windChillTemperature", "device.windChillTemperature", width: 3, height: 3) {
+			state("windChillTemperature", label:'Wind Chill: ${currentValue} °', unit:'°', icon: 'st.Weather.weather2')
+		}
+		standardTile("rainRate", "device.rainRate", width: 3, height: 3) {
+			state("rainRate", label:'Rain Sensor: ${currentValue} mm/h', unit:"mm/h", icon: 'st.Weather.weather10')
+		}
+		standardTile("humidityCh1", "device.humidityCh1", width: 3, height: 3) {
+			state("humidityCh1", label:'Humidity Ch1: ${currentValue} %', unit:"%", icon: 'st.Weather.weather12')
+		}
+		standardTile("temperatureCh2", "device.temperatureCh2", width: 3, height: 3) {
+			state("temperatureCh2", label:'Temperature Ch2: ${currentValue} °', unit:'°', icon: 'st.Weather.weather2')
+		}
+		standardTile("humidityCh2", "device.humidityCh2", width: 3, height: 3) {
+			state("humidityCh2", label:'Humidity Ch2: ${currentValue} %', unit:"%", icon: 'st.Weather.weather12')
+		}
+		standardTile("setConfigParams", "device.setConfigParams", decoration: "flat", width: 3, height: 3) {
+			state("setConfigParams", label:'Set configuration', action:'setConfigurationParams', icon: "st.secondary.tools")
+		}
+		standardTile("setAssocGroups", "device.setAssocGroups", decoration: "flat", width: 3, height: 3) {
+			state("setAssocGroups", label:'Set associations', action:'setAssociations', icon: "st.secondary.tools")
+		}
+		
+		main("temperature")
+		details(["temperatureCh1", "humidityCh1", "windDirection", "windVelocity", "windGust", "windTemperature", "windChillTemperature", "rainRate", "temperatureCh2", "humidityCh2", "setConfigParams", "setAssocGroups"])
+
+	}
+	preferences {
+/**
+*			--------	CONFIGURATION PARAMETER SECTION	--------
+*/
+				input name: "param1", type: "number", range: "0..8800", required: false,
+					title: "1. Wind Gauge, Wind Gust Top Value. " +
+						   "If the Wind Gust is higher than the parameter value, the device triggers an association.\n" +
+						   "Available settings:\n" +
+						   "0 ... 8800 = value from 0,00 m/s to 88,00 m/s,\n" +
+						   "Default value: 1000 (10,00 m/s)."
+				input name: "param2", type: "number", range: "0..30000", required: false,
+					title: "2. Rain Gauge, Rain Rate Top Value. " +
+						   "If the Rain Sensor Rain Rate is higher than the parameter value, the device triggers an association.\n" +
+						   "Available settings:\n" +
+						   "0 ... 30000 = value from 0,00 mm/h to 300,00 mm/h,\n" +
+						   "Default value: 200 (2,00 mm/h)."          
+				input name: "param3", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "3. Wind Gauge, Wind Gust. " +
+						   "Available settings:\n" +
+						   "0 = If the Wind Gust is higher than the parameter number 1 value, then the device sends a Basic Set 0x00,\n" +
+						   "1 = If the Wind Gust is higher than the parameter number 1 value, then the device sends a Basic Set 0xFF,\n" +
+						   "Default value: 1."
+				input name: "param4", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "4. Rain Gauge, Rain Rate. " +
+						   "Available settings:\n" +
+						   "0 = If the Rain Rate is higher than the parameter number 2 value, then the device sends a Basic Set 0x00,\n" +
+						   "1 = If the Rain Rate is higher than the parameter number 2 value, then the device sends a Basic Set 0xFF,\n" +
+						   "Default value: 1."	
+				input name: "param5", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "5. Endpoint 1 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param6", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "6. Endpoint 2 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param7", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "7. Endpoint 3 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param8", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "8. Endpoint 4 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param9", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "9. Endpoint 5 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param10", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "10. Endpoint 6 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param11", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "11. Endpoint 7 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param12", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "12. Endpoint 8 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param13", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "13. Endpoint 9 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param14", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "14. Endpoint 10 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param15", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "15. Random ID enable/disable " +
