MSA-1240: test

devicetypes/smartthings/cree-bulb.src/cree-bulb.groovy

@@ -13,19 +13,17 @@
  *  for the specific language governing permissions and limitations under the License.
  *
  */
-
-//@Deprecated: Moved to ZLL Dimmer Bulb
+ 
 metadata {
     definition (name: "Cree Bulb", namespace: "smartthings", author: "SmartThings") {
 
         capability "Actuator"
         capability "Configuration"
-        capability "Polling"
         capability "Refresh"
         capability "Switch"
         capability "Switch Level"
 
-        //fingerprint profileId: "C05E", inClusters: "0000,0003,0004,0005,0006,0008,1000", outClusters: "0000,0019"
+        fingerprint profileId: "C05E", inClusters: "0000,0003,0004,0005,0006,0008,1000", outClusters: "0000,0019"
     }
 
     // simulator metadata
@@ -90,10 +88,6 @@ def refresh() {
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig() + zigbee.levelConfig()
 }
 
-def poll() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh()
-}
-
 def configure() {
     log.debug "Configuring Reporting and Bindings."
     zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()

devicetypes/smartthings/test-arrival-sensor.src/test-arrival-sensor.groovy

@@ -0,0 +1,294 @@
+/**
+ *  Copyright 2015 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+metadata {
+	definition (name: "Test Arrival Sensor", namespace: "smartthings", author: "Mr.kim") {
+		capability "Tone"
+		capability "Actuator"
+		capability "Signal Strength"
+		capability "Presence Sensor"
+		capability "Sensor"
+		capability "Battery"
+
+		fingerprint profileId: "FC01", deviceId: "019A"
+		fingerprint profileId: "FC01", deviceId: "0131", inClusters: "0000,0003", outClusters: "0003"
+		fingerprint profileId: "FC01", deviceId: "0131", inClusters: "0000", outClusters: "0006"
+	}
+
+	simulator {
+		status "present": "presence: 1"
+		status "not present": "presence: 0"
+		status "battery": "battery: 27, batteryDivisor: 0A, rssi: 100, lqi: 64"
+	}
+
+	preferences {
+		section {
+			image(name: 'educationalcontent', multiple: true, images: [
+				"http://cdn.device-gse.smartthings.com/Arrival/Arrival1.jpg",
+				"http://cdn.device-gse.smartthings.com/Arrival/Arrival2.jpg"
+				])
+		}
+	}
+
+	tiles {
+		standardTile("presence", "device.presence", width: 2, height: 2, canChangeBackground: true) {
+			state "present", labelIcon:"st.presence.tile.present", backgroundColor:"#53a7c0"
+			state "not present", labelIcon:"st.presence.tile.not-present", backgroundColor:"#ebeef2"
+		}
+		standardTile("beep", "device.beep", decoration: "flat") {
+			state "beep", label:'', action:"tone.beep", icon:"st.secondary.beep", backgroundColor:"#ffffff"
+		}
+		valueTile("battery", "device.battery", decoration: "flat", inactiveLabel: false) {
+			state "battery", label:'${currentValue}% battery', unit:""/*, backgroundColors:[
+				[value: 5, color: "#BC2323"],
+				[value: 10, color: "#D04E00"],
+				[value: 15, color: "#F1D801"],
+				[value: 16, color: "#FFFFFF"]
+			]*/
+		}
+		/*
+		valueTile("lqi", "device.lqi", decoration: "flat", inactiveLabel: false) {
+			state "lqi", label:'${currentValue}% signal', unit:""
+		}
+		*/
+		
+		main "presence"
+		details(["presence", "beep", "battery"/*, "lqi"*/])
+	}
+}
+
+def beep() {
+	/*
+	You can make the speaker turn on for 0.5-second beeps by sending some CLI commands:
+
+		Command: send raw, wait 7, send raw, wait 7, send raw
+		Future: new packet type "st.beep"
+
+		raw 0xFC05 {15 0A 11 00 00 15 01}
+		send 0x2F7F 2 2
+
+	where "0xABCD" is the node ID of the Smart Tag, everything else above is a constant. Except
+	the "15 01" at the end of the first raw command, that sets the speaker's period (reciprocal
+	of frequency). You can play with this value up or down to experiment with loudness as the
+	loudness will be strongly dependent upon frequency and the enclosure that it's in. Note that
+	"15 01" represents the hex number 0x0115 so a lower frequency is "16 01" (longer period) and
+	a higher frequency is "14 01" (shorter period). Note that since the tag only checks its parent
+	for messages every 5 seconds (while at rest) or every 3 seconds (while in motion) it will take
+	up to this long from the time you send the message to the time you hear a sound.
+	*/
+
+	[
+		"raw 0xFC05 {15 0A 11 00 00 15 01}",
+		"delay 7000",
+		"raw 0xFC05 {15 0A 11 00 00 15 01}",
+		"delay 7000",
+		"raw 0xFC05 {15 0A 11 00 00 15 01}",
+		"delay 7000",
+		"raw 0xFC05 {15 0A 11 00 00 15 01}",
+		"delay 7000",
+		"raw 0xFC05 {15 0A 11 00 00 15 01}"
+	]
+}
+
+def parse(String description) {
+	def results
+	if (isBatteryMessage(description)) {
+		results = parseBatteryMessage(description)
+	}
+	else {
+		results = parsePresenceMessage(description)
+	}
+
