MSA-1695: This is an adaptation of standard smartthings Dimmer to be used with Fibaro Roller Shutter 2 (model FGR-222, firmware 2.5).

[CHF-487] Health Check for Z-Wave Dimmer Switch

devicetypes/adf/fibaro-roller-shutter.src/fibaro-roller-shutter.groovy

@@ -0,0 +1,345 @@
+/**
+ *  Device Type Definition File
+ *
+ *  Device Type:		Fibaro Roller Shutter
+ *  File Name:			fibaro-roller-shutter.groovy
+ *	Initial Release:	2015-06-00
+ *	Author:				SmartThings
+ *
+ *  Copyright 2015 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+
+metadata {
+	// Automatically generated. Make future change here.
+	definition (name: "Fibaro Roller Shutter", namespace: "ADF", author: "ADF") {
+		capability "Switch Level"
+		capability "Actuator"
+		capability "Switch"
+		capability "Polling"
+		capability "Refresh"
+		capability "Sensor"
+                        
+        command		"resetParams2StDefaults"
+        command		"listCurrentParams"
+        command		"updateZwaveParam"
+
+        fingerprint deviceId: "0x1101", inClusters: "0x72,0x86,0x70,0x85,0x8E,0x26,0x7A,0x27,0x73,0xEF,0x26,0x2B"
+	}
+
+	simulator {
+		status "on":  "command: 2003, payload: FF"
+		status "off": "command: 2003, payload: 00"
+		status "09%": "command: 2003, payload: 09"
+		status "10%": "command: 2003, payload: 0A"
+		status "33%": "command: 2003, payload: 21"
+		status "66%": "command: 2003, payload: 42"
+		status "99%": "command: 2003, payload: 63"
+
+		// reply messages
+		reply "2001FF,delay 5000,2602": "command: 2603, payload: FF"
+		reply "200100,delay 5000,2602": "command: 2603, payload: 00"
+		reply "200119,delay 5000,2602": "command: 2603, payload: 19"
+		reply "200132,delay 5000,2602": "command: 2603, payload: 32"
+		reply "20014B,delay 5000,2602": "command: 2603, payload: 4B"
+		reply "200163,delay 5000,2602": "command: 2603, payload: 63"
+	}
+
+	tiles {
+            multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true) {
+            tileAttribute("device.switch", key: "PRIMARY_CONTROL") {
+                attributeState("on", label:"open", action:"switch.off", icon:"st.doors.garage.garage-open", backgroundColor:"#79b821", nextState: "turningOff")
+				attributeState("off", label:"close", action:"switch.on", icon:"st.doors.garage.garage-closed", backgroundColor:"#ffffff", nextState: "turningOn")
+                attributeState("turningOn", label:"opening", action:"switch.off", icon:"st.doors.garage.garage-opening", backgroundColor:"#79b821", nextState: "turningOff")
+                attributeState("turningOff", label:"closing", action:"switch.on", icon:"st.doors.garage.garage-closing", backgroundColor:"#ffffff", nextState:"turningOn")
+            }
+            tileAttribute ("device.level", key: "SLIDER_CONTROL") {
+                attributeState("level", action:"switch level.setLevel")
+            }
+        }
+		standardTile("refresh", "device.switch", width: 2, height: 2, inactiveLabel: false, decoration: "flat") {
+			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
+		}
+        standardTile("on", "device.switch", width: 2, height: 2, inactiveLabel: false, decoration: "flat") {
+            state("on", label:'open', action:"switch.on", icon:"st.doors.garage.garage-opening")
+        	}
+        standardTile("off", "device.switch", width: 2, height: 2, inactiveLabel: false, decoration: "flat") {
+            state("off", label:'close', action:"switch.off", icon:"st.doors.garage.garage-closing")
+        	}
+        standardTile("stop", "device.level", width: 2, height: 2, inactiveLabel: false, decoration: "flat") {
+            state("default", label:'stop/my', action:"switch level.setLevel", icon:"st.Transportation.transportation13")
+        	}
+            
+		main(["switch"])
+		details(["switch", "refresh", "on", "off", "stop"])
+	}
+}
+
+def parse(String description) {
+	def item1 = [
+		canBeCurrentState: false,
+		linkText: getLinkText(device),
+		isStateChange: false,
+		displayed: false,
+		descriptionText: description,
+		value:  description
+	]
+	def result
+	def cmd = zwave.parse(description, [0x26: 1, 0x70: 2, 072: 2])
+    //log.debug "cmd: ${cmd}"
+    
+    if (cmd) {
+        result = createEvent(cmd, item1)
+	}
+	else {
+		item1.displayed = displayed(description, item1.isStateChange)
+		result = [item1]
+	}
+    
+    if(result?.descriptionText)
+		log.debug "Parse returned ${result?.descriptionText}"
+        
+	result
+
+}
+
+def createEvent(physicalgraph.zwave.commands.basicv1.BasicReport cmd, Map item1) {
+	def result = doCreateEvent(cmd, item1)
+	for (int i = 0; i < result.size(); i++) {