+						   "Available settings:\n" +
+						   "0 = Random ID disabled,\n" +
+						   "1 = Random ID enabled,\n" +
+						   "Default value: 0."
+/**
+*			--------	ASSOCIATION GROUP SECTION	--------
+*/
+				input name: "assocGroup2", type: "text", required: false,
+					title: "Association group 2: \n" +
+						   "Basic On/Off command will be sent to associated nodes when the Wind Gust of the Wind Gauge exceeds the Configuration parameter 1 value. \n" +
+						   "NOTE: Insert the node Id value of the devices you wish to associate this group with. Multiple nodeIds can also be set at once by separating individual values by a comma (2,3,...)."
+						   
+				input name: "assocGroup3", type: "text", required: false,
+					title: "Association group 3: \n" +
+						   "Basic On/Off command will be sent to associated nodes when the Rain Rate exceeds the Configuration parameter 2 value. \n" +
+						   "NOTE: Insert the node Id value of the devices you wish to associate this group with. Multiple nodeIds can also be set at once by separating individual values by a comma (2,3,...)."
+	}
+}
+/**
+*	--------	HELPER METHODS SECTION	--------
+*/
+/**
+ * Converts a list of String type node id values to Integer type.
+ *
+ * @param stringList - a list of String type node id values.
+ * @return stringList - a list of Integer type node id values.
+*/
+def convertStringListToIntegerList(stringList){
+	for(int i=0;i<stringList.size();i++){
+		stringList[i] = stringList[i].toInteger()
+	}
+	return stringList
+}
+/**
+ * Converts temperature values to fahrenheit or celsius scales accordign to user's setting.
+ *
+ * @param scaleParam user set scale parameter.
+ * @param encapCmd received temperature parsed value.
+ * @return String type value of the converted temperature value.
+*/
+def convertDegrees(scaleParam, encapCmd){
+	switch (scaleParam) {
+		default:
+				break;
+		case "F":
+				if(encapCmd.scale == 1){
+					return encapCmd.scaledSensorValue.toString()
+				}else{
+					return (encapCmd.scaledSensorValue * 9 / 5 + 32).toString()
+				}
+				break;
+		case "C":
+				if(encapCmd.scale == 0){
+					return encapCmd.scaledSensorValue.toString()
+				}else{
+					return (encapCmd.scaledSensorValue * 9 / 5 + 32).toString()
+				}
+				break;
+	}
+}
+/*
+*	--------	HANDLE COMMANDS SECTION	--------
+*/
+/**
+ * Configuration capability command handler that executes after module inclusion to remove existing singlechannel association Lifeline and replace it
+ * with a multichannel Lifeline association setting for node id 1 and endpoint 1, which enables modules to report multichannel encapsulated frames.
+ *
+ * @param void
+ * @return List of commands that will be executed in sequence with 500 ms delay inbetween.
+*/
+def configure() {
+	log.debug "Qubino Weatherstation: configure()"
+	/** In this method we first clear the association group 1 that is set by SmartThings automatically.
+	* Afterwards we use physicalgraph.device.HubAction("8E0101000101") as a workaround for SmartThings' MultiChannel Association Command Class implementation,
+	* where we cannot set a node id and endpoint id. The hardcoded parameter "8E0101000101" should be interpreted in sequence as hexadecimal byte values:
+	* 8E010100 - Command class and command values, along with the field for singlechannel node id omitted
+	* 0101 - These two byte values represent the multichannel node id 01 followed by the endpoint id 01 (in general this value can be left as is unless 