+	log.debug "Parse returned $results.descriptionText"
+	results
+}
+
+private Map parsePresenceMessage(String description) {
+	def name = parseName(description)
+	def value = parseValue(description)
+	def linkText = getLinkText(device)
+	def descriptionText = parseDescriptionText(linkText, value, description)
+	def handlerName = getState(value)
+	def isStateChange = isStateChange(device, name, value)
+
+	def results = [
+		name: name,
+		value: value,
+		unit: null,
+		linkText: linkText,
+		descriptionText: descriptionText,
+		handlerName: handlerName,
+		isStateChange: isStateChange,
+		displayed: displayed(description, isStateChange)
+	]
+
+	results
+}
+
+private String parseName(String description) {
+	if (description?.startsWith("presence: ")) {
+		return "presence"
+	}
+	null
+}
+
+private String parseValue(String description) {
+	if (description?.startsWith("presence: "))
+	{
+		if (description?.endsWith("1"))
+		{
+			return "present"
+		}
+		else if (description?.endsWith("0"))
+		{
+			return "not present"
+		}
+	}
+
+	description
+}
+
+private parseDescriptionText(String linkText, String value, String description) {
+	switch(value) {
+		case "present": return "$linkText has arrived"
+		case "not present": return "$linkText has left"
+		default: return value
+	}
+}
+
+private getState(String value) {
+	def state = value
+	if (value == "present") {
+		state = "arrived"
+	}
+	else if (value == "not present") {
+		state = "left"
+	}
+
+	state
+}
+
+private Boolean isBatteryMessage(String description) {
+	// "raw:36EF1C, dni:36EF, battery:1B, rssi:, lqi:"
+	description ==~ /.*battery:.*rssi:.*lqi:.*/
+}
+
+private List parseBatteryMessage(String description) {
+	def results = []
+	def parts = description.split(',')
+	parts.each { part ->
+		part = part.trim()
+		if (part.startsWith('battery:')) {
+			def batteryResult = getBatteryResult(part, description)
+			if (batteryResult) {
+				results << batteryResult
+			}
+		}
+		else if (part.startsWith('rssi:')) {
+			def rssiResult = getRssiResult(part, description)
+			if (rssiResult) {
+				results << rssiResult
+			}
+		}
+		else if (part.startsWith('lqi:')) {
+			def lqiResult = getLqiResult(part, description)
+			if (lqiResult) {
+				results << lqiResult
+			}
+		}
+	}
+
+	results
+}
+
+private getBatteryResult(part, description) {
+	def batteryDivisor = description.split(",").find {it.split(":")[0].trim() == "batteryDivisor"} ? description.split(",").find {it.split(":")[0].trim() == "batteryDivisor"}.split(":")[1].trim() : null
+	def name = "battery"
+	def value = zigbee.parseSmartThingsBatteryValue(part, batteryDivisor)
+	def unit = "%"
+	def linkText = getLinkText(device)
+	def descriptionText = "$linkText battery was ${value}${unit}"
+	def isStateChange = isStateChange(device, name, value)
+
+	[
+		name: name,
+		value: value,
+		unit: unit,
+		linkText: linkText,
+		descriptionText: descriptionText,
+		handlerName: name,
+		isStateChange: isStateChange,
+		//displayed: displayed(description, isStateChange)
+		displayed: false
+	]
+}
+
+private getRssiResult(part, description) {
+	def name = "rssi"
+	def parts = part.split(":")
+	if (parts.size() != 2) return null
+
+	def valueString = parts[1].trim()
+	def valueInt = Integer.parseInt(valueString, 16)
+	def value = (valueInt - 128).toString()
+	def linkText = getLinkText(device)
+	def descriptionText = "$linkText was $value dBm"
+	def isStateChange = isStateChange(device, name, value)
+
+	[
+		name: name,
+		value: value,
+		unit: "dBm",
+		linkText: linkText,
+		descriptionText: descriptionText,
+		handlerName: null,
+		isStateChange: isStateChange,
+		//displayed: displayed(description, isStateChange)
+		displayed: false
+	]
+}
+
+/**
+ * Use LQI (Link Quality Indicator) as a measure of signal strength. The values
+ * are 0 to 255 (0x00 to 0xFF) and higher values represent higher signal
+ * strength. Return as a percentage of 255.
+ *
+ * Note: To make the signal strength indicator more accurate, we could combine
+ * LQI with RSSI.
+ */
+private getLqiResult(part, description) {
+	def name = "lqi"
+	def parts = part.split(":")
+	if (parts.size() != 2) return null
+
+	def valueString = parts[1].trim()
+	def valueInt = Integer.parseInt(valueString, 16)
+	def percentageOf = 255
+	def value = Math.round((valueInt / percentageOf * 100)).toString()
+	def unit = "%"
+	def linkText = getLinkText(device)
+	def descriptionText = "$linkText Signal (LQI) was ${value}${unit}"
+	def isStateChange = isStateChange(device, name, value)
+
+	[
+		name: name,
+		value: value,
+		unit: unit,
+		linkText: linkText,
+		descriptionText: descriptionText,
+		handlerName: null,
+		isStateChange: isStateChange,
+		//displayed: displayed(description, isStateChange)
+		displayed: false
+	]
+}