+		result[i].type = "physical"
+	}
+	result
+}
+
+def createEvent(physicalgraph.zwave.commands.basicv1.BasicSet cmd, Map item1) {
+	def result = doCreateEvent(cmd, item1)
+	for (int i = 0; i < result.size(); i++) {
+		result[i].type = "physical"
+	}
+	result
+}
+
+def createEvent(physicalgraph.zwave.commands.switchmultilevelv1.SwitchMultilevelStartLevelChange cmd, Map item1) {
+	[]
+}
+
+def createEvent(physicalgraph.zwave.commands.switchmultilevelv1.SwitchMultilevelStopLevelChange cmd, Map item1) {
+	[response(zwave.basicV1.basicGet())]
+}
+
+def createEvent(physicalgraph.zwave.commands.switchmultilevelv1.SwitchMultilevelSet cmd, Map item1) {
+	def result = doCreateEvent(cmd, item1)
+	for (int i = 0; i < result.size(); i++) {
+		result[i].type = "physical"
+	}
+	result
+}
+
+def createEvent(physicalgraph.zwave.commands.switchmultilevelv1.SwitchMultilevelReport cmd, Map item1) {
+	def result = doCreateEvent(cmd, item1)
+	result[0].descriptionText = "${item1.linkText} is ${item1.value}"
+	result[0].handlerName = cmd.value ? "statusOn" : "statusOff"
+	for (int i = 0; i < result.size(); i++) {
+		result[i].type = "digital"
+	}
+	result
+}
+
+def doCreateEvent(physicalgraph.zwave.Command cmd, Map item1) {
+	def result = [item1]
+
+	item1.name = "switch"
+	item1.value = cmd.value ? "on" : "off"
+	item1.handlerName = item1.value
+	item1.descriptionText = "${item1.linkText} was turned ${item1.value}"
+	item1.canBeCurrentState = true
+	item1.isStateChange = isStateChange(device, item1.name, item1.value)
+	item1.displayed = item1.isStateChange
+
+	if (cmd.value >= 5) {
+		def item2 = new LinkedHashMap(item1)
+		item2.name = "level"
+		item2.value = cmd.value as String
+		item2.unit = "%"
+		item2.descriptionText = "${item1.linkText} dimmed ${item2.value} %"
+		item2.canBeCurrentState = true
+		item2.isStateChange = isStateChange(device, item2.name, item2.value)
+		item2.displayed = false
+		result << item2
+	}
+	result
+}
+
+def createEvent(physicalgraph.zwave.Command cmd,  Map map) {
+	// Handles any Z-Wave commands we aren't interested in
+	log.debug "UNHANDLED COMMAND $cmd"
+}
+
+def on() {
+	log.info "on"
+	delayBetween([zwave.basicV1.basicSet(value: 0xFF).format(), zwave.switchMultilevelV1.switchMultilevelGet().format()], 5000)
+}
+
+def off() {
+	delayBetween ([zwave.basicV1.basicSet(value: 0x00).format(), zwave.switchMultilevelV1.switchMultilevelGet().format()], 5000)
+}
+
+def setLevel(value) {
+    def level = Math.min(value as Integer, 99)
+	delayBetween ([zwave.basicV1.basicSet(value: level).format(), zwave.switchMultilevelV1.switchMultilevelGet().format()], 5000)
+}
+
+def setLevel(value, duration) {
+    def level = Math.min(value as Integer, 99)
+	def dimmingDuration = duration < 128 ? duration : 128 + Math.round(duration / 60)
+	zwave.switchMultilevelV2.switchMultilevelSet(value: level, dimmingDuration: dimmingDuration).format()
+}
+
+def poll() {
+	zwave.switchMultilevelV1.switchMultilevelGet().format()
+}
+
+def refresh() {
+	zwave.switchMultilevelV1.switchMultilevelGet().format()
+}
+
+ /**
+ * Configures the device to settings needed by SmarthThings at device discovery time. Assumes
+ * device is already at default parameter settings.
+ *
+ * @param none
+ *
+ * @return none
+ */
+def configure() {
+	log.debug "Configuring Device..."
+	def cmds = []
+
+	// send associate to group 3 to get sensor data reported only to hub
+	cmds << zwave.associationV2.associationSet(groupingIdentifier:3, nodeId:[zwaveHubNodeId]).format()
+
+
+	delayBetween(cmds, 500)
+}
+
+
+def createEvent(physicalgraph.zwave.commands.configurationv2.ConfigurationReport cmd, Map item1) {
+
+	log.debug "${device.displayName} parameter '${cmd.parameterNumber}' with a byte size of '${cmd.size}' is set to '${cmd.configurationValue}'"
+
+}
+
+ /**
+ * This method will allow the user to update device parameters (behavior) from an app.
+ * the user can write his/her own app to envoke this method. 
+ * No type or value checking is done to compare to what device capability or reaction.
+ * It is up to user to read OEM documentation prio to envoking this method.
+ * 
+ * <p>THIS IS AN ADVANCED OPERATION. USE AT YOUR OWN RISK! READ OEM DOCUMENTATION!
+ *
+ * @param List[paramNumber:80,value:10,size:1]
+ *
+ *
+ * @return none
+ */
+def updateZwaveParam(params) {
+	if ( params ) {
+        def pNumber = params.paramNumber
+        def pSize	= params.size
+        def pValue	= [params.value]
+        log.debug "Make sure device is awake and in recieve mode"
+        log.debug "Updating ${device.displayName} parameter number '${pNumber}' with value '${pValue}' with size of '${pSize}'"