+	*		 multiple subordinated controllers are included in your network. In that case please adjust these two value to the correct id.
+	*/
+	def assocCmds = []
+	assocCmds << zwave.associationV1.associationRemove(groupingIdentifier:1, nodeId:zwaveHubNodeId).format()
+	assocCmds << new physicalgraph.device.HubAction("8E0101000101")
+	return delayBetween(assocCmds, 500)
+}
+/**
+ * setAssociations command handler that sets user selected association groups. In case no node id is insetred the group is instead cleared.
+ * Lifeline association hidden from user influence by design.
+ *
+ * @param void
+ * @return List of Association commands that will be executed in sequence with 500 ms delay inbetween.
+*/
+def setAssociations() {
+	log.debug "Qubino Weatherstation: setAssociations()"
+	def assocSet = []
+	if(settings.assocGroup2 != null){
+		def group2parsed = settings.assocGroup2.tokenize(",")
+		group2parsed = convertStringListToIntegerList(group2parsed)
+		assocSet << zwave.associationV1.associationSet(groupingIdentifier:2, nodeId:group2parsed).format()
+	}else{
+		assocSet << zwave.associationV1.associationRemove(groupingIdentifier:2, nodeId: 0).format()
+	}
+	if(settings.assocGroup3 != null){
+		def group3parsed = settings.assocGroup3.tokenize(",")
+		group3parsed = convertStringListToIntegerList(group3parsed)
+		assocSet << zwave.associationV1.associationSet(groupingIdentifier:3, nodeId:group3parsed).format()
+	}else{
+		assocSet << zwave.associationV1.associationRemove(groupingIdentifier:3, nodeId: 0).format()
+	}
+	return delayBetween(assocSet, 500)
+	
+}
+/**
+ * setConfigurationParams command handler that sets user selected configuration parameters on the device. 
+ * In case no value is set for a specific parameter the method skips setting that parameter.
+ * Secure mdoe setting hidden from user influence by design.
+ *
+ * @param void
+ * @return List of Configuration Set commands that will be executed in sequence with 500 ms delay inbetween.
+*/
+def setConfigurationParams() {
+	log.debug "Qubino Weatherstation: setConfigurationParams()"
+	def configSequence = []
+	if(settings.param1 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 1, size: 2, scaledConfigurationValue: settings.param1.toInteger()).format()
+	}
+	if(settings.param2 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 2, size: 2, scaledConfigurationValue: settings.param2.toInteger()).format()
+	}
+	if(settings.param3 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 3, size: 1, scaledConfigurationValue: settings.param3.toInteger()).format()
+	}
+	if(settings.param4 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 4, size: 1, scaledConfigurationValue: settings.param4.toInteger()).format()
+	}
+	if(settings.param5 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 5, size: 1, scaledConfigurationValue: settings.param5.toInteger()).format()
+	}
+	if(settings.param6 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 6, size: 1, scaledConfigurationValue: settings.param6.toInteger()).format()
+	}
+	if(settings.param7 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 7, size: 1, scaledConfigurationValue: settings.param7.toInteger()).format()
+	}
+	if(settings.param8 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 8, size: 1, scaledConfigurationValue: settings.param8.toInteger()).format()
+	}
+	if(settings.param9 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 9, size: 1, scaledConfigurationValue: settings.param9.toInteger()).format()
+	}
+	if(settings.param10 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 10, size: 1, scaledConfigurationValue: settings.param10.toInteger()).format()
+	}
+	if(settings.param11 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 11, size: 1, scaledConfigurationValue: settings.param11.toInteger()).format()
+	}
+	if(settings.param12 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 12, size: 1, scaledConfigurationValue: settings.param12.toInteger()).format()
+	}
+	if(settings.param13 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 13, size: 1, scaledConfigurationValue: settings.param13.toInteger()).format()
+	}
+	if(settings.param14 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 14, size: 1, scaledConfigurationValue: settings.param14.toInteger()).format()