devicetypes/smartthings/zigbee-hue-bulb.src/zigbee-hue-bulb.groovy

@@ -11,9 +11,6 @@
  *  for the specific language governing permissions and limitations under the License.
  *
  */
-
-//@Deprecated - Moved to zll-rgbw-bulb
-
 /* Philips Hue (via Zigbee)
 
 Capabilities:
@@ -25,10 +22,10 @@ Capabilities:
   Sensor
   Switch
   Switch Level
-
+  
 Custom Commands:
   setAdjustedColor
-
+    
 */
 
 metadata {
@@ -44,7 +41,7 @@ metadata {
 
 		command "setAdjustedColor"
 
-		//fingerprint profileId: "C05E", inClusters: "0000,0003,0004,0005,0006,0008,0300,1000", outClusters: "0019"
+		fingerprint profileId: "C05E", inClusters: "0000,0003,0004,0005,0006,0008,0300,1000", outClusters: "0019"
 	}
 
 	// simulator metadata

devicetypes/smartthings/zigbee-rgbw-bulb.src/zigbee-rgbw-bulb.groovy

@@ -33,7 +33,6 @@ metadata {
         fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 RGBW", deviceJoinName: "OSRAM LIGHTIFY LED A19 RGBW"
         fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY BR RGBW", deviceJoinName: "OSRAM LIGHTIFY LED BR30 RGBW"
         fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY RT RGBW", deviceJoinName: "OSRAM LIGHTIFY LED RT 5/6 RGBW"
-        fingerprint profileId: "C05E", deviceId: "0220", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 1000", outClusters: "0019", manufacturer: "LDS", model: "ZLL-ColorTemperature", deviceJoinName: "LDS ZLL-ColorTemperature"
     }
 