+
+		def cmds = []
+        cmds << zwave.configurationV1.configurationSet(configurationValue: pValue, parameterNumber: pNumber, size: pSize).format()
+        cmds << zwave.configurationV1.configurationGet(parameterNumber: pNumber).format()
+        delayBetween(cmds, 1000)        
+    }
+}
+
+ /**
+ * Sets all of available Fibaro parameters back to the device defaults except for what
+ * SmartThings needs to support the stock functionality as released. 
+ *
+ * <p>THIS IS AN ADVANCED OPERATION. USE AT YOUR OWN RISK! READ OEM DOCUMENTATION!
+ *
+ * @param none
+ *
+ * @return none
+ */
+def resetParams2StDefaults() {
+	log.debug "Resetting ${device.displayName} parameters to SmartThings compatible defaults"
+	def cmds = []
+	cmds << zwave.configurationV1.configurationSet(configurationValue: [255], parameterNumber: 1,  size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [0],   parameterNumber: 6,  size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [1],   parameterNumber: 7,  size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [1],   parameterNumber: 8,  size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [5],   parameterNumber: 9,  size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [1],   parameterNumber: 10, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [1],   parameterNumber: 11, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [99],  parameterNumber: 12, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [2],   parameterNumber: 13, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [0],   parameterNumber: 14, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [1],   parameterNumber: 15, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [1],   parameterNumber: 16, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [0],   parameterNumber: 17, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [0],   parameterNumber: 18, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [0],   parameterNumber: 19, size: 1).format()
+    //Param 20 is different for 50Hz or 60 Hz uncomment the line that will reflect the power frequency used
+    //cmds << zwave.configurationV1.configurationSet(configurationValue: [101],   parameterNumber: 20, size: 1).format() //60 Hz (US)
+    //cmds << zwave.configurationV1.configurationSet(configurationValue: [110],   parameterNumber: 20, size: 1).format() //50 Hz (UK)
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [3],   parameterNumber: 30, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [600],   parameterNumber: 39, size: 1).format()
+    //Param 40 not needed by SmartThings
+    //cmds << zwave.configurationV1.configurationSet(configurationValue: [0],   parameterNumber: 40, size: 1).format()
+    cmds << zwave.configurationV1.configurationSet(configurationValue: [0],   parameterNumber: 41, size: 1).format()
+    
+    delayBetween(cmds, 500)
+}
+
+ /**
+ * Lists all of available Fibaro parameters and thier current settings out to the 
+ * logging window in the IDE. This will be called from the "Fibaro Tweaker" or 
+ * user's own app.
+ *
+ * <p>THIS IS AN ADVANCED OPERATION. USE AT YOUR OWN RISK! READ OEM DOCUMENTATION!
+ *
+ * @param none
+ *
+ * @return none
+ */
+def listCurrentParams() {
+	log.debug "Listing of current parameter settings of ${device.displayName}"
+    def cmds = []
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 1).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 6).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 7).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 8).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 9).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 10).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 11).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 12).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 13).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 14).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 15).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 16).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 17).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 18).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 19).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 20).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 30).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 39).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 40).format()
+    cmds << zwave.configurationV1.configurationGet(parameterNumber: 41).format()
+    
+	delayBetween(cmds, 500)
+}