+	}
+	if(settings.param15 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 15, size: 1, scaledConfigurationValue: settings.param15.toInteger()).format()
+	}	
+	return delayBetween(configSequence, 500)
+}
+/*
+*	--------	EVENT PARSER SECTION	--------
+*/
+/**
+ * parse function takes care of parsing received bytes and passing them on to event methods.
+ *
+ * @param description String type value of the received bytes.
+ * @return Parsed result of the received bytes.
+*/
+def parse(String description) {
+	log.debug "Qubino Weatherstation: Parsing '${description}'"
+	def result = null
+    def cmd = zwave.parse(description)
+    if (cmd) {
+		result = zwaveEvent(cmd)
+        log.debug "Parsed ${cmd} to ${result.inspect()}"
+    } else {
+		log.debug "Non-parsed event: ${description}"
+    }
+    return result
+}
+/**
+ * Event method for MultiChannelCmdEncap encapsulation frames.
+ *
+ * @param cmd Type physicalgraph.zwave.commands.multichannelv3.MultiChannelCmdEncap received command.
+ * @return List of events that will update UI elements for data display.
+*/
+def zwaveEvent(physicalgraph.zwave.commands.multichannelv3.MultiChannelCmdEncap cmd) {
+	def encapsulatedCommand = cmd.encapsulatedCommand([0x30: 1, 0x31: 1])
+	def tempScale = location.temperatureScale
+	def resultEvents = []
+	switch (cmd.sourceEndPoint) {
+		default:
+				break;
+		case 1:
+				resultEvents << createEvent(name:"temperatureCh1", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Temperature Ch1: "+convertDegrees(tempScale,encapsulatedCommand)+"°"+location.temperatureScale)
+				resultEvents << createEvent(name:"temperature", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Temperature Ch1: "+convertDegrees(tempScale,encapsulatedCommand)+"°"+location.temperatureScale, displayed: false)
+				break;
+		case 2:
+				resultEvents << createEvent(name:"windDirection", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"°", descriptionText: "Wind Direction: "+encapsulatedCommand.scaledSensorValue.toString()+" °")
+				break;
+		case 3:
+				resultEvents << createEvent(name:"windVelocity", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"m/s", descriptionText: "Wind Velocity: "+encapsulatedCommand.scaledSensorValue.toString()+" m/s")
+				break;
+		case 4:
+				resultEvents << createEvent(name:"windGust", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"m/s", descriptionText: "Wind Gust: "+encapsulatedCommand.scaledSensorValue.toString()+" m/s")
+				break;
+		case 5:
+				resultEvents << createEvent(name:"windTemperature", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Wind Temperature: "+convertDegrees(tempScale,encapsulatedCommand)+" °"+location.temperatureScale)
+				break;
+		case 6:
+				resultEvents << createEvent(name:"windChillTemperature", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Wind Chill: "+convertDegrees(tempScale,encapsulatedCommand)+" °"+location.temperatureScale)
+				break;
+		case 7:
+				resultEvents << createEvent(name:"rainRate", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"mm/h", descriptionText: "Rain Sensor: "+encapsulatedCommand.scaledSensorValue.toString()+" mm/h")
+				break;
+		case 8:
+				resultEvents << createEvent(name:"humidity", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"%", descriptionText: "Humidity Ch1: "+encapsulatedCommand.scaledSensorValue.toString()+" %", displayed: false)
+				resultEvents << createEvent(name:"humidityCh1", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"%", descriptionText: "Humidity Ch1: "+encapsulatedCommand.scaledSensorValue.toString()+" %")
+				break;
+		case 9:
+				resultEvents << createEvent(name:"temperatureCh2", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Temperature Ch2: "+convertDegrees(tempScale,encapsulatedCommand)+" °"+location.temperatureScale)
+				break;
+		case 10:
+				resultEvents << createEvent(name:"humidityCh2", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"%", descriptionText: "Humidity Ch2: "+encapsulatedCommand.scaledSensorValue.toString()+" %")
+				break;
+	}
+	return resultEvents
+}