     // UI tile definitions
@@ -142,4 +141,4 @@ def setHue(value) {
 def setSaturation(value) {
     def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
     zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500")      //payload-> sat value, transition time
-}
+}

devicetypes/smartthings/zll-dimmer-bulb.src/zll-dimmer-bulb.groovy

@@ -1,99 +0,0 @@
-/**
- *  Copyright 2016 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-
-metadata {
-    definition (name: "ZLL Dimmer Bulb", namespace: "smartthings", author: "SmartThings") {
-
-        capability "Actuator"
-        capability "Configuration"
-        capability "Polling"
-        capability "Refresh"
-        capability "Switch"
-        capability "Switch Level"
-
-        fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0000,0019"
-        fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0000,0019", manufacturer: "CREE", model: "Connected A-19 60W Equivalent", deviceJoinName: "Cree Connected Bulb"
-        fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Classic A60 W clear", deviceJoinName: "OSRAM LIGHTIFY LED Smart Connected Light"
-    }
-
-    // simulator metadata
-    simulator {
-        // status messages
-        status "on": "on/off: 1"
-        status "off": "on/off: 0"
-
-        // reply messages
-        reply "zcl on-off on": "on/off: 1"
-        reply "zcl on-off off": "on/off: 0"
-    }
-
-    // UI tile definitions
-    tiles(scale: 2) {
-        multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-            tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-                attributeState "on", label:'${name}', action:"switch.off", icon:"st.switches.light.on", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "off", label:'${name}', action:"switch.on", icon:"st.switches.light.off", backgroundColor:"#ffffff", nextState:"turningOn"
-                attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.switches.light.on", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.switches.light.off", backgroundColor:"#ffffff", nextState:"turningOn"
-            }
-            tileAttribute ("device.level", key: "SLIDER_CONTROL") {
-                attributeState "level", action:"switch level.setLevel"
-            }
-        }
-        standardTile("refresh", "device.switch", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-        }
-        main "switch"
-        details(["switch", "refresh"])
-    }
-}
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-    log.debug "description is $description"
-
-    def resultMap = zigbee.getEvent(description)
-    if (resultMap) {
-        sendEvent(resultMap)
-    }
-    else {
-        log.debug "DID NOT PARSE MESSAGE for description : $description"
-        log.debug zigbee.parseDescriptionAsMap(description)
-    }
-}
-
-def off() {
-    zigbee.off() + ["delay 1500"] + zigbee.onOffRefresh()
-}
-
-def on() {
-    zigbee.on() + ["delay 1500"] + zigbee.onOffRefresh()
-}
-
-def setLevel(value) {
-    zigbee.setLevel(value) + ["delay 1500"] + zigbee.levelRefresh()         //adding refresh because of ZLL bulb not conforming to send-me-a-report
-}
-
-def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh()
-}
-
-def poll() {
-    refresh()
-}
-
-def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()
-}

devicetypes/smartthings/zll-rgbw-bulb.src/zll-rgbw-bulb.groovy

@@ -1,150 +0,0 @@
-/**
- *  Copyright 2016 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-
-metadata {
-    definition (name: "ZLL RGBW Bulb", namespace: "smartthings", author: "SmartThings") {
-
-        capability "Actuator"
-        capability "Color Control"
-        capability "Color Temperature"
-        capability "Configuration"
-        capability "Polling"
-        capability "Refresh"
-        capability "Switch"
-        capability "Switch Level"
-
-        fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300", outClusters: "0019"
-        fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 1000", outClusters: "0019"
-        fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 1000", outClusters: "0019", "manufacturer":"OSRAM", "model":"Classic A60 RGBW", deviceJoinName: "OSRAM LIGHTIFY LED Classic A60 RGBW"
-    }
-
-    // UI tile definitions
-    tiles(scale: 2) {
-        multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-            tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-                attributeState "on", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "off", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
-                attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
-            }
-            tileAttribute ("device.level", key: "SLIDER_CONTROL") {
-                attributeState "level", action:"switch level.setLevel"
-            }
-            tileAttribute ("device.color", key: "COLOR_CONTROL") {
-                attributeState "