Revert "[CHF-590] Health Check smartalert-siren"

devicetypes/smartthings/smartalert-siren.src/.st-ignore

@@ -1,2 +0,0 @@
-.st-ignore
-README.md

devicetypes/smartthings/smartalert-siren.src/README.md

@@ -1,39 +0,0 @@
-# Smartalert Siren
-
-Cloud Execution
-
-Works with:
-
-* [FortrezZ Siren Strobe Alarm](https://www.smartthings.com/works-with-smartthings/other/fortrezz-water-valve)
-
-## Table of contents
-
-* [Capabilities](#capabilities)
-* [Health](#device-health)
-* [Troubleshooting](#troubleshooting)
-
-## Capabilities
-
-* **Actuator** - represents that a Device has commands
-* **Switch** - can detect state (possible values: on/off)
-* **Sensor** - detects sensor events
-* **Alarm** - allows for interacting with devices that serve as alarms
-* **Health Check** - indicates ability to get device health notifications
-
-## Device Health
-
-FortrezZ Siren Strobe Alarm is polled by the hub.
-As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
-Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
-Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
-the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
-it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
-
-* __32min__ checkInterval
-
-## Troubleshooting
-
-If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
-Pairing needs to be tried again by placing the device closer to the hub.
-Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
-* [FortrezZ Siren Strobe Alarm Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/202294760-FortrezZ-Siren-Strobe-Alarm)

devicetypes/smartthings/smartalert-siren.src/smartalert-siren.groovy

@@ -21,12 +21,10 @@ metadata {
 		capability "Switch"
 		capability "Sensor"
 		capability "Alarm"
-		capability "Health Check"
 
 		command "test"
 
 		fingerprint deviceId: "0x1100", inClusters: "0x26,0x71"
-		fingerprint mfr:"0084", prod:"0313", model:"010B", deviceJoinName: "FortrezZ Siren Strobe Alarm"
 	}
 
 	simulator {
@@ -70,16 +68,6 @@ metadata {
 	}
 }
 
-def installed() {
-// Device-Watch simply pings if no device events received for 32min(checkInterval)
-	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
-}
-
-def updated() {
-// Device-Watch simply pings if no device events received for 32min(checkInterval)
-	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
-}
-
 def on() {
 	[
 		zwave.basicV1.basicSet(value: 0xFF).format(),
@@ -161,10 +149,3 @@ def createEvents(physicalgraph.zwave.commands.basicv1.BasicReport cmd)
 def zwaveEvent(physicalgraph.zwave.Command cmd) {
 	log.warn "UNEXPECTED COMMAND: $cmd"
 }
-
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-	secure(zwave.basicV1.basicGet())
-}