devicetypes/smartthings/life360-user.src/life360-user.groovy

@@ -39,7 +39,7 @@ metadata {
 }
 
 def generatePresenceEvent(boolean present) {
-	log.debug "Here in generatePresenceEvent!"
+	log.info "Life360 generatePresenceEvent($present)"
 	def value = formatValue(present)
 	def linkText = getLinkText(device)
 	def descriptionText = formatDescriptionText(linkText, present)

devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy

@@ -128,7 +128,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07) {
 					if (cluster.data[0] == 0x00){
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"

devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy

@@ -132,7 +132,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07) {
 					if (cluster.data[0] == 0x00) {
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"

devicetypes/smartthings/smartsense-multi-sensor.src/smartsense-multi-sensor.groovy

@@ -161,7 +161,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07) {
 					if(cluster.data[0] == 0x00) {
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
@@ -339,7 +339,7 @@ private Map getContactResult(value) {
 	log.debug "Contact: ${device.displayName} value = ${value}"
 	def descriptionText = value == 'open' ? '{{ device.displayName }} was opened' : '{{ device.displayName }} was closed'
 	sendEvent(name: 'contact', value: value, descriptionText: descriptionText, displayed: false, translatable: true)
-	sendEvent(name: 'status', value: value, descriptionText: descriptionText, translatable: true)
+	return [name: 'status', value: value, descriptionText: descriptionText, translatable: true]
 }
 
 private getAccelerationResult(numValue) {

devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy

@@ -119,7 +119,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07){
 					if (cluster.data[0] == 0x00) {
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy

@@ -103,7 +103,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07) {
 					if (cluster.data[0] == 0x00){
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"

smartapps/cubicrobotics/cubic-butler-for-smart-home.src/cubic-butler-for-smart-home.groovy