devicetypes/smartthings/dimmer-switch.src/dimmer-switch.groovy

@@ -22,9 +22,10 @@ metadata {
 		capability "Sensor"
 		capability "Health Check"
 
-		fingerprint mfr:"0063", prod:"4457", deviceJoinName: "Z-Wave Wall Dimmer"
+		fingerprint mfr:"0063", prod:"4457", deviceJoinName: "GE In-Wall Smart Dimmer "
-		fingerprint mfr:"0063", prod:"4944", deviceJoinName: "Z-Wave Wall Dimmer"
+		fingerprint mfr:"0063", prod:"4944", deviceJoinName: "GE In-Wall Smart Dimmer "
-		fingerprint mfr:"0063", prod:"5044", deviceJoinName: "Z-Wave Plug-In Dimmer"
+		fingerprint mfr:"0063", prod:"5044", deviceJoinName: "GE Plug-In Smart Dimmer "
+		fingerprint mfr:"0063", prod:"4944", model:"3034", deviceJoinName: "GE In-Wall Smart Fan Control"
 	}
 
 	simulator {

devicetypes/smartthings/life360-user.src/life360-user.groovy

@@ -39,7 +39,7 @@ metadata {
 }
 
 def generatePresenceEvent(boolean present) {
-	log.debug "Here in generatePresenceEvent!"
+	log.info "Life360 generatePresenceEvent($present)"
 	def value = formatValue(present)
 	def linkText = getLinkText(device)
 	def descriptionText = formatDescriptionText(linkText, present)

devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy

@@ -128,7 +128,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07) {
 					if (cluster.data[0] == 0x00){
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"

devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy

@@ -132,7 +132,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07) {
 					if (cluster.data[0] == 0x00) {
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"

devicetypes/smartthings/smartsense-multi-sensor.src/smartsense-multi-sensor.groovy

@@ -161,7 +161,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07) {
 					if(cluster.data[0] == 0x00) {
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
@@ -339,7 +339,7 @@ private Map getContactResult(value) {
 	log.debug "Contact: ${device.displayName} value = ${value}"
 	def descriptionText = value == 'open' ? '{{ device.displayName }} was opened' : '{{ device.displayName }} was closed'
 	sendEvent(name: 'contact', value: value, descriptionText: descriptionText, displayed: false, translatable: true)
-	sendEvent(name: 'status', value: value, descriptionText: descriptionText, translatable: true)
+	return [name: 'status', value: value, descriptionText: descriptionText, translatable: true]
 }
 
 private getAccelerationResult(numValue) {

devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy

@@ -119,7 +119,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07){
 					if (cluster.data[0] == 0x00) {
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy

@@ -103,7 +103,7 @@ private Map parseCatchAllMessage(String description) {
 				if (cluster.command == 0x07) {
 					if (cluster.data[0] == 0x00){
 						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+						resultMap = [name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID]]
 					}
 					else {
 						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"

devicetypes/smartthings/zwave-dimmer-switch-generic.src/zwave-dimmer-switch-generic.groovy

@@ -24,6 +24,10 @@ metadata {
 		fingerprint inClusters: "0x26", deviceJoinName: "Z-Wave Dimmer"
 		fingerprint mfr:"001D", prod:"1902", deviceJoinName: "Z-Wave Dimmer"
 		fingerprint mfr:"001D", prod:"1B03", model:"0334", deviceJoinName: "Leviton Universal Dimmer"
+		fingerprint mfr:"011A", prod:"0102", model:"0201", deviceJoinName: "Enerwave In-Wall Dimmer"
+		fingerprint mfr:"001D", prod:"1001", model:"0334", deviceJoinName: "Leviton 3-Speed Fan Controller"
+		fingerprint mfr:"001D", prod:"0602", model:"0334", deviceJoinName: "Leviton Magnetic Low Voltage Dimmer"
+		fingerprint mfr:"001D", prod:"0401", model:"0334", deviceJoinName: "Leviton 600W Incandescent Dimmer"
 	}
 
 	simulator {

devicetypes/smartthings/zwave-switch-generic.src/zwave-switch-generic.groovy

@@ -25,6 +25,9 @@ metadata {
 		fingerprint mfr:"0063", prod:"4F50", model:"3031", deviceJoinName: "GE Plug-in Outdoor Switch"
 		fingerprint mfr:"001D", prod:"1D04", model:"0334", deviceJoinName: "Leviton Outlet"
 		fingerprint mfr:"001D", prod:"1C02", model:"0334", deviceJoinName: "Leviton Switch"
+		fingerprint mfr:"001D", prod:"0301", model:"0334", deviceJoinName: "Leviton 15A Switch"
+		fingerprint mfr:"011A", prod:"0101", model:"0102", deviceJoinName: "Enerwave On/Off Switch"
+		fingerprint mfr:"011A", prod:"0101", model:"0603", deviceJoinName: "Enerwave Duplex Receptacle"
 	}
 
 	// simulator metadata

smartapps/cubicrobotics/cubic-butler-for-smart-home.src/cubic-butler-for-smart-home.groovy