@@ -1,327 +0,0 @@
-/**
- *  Cubic Home
- * sdfssdfsfsdfsdfdsf
- *  Copyright 2016 Nikolay Zenovkin
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-definition(
-        name: "Cubic Butler for Smart Home",
-        namespace: "cubicrobotics",
-        author: "Cubic Robotics",
-        description: "Hey, I’m Cubic, AI butler for smart home! \n" +
-                "I am the one and only app you need to control an entire home. \n" +
-                "Right now I can help you to control your SmartThings devices via natural speech and dashboard.\n" +
-                "Speak naturally, don’t learn robot! My A.I. is designed for a smart home control.\n" +
-                "- You don’t have to remember exact commands and phrases.\n" +
-                "- I have memory, and every new request will be processed in the context of previous ones.\n" +
-                "- I can ask clarifying questions, if I’m not sure what you mean.",
-        category: "Convenience",
-        iconUrl: "https://lh3.googleusercontent.com/GX5BRhaFq22HpAEU6tD4JXvizlxWFuB9zjyZE39-pLpZvQvvUmVpWXa0v4-oaxz4tg=w300-rw",
-        iconX2Url: "https://lh3.googleusercontent.com/GX5BRhaFq22HpAEU6tD4JXvizlxWFuB9zjyZE39-pLpZvQvvUmVpWXa0v4-oaxz4tg=w300-rw",
-        iconX3Url: "https://lh3.googleusercontent.com/GX5BRhaFq22HpAEU6tD4JXvizlxWFuB9zjyZE39-pLpZvQvvUmVpWXa0v4-oaxz4tg=w300-rw",
-        oauth: [displayName: "Cubic Home", displayLink: "http://cubic.ai/"])
-
-
-preferences {
-    section("Welcome to Cubic") {
-        // TODO: put inputs here
-    }
-    section("Allow Cubic to control these switches") {
-        input "switches", "capability.switch", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these motion sensors") {
-        input "motionSensors", "capability.motionSensor", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these bulbs") {
-        input "lamps", "capability.colorControl", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these thermostats") {
-        input "thermostats", "capability.thermostat", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these water sensors") {
-        input "waterSensors", "capability.waterSensor", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these CO sensors") {
-        input "smokeSensors", "capability.carbonMonoxideDetector", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these door controls") {
-        input "doorControls", "capability.doorControl", multiple: true, required: false
-    }
-
-}
-
-
-mappings {
-    path("/devices") {
-        action:
-        [
-                GET: "getDevices"
-        ]
-    }
-    path("/devices/:id") {
-        action:
-        [
-                PUT: "updateDevice",
-                GET: "getDevice"
-        ]
-    }
-}
-
-def installed() {
-    log.debug "Installed with settings: ${settings}"
-
-    initialize()
-}
-
-def updated() {
-    log.debug "Updated with settings: ${settings}"
-
-    unsubscribe()
-    initialize()
-}
-
-def initialize() {
-    subscribe(motionSensors, "motion", motionHandler)
-    subscribe(switches, "switch", switchHandler)
-    subscribe(thermostats, "thermostat.temperature", thermostatHandler)
-    subscribe(waterSensors, "waterSensor", waterHandler)
-    subscribe(smokeSensors, "carbonMonoxideDetector", smokeHandler)
-    subscribe(doorControls, "doorControl", doorControlHandler)
-}
-
-def doorControlHandler(evt) {
-    if (evt.isStateChanged()) {
-        sendPushEvent(evt.deviceId,
-                "DOOR_CONTROL_SMART_THINGS",
-                evt.value
-        )
-    }
-}
-
-def smokeHandler(evt) {
-    if (evt.isStateChanged()) {
-        sendPushEvent(evt.deviceId,
-                "SMOKE_CO_SENSOR_SMART_THINGS",
-                evt.value
-        )
-    }
-}
-
-def thermostatHandler(evt) {
-    if (evt.isStateChanged()) {
-        sendPushEvent(evt.deviceId,
-                "THERMOSTAT_SMART_THINGS",
-                evt.value
-        )
-    }
-}
-
-def waterHandler(evt) {
-    if (evt.isStateChanged()) {
-        sendPushEvent(evt.deviceId,
-                "WATER_SENSOR_SMART_THINGS",
-                evt.value
-        )
-    }
-}
-
-def motionHandler(evt) {
-    if ("active" == evt.value) {
-        sendPushEvent(evt.deviceId,
-                "MOTION_SENSOR_SMART_THINGS",
-                evt.value)
-    }
-}
-
-def switchHandler(evt) {
-    log.debug "$evt.deviceId switch changed state to $evt.value"
-}
-
-def getDevices() {
-    def resp = []
-    switches.each {
-        resp << extractSwitch(it)
-    }
-    motionSensors.each {
-        resp << extractMotionSensor(it)
-    }
-
-    lamps.each {
-        resp << extractLamp(it)
-    }
-
-    thermostats.each {
-        resp << extractThermostat(it)
-    }
-
-    return resp
-}
-
-def getDevice() {
-    def id = params.id
-    log.info "Getting device by id " + id
-    def device = findDeviceById(id);
-    if (device == null) {
-        httpError(400, "$id is not a valid id for switch specified")
-    } else if (device.type == "SWITCH_SMART_THINGS") {
-        return extractSwitch(device.device);
-    } else if (device.type == "THERMOSTAT_SMART_THINGS") {
-        return extractThermostat(device.device);
-    } else if (device.type == "LAMP_SMART_THINGS") {
-        return extractLamp(device.device);
-    } else if (device.type == "MOTION_SENSOR_SMART_THINGS") {
-        return extractMotionSensor(device.device);
-    }
-    return nil
-}
-
-void updateDevice() {
-    def id = params.id