@@ -1,327 +0,0 @@
-/**
- *  Cubic Home
- * sdfssdfsfsdfsdfdsf
- *  Copyright 2016 Nikolay Zenovkin
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-definition(
-        name: "Cubic Butler for Smart Home",
-        namespace: "cubicrobotics",
-        author: "Cubic Robotics",
-        description: "Hey, I’m Cubic, AI butler for smart home! \n" +
-                "I am the one and only app you need to control an entire home. \n" +
-                "Right now I can help you to control your SmartThings devices via natural speech and dashboard.\n" +
-                "Speak naturally, don’t learn robot! My A.I. is designed for a smart home control.\n" +
-                "- You don’t have to remember exact commands and phrases.\n" +
-                "- I have memory, and every new request will be processed in the context of previous ones.\n" +
-                "- I can ask clarifying questions, if I’m not sure what you mean.",
-        category: "Convenience",
-        iconUrl: "https://lh3.googleusercontent.com/GX5BRhaFq22HpAEU6tD4JXvizlxWFuB9zjyZE39-pLpZvQvvUmVpWXa0v4-oaxz4tg=w300-rw",
-        iconX2Url: "https://lh3.googleusercontent.com/GX5BRhaFq22HpAEU6tD4JXvizlxWFuB9zjyZE39-pLpZvQvvUmVpWXa0v4-oaxz4tg=w300-rw",
-        iconX3Url: "https://lh3.googleusercontent.com/GX5BRhaFq22HpAEU6tD4JXvizlxWFuB9zjyZE39-pLpZvQvvUmVpWXa0v4-oaxz4tg=w300-rw",
-        oauth: [displayName: "Cubic Home", displayLink: "http://cubic.ai/"])
-
-
-preferences {
-    section("Welcome to Cubic") {
-        // TODO: put inputs here
-    }
-    section("Allow Cubic to control these switches") {
-        input "switches", "capability.switch", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these motion sensors") {
-        input "motionSensors", "capability.motionSensor", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these bulbs") {
-        input "lamps", "capability.colorControl", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these thermostats") {
-        input "thermostats", "capability.thermostat", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these water sensors") {
-        input "waterSensors", "capability.waterSensor", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these CO sensors") {
-        input "smokeSensors", "capability.carbonMonoxideDetector", multiple: true, required: false
-    }
-
-    section("Allow Cubic to control these door controls") {
-        input "doorControls", "capability.doorControl", multiple: true, required: false
-    }
-
-}
-
-
-mappings {
-    path("/devices") {
-        action:
-        [
-                GET: "getDevices"
-        ]
-    }
-    path("/devices/:id") {
-        action:
-        [
-                PUT: "updateDevice",
-                GET: "getDevice"
-        ]
-    }
-}
-
-def installed() {
-    log.debug "Installed with settings: ${settings}"
-
-    initialize()
-}
-
-def updated() {
-    log.debug "Updated with settings: ${settings}"
-
-    unsubscribe()
-    initialize()
-}
-
-def initialize() {
-    subscribe(motionSensors, "motion", motionHandler)
-    subscribe(switches, "switch", switchHandler)
-    subscribe(thermostats, "thermostat.temperature", thermostatHandler)
-    subscribe(waterSensors, "waterSensor", waterHandler)
-    subscribe(smokeSensors, "carbonMonoxideDetector", smokeHandler)
-    subscribe(doorControls, "doorControl", doorControlHandler)
-}
-
-def doorControlHandler(evt) {
-    if (evt.isStateChanged()) {
-        sendPushEvent(evt.deviceId,
-                "DOOR_CONTROL_SMART_THINGS",
-                evt.value
-        )
-    }
-}
-
-def smokeHandler(evt) {
-    if (evt.isStateChanged()) {
-        sendPushEvent(evt.deviceId,
-                "SMOKE_CO_SENSOR_SMART_THINGS",
-                evt.value
-        )
-    }
-}
-
-def thermostatHandler(evt) {
-    if (evt.isStateChanged()) {
-        sendPushEvent(evt.deviceId,
-                "THERMOSTAT_SMART_THINGS",
-                evt.value
-        )
-    }
-}
-
-def waterHandler(evt) {
-    if (evt.isStateChanged()) {
-        sendPushEvent(evt.deviceId,
-                "WATER_SENSOR_SMART_THINGS",
-                evt.value
-        )
-    }
-}
-
-def motionHandler(evt) {
-    if ("active" == evt.value) {
-        sendPushEvent(evt.deviceId,
-                "MOTION_SENSOR_SMART_THINGS",
-                evt.value)
-    }
-}
-
-def switchHandler(evt) {
-    log.debug "$evt.deviceId switch changed state to $evt.value"
-}
-
-def getDevices() {
-    def resp = []
-    switches.each {
-        resp << extractSwitch(it)
-    }
-    motionSensors.each {
-        resp << extractMotionSensor(it)
-    }
-
-    lamps.each {
-        resp << extractLamp(it)
-    }
-
-    thermostats.each {
-        resp << extractThermostat(it)
-    }
-
-    return resp
-}
-
-def getDevice() {
-    def id = params.id
-    log.info "Getting device by id " + id
-    def device = findDeviceById(id);
-    if (device == null) {
-        httpError(400, "$id is not a valid id for switch specified")
-    } else if (device.type == "SWITCH_SMART_THINGS") {
-        return extractSwitch(device.device);
-    } else if (device.type == "THERMOSTAT_SMART_THINGS") {
-        return extractThermostat(device.device);
-    } else if (device.type == "LAMP_SMART_THINGS") {
-        return extractLamp(device.device);
-    } else if (device.type == "MOTION_SENSOR_SMART_THINGS") {
-        return extractMotionSensor(device.device);
-    }
-    return nil
-}
-
-void updateDevice() {
-    def id = params.id
-    def device = findDeviceById(id)
-
-    if (device == null) {
-        httpError(400, "$id is not a valid switch id")
-    } else if (device.type == "SWITCH_SMART_THINGS") {
-        changeSwitchState(device, request.JSON?.powered)
-    } else if (device.type == "THERMOSTAT_SMART_THINGS") {
-        def heating_setpoint = request.JSON?.heating_setpoint
-        def cooling_setpoint = request.JSON?.cooling_setpoint
-        def thermostat_setpoint = request.JSON?.thermostat_setpoint
-        if (heating_setpoint != null) {
-            device.device.setHeatingSetpoint(heating_setpoint)
-        }
-        if (cooling_setpoint != null) {
-            device.device.setCoolingSetpoint(cooling_setpoint)
-        }
-        //if (thermostat_setpoint != null) {
-        //	device.device.setThermostatSetpoint(thermostat_setpoint)
-        //}
-    } else if (device.type == "LAMP_SMART_THINGS") {
-        def powered = request.JSON?.powered
-        def color_h = request.JSON?.color_h
-        def color_s = request.JSON?.color_s
-        def color_b = request.JSON?.color_b
-        def color_temperature = request.JSON?.color_temperature
-        if (powered != null) {
-            changeSwitchState(device, request.JSON?.powered)
-        }
-        if (color_h != null) {
-            device.device.setHue(color_h)
-        }
-        if (color_b != null) {
-            device.device.setLevel(color_b)
-        }
-        if (color_s != null) {
-            device.device.setSaturation(color_s)
-        }
-        if (color_temperature != null) {
-            device.device.setColorTemperature(color_temperature)
-        }
-    } else if (device.type == "MOTION_SENSOR_SMART_THINGS") {
-        httpError(400, "Unable to control motion sensor")
-    }
-}
-
-def findDeviceById(id) {
-    def device = switches.find { it.id == id }
-    def type = "SWITCH_SMART_THINGS"
-    if (device == null) {
-        device = thermostats.find { it.id == id }
-        type = "THERMOSTAT_SMART_THINGS"
-    }
-    if (device == null) {
-        device = lamps.find { it.id == id }
-        type = "LAMP_SMART_THINGS"
-    }
-    if (device == null) {
-        device = motionSensors.find { it.id == id }
-        type = "MOTION_SENSOR_SMART_THINGS"
-    }
-    if (device == null) {
-        return null;
-    }
-    return [device: device, type: type];
-}
-
-
-def extractSwitch(it) {
-    return [id: it.id, type: "SWITCH_SMART_THINGS", state: [name: it.displayName, powered: it.currentValue("switch") == "on" ? true : false]]
-}
-
-def extractMotionSensor(it) {
-    return [id: it.id, type: "MOTION_SENSOR_SMART_THINGS", state: [name: it.displayName, state: it.currentValue("motion")]]
-}
-
-def extractLamp(it) {
-    return [id: it.id, type: "LAMP_SMART_THINGS", state: [name             : it.displayName,
-                                                          color_h          : it.currentValue("hue"), color_s: it.currentValue("saturation"), color_b: it.currentValue("level"),
-                                                          color_temperature: it.currentValue("colorTemperature"), powered: it.currentValue("switch") == "on" ? true : false]]
-}
-
-def extractThermostat(it) {
-    return [id: it.id, type: "THERMOSTAT_SMART_THINGS", state: [name                      : it.displayName,
-                                                                temperature               : it.currentValue("temperature"),
-                                                                heating_setpoint          : it.currentValue("heatingSetpoint"),
-                                                                cooling_setpoint          : it.currentValue("coolingSetpoint"),
-                                                                thermostat_setpoint       : it.currentValue("thermostatSetpoint"),
-                                                                thermostat_mode           : it.currentValue("thermostatMode"),
-                                                                thermostat_fan_mode       : it.currentValue("thermostatFanMode"),
-                                                                thermostat_operating_state: it.currentValue("thermostatOperatingState")]]
-}
-
-def changeSwitchState(device, powered) {
-    log.info "Updating device " + device.device.displayName + " to state $powered"
-    switch (powered) {
-        case "true":
-            device.device.on()
-            break
-        case "false":
-            device.device.off()
-            break
-        default:
-            httpError(400, "$powered is not a valid power state for switch specified")
-    }
-}
-
-def sendPushEvent(pushEvent) {
-    def params = [
-            uri               : "https://intent-processor-stage.cubic.ai/api/v1/pushEvent",
-            headers           : [
-                    Authorization: "Bearer -gm-IOuQR3W2Gim8Tjwsuw",
-                    Accept       : "/"
-            ],
-            body              : pushEvent,
-            requestContentType: "application/json"
-    ]
-    try {
-        httpPost(params) { resp ->
-            log.debug "response data: ${resp.data}"
-            log.debug "response contentType: ${resp.contentType}"
-        }
-    } catch (e) {
-        log.debug "something went wrong: $e"
-    }
-}
-
-def sendPushEvent(id, type, state) {
-    sendPushEvent(
-            [device_id  : id,
-             device_type: type,
-             state      : state]
-    )
-}