-    def device = findDeviceById(id)
-
-    if (device == null) {
-        httpError(400, "$id is not a valid switch id")
-    } else if (device.type == "SWITCH_SMART_THINGS") {
-        changeSwitchState(device, request.JSON?.powered)
-    } else if (device.type == "THERMOSTAT_SMART_THINGS") {
-        def heating_setpoint = request.JSON?.heating_setpoint
-        def cooling_setpoint = request.JSON?.cooling_setpoint
-        def thermostat_setpoint = request.JSON?.thermostat_setpoint
-        if (heating_setpoint != null) {
-            device.device.setHeatingSetpoint(heating_setpoint)
-        }
-        if (cooling_setpoint != null) {
-            device.device.setCoolingSetpoint(cooling_setpoint)
-        }
-        //if (thermostat_setpoint != null) {
-        //	device.device.setThermostatSetpoint(thermostat_setpoint)
-        //}
-    } else if (device.type == "LAMP_SMART_THINGS") {
-        def powered = request.JSON?.powered
-        def color_h = request.JSON?.color_h
-        def color_s = request.JSON?.color_s
-        def color_b = request.JSON?.color_b
-        def color_temperature = request.JSON?.color_temperature
-        if (powered != null) {
-            changeSwitchState(device, request.JSON?.powered)
-        }
-        if (color_h != null) {
-            device.device.setHue(color_h)
-        }
-        if (color_b != null) {
-            device.device.setLevel(color_b)
-        }
-        if (color_s != null) {
-            device.device.setSaturation(color_s)
-        }
-        if (color_temperature != null) {
-            device.device.setColorTemperature(color_temperature)
-        }
-    } else if (device.type == "MOTION_SENSOR_SMART_THINGS") {
-        httpError(400, "Unable to control motion sensor")
-    }
-}
-
-def findDeviceById(id) {
-    def device = switches.find { it.id == id }
-    def type = "SWITCH_SMART_THINGS"
-    if (device == null) {
-        device = thermostats.find { it.id == id }
-        type = "THERMOSTAT_SMART_THINGS"
-    }
-    if (device == null) {
-        device = lamps.find { it.id == id }
-        type = "LAMP_SMART_THINGS"
-    }
-    if (device == null) {
-        device = motionSensors.find { it.id == id }
-        type = "MOTION_SENSOR_SMART_THINGS"
-    }
-    if (device == null) {
-        return null;
-    }
-    return [device: device, type: type];
-}
-
-
-def extractSwitch(it) {
-    return [id: it.id, type: "SWITCH_SMART_THINGS", state: [name: it.displayName, powered: it.currentValue("switch") == "on" ? true : false]]
-}
-
-def extractMotionSensor(it) {
-    return [id: it.id, type: "MOTION_SENSOR_SMART_THINGS", state: [name: it.displayName, state: it.currentValue("motion")]]
-}
-
-def extractLamp(it) {
-    return [id: it.id, type: "LAMP_SMART_THINGS", state: [name             : it.displayName,
-                                                          color_h          : it.currentValue("hue"), color_s: it.currentValue("saturation"), color_b: it.currentValue("level"),
-                                                          color_temperature: it.currentValue("colorTemperature"), powered: it.currentValue("switch") == "on" ? true : false]]
-}
-
-def extractThermostat(it) {
-    return [id: it.id, type: "THERMOSTAT_SMART_THINGS", state: [name                      : it.displayName,
-                                                                temperature               : it.currentValue("temperature"),
-                                                                heating_setpoint          : it.currentValue("heatingSetpoint"),
-                                                                cooling_setpoint          : it.currentValue("coolingSetpoint"),
-                                                                thermostat_setpoint       : it.currentValue("thermostatSetpoint"),
-                                                                thermostat_mode           : it.currentValue("thermostatMode"),
-                                                                thermostat_fan_mode       : it.currentValue("thermostatFanMode"),
-                                                                thermostat_operating_state: it.currentValue("thermostatOperatingState")]]
-}
-
-def changeSwitchState(device, powered) {
-    log.info "Updating device " + device.device.displayName + " to state $powered"
-    switch (powered) {
-        case "true":
-            device.device.on()
-            break
-        case "false":
-            device.device.off()
-            break
-        default:
-            httpError(400, "$powered is not a valid power state for switch specified")
-    }
-}
-
-def sendPushEvent(pushEvent) {
-    def params = [
-            uri               : "https://intent-processor-stage.cubic.ai/api/v1/pushEvent",
-            headers           : [
-                    Authorization: "Bearer -gm-IOuQR3W2Gim8Tjwsuw",
-                    Accept       : "/"
-            ],
-            body              : pushEvent,
-            requestContentType: "application/json"
-    ]
-    try {
-        httpPost(params) { resp ->
-            log.debug "response data: ${resp.data}"
-            log.debug "response contentType: ${resp.contentType}"
-        }
-    } catch (e) {
-        log.debug "something went wrong: $e"
-    }
-}
-
-def sendPushEvent(id, type, state) {
-    sendPushEvent(
-            [device_id  : id,
-             device_type: type,
-             state      : state]
-    )
-}

smartapps/smartthings/life360-connect.src/life360-connect.groovy

@@ -289,12 +289,12 @@ def initializeLife360Connection() {
        		state.life360AccessToken = result.data.access_token
             return true;
    		}
-		log.debug "Response=${result.data}"
+		log.info "Life360 initializeLife360Connection, response=${result.data}"
         return false;
         
     }
     catch (e) {
-       log.debug e
+       log.error "Life360 initializeLife360Connection, error: $e"
        return false;
     }
 
@@ -656,7 +656,7 @@ def generateInitialEvent (member, childDevice) {
     
     try { // we are going to just ignore any errors
     
-    	log.debug "Generate Initial Event for New Device for Member = ${member.id}"
+    	log.info "Life360 generateInitialEvent($member, $childDevice)"
         
         def place = state.places.find{it.id==settings.place}
         
@@ -678,6 +678,8 @@ def generateInitialEvent (member, childDevice) {
   
   			boolean isPresent = (distanceAway <= placeRadius)
 
+			log.info "Life360 generateInitialEvent, member: ($memberLatitude, $memberLongitude), place: ($placeLatitude, $placeLongitude), radius: $placeRadius, dist: $distanceAway, present: $isPresent"
+                
         	// log.debug "External Id=${app.id}:${member.id}"
         
        		// def childDevice2 = getChildDevice("${app.id}.${member.id}")
@@ -718,7 +720,7 @@ def haversine(lat1, lon1, lat2, lon2) {
 
 def placeEventHandler() {
 
-	log.debug "In placeEventHandler method."
+	log.info "Life360 placeEventHandler: params=$params, settings.place=$settings.place"
 
 	// the POST to this end-point will look like:
     // POST http://test.com/webhook?circleId=XXXX&placeId=XXXX&userId=XXXX&direction=arrive
@@ -729,8 +731,6 @@ def placeEventHandler() {
     def direction = params?.direction
     def timestamp = params?.timestamp
     
-    log.debug "Life360 Event: Circle: ${circleId}, Place: ${placeId}, User: ${userId}, Direction: ${direction}"
-
     if (placeId == settings.place) {
 
 		def presenceState = (direction=="in")
@@ -745,10 +745,10 @@ def placeEventHandler() {
 
 		if (deviceWrapper) {
 			deviceWrapper.generatePresenceEvent(presenceState)
-    		log.debug "Event raised on child device: ${externalId}"
+    		log.debug "Life360 event raised on child device: ${externalId}"
 		}
    		else {
-    		log.debug "Couldn't find child device associated with inbound Life360 event."
+    		log.warn "Life360 couldn't find child device associated with inbound Life360 event."
     	}
     }