smartapps/smartthings/life360-connect.src/life360-connect.groovy

@@ -289,12 +289,12 @@ def initializeLife360Connection() {
        		state.life360AccessToken = result.data.access_token
             return true;
    		}
-		log.debug "Response=${result.data}"
+		log.info "Life360 initializeLife360Connection, response=${result.data}"
         return false;
         
     }
     catch (e) {
-       log.debug e
+       log.error "Life360 initializeLife360Connection, error: $e"
        return false;
     }
 
@@ -656,7 +656,7 @@ def generateInitialEvent (member, childDevice) {
     
     try { // we are going to just ignore any errors
     
-    	log.debug "Generate Initial Event for New Device for Member = ${member.id}"
+    	log.info "Life360 generateInitialEvent($member, $childDevice)"
         
         def place = state.places.find{it.id==settings.place}
         
@@ -677,6 +677,8 @@ def generateInitialEvent (member, childDevice) {
         	// log.debug "Distance Away = ${distanceAway}"
   
   			boolean isPresent = (distanceAway <= placeRadius)
+
+			log.info "Life360 generateInitialEvent, member: ($memberLatitude, $memberLongitude), place: ($placeLatitude, $placeLongitude), radius: $placeRadius, dist: $distanceAway, present: $isPresent"
                 
         	// log.debug "External Id=${app.id}:${member.id}"
         
@@ -718,7 +720,7 @@ def haversine(lat1, lon1, lat2, lon2) {
 
 def placeEventHandler() {
 
-	log.debug "In placeEventHandler method."
+	log.info "Life360 placeEventHandler: params=$params, settings.place=$settings.place"
 
 	// the POST to this end-point will look like:
     // POST http://test.com/webhook?circleId=XXXX&placeId=XXXX&userId=XXXX&direction=arrive
@@ -729,8 +731,6 @@ def placeEventHandler() {
     def direction = params?.direction
     def timestamp = params?.timestamp
     
-    log.debug "Life360 Event: Circle: ${circleId}, Place: ${placeId}, User: ${userId}, Direction: ${direction}"
-
     if (placeId == settings.place) {
 
 		def presenceState = (direction=="in")
@@ -745,10 +745,10 @@ def placeEventHandler() {
 
 		if (deviceWrapper) {
 			deviceWrapper.generatePresenceEvent(presenceState)
-    		log.debug "Event raised on child device: ${externalId}"
+    		log.debug "Life360 event raised on child device: ${externalId}"
 		}
    		else {
-    		log.debug "Couldn't find child device associated with inbound Life360 event."
+    		log.warn "Life360 couldn't find child device associated with inbound Life360 event."
     	}
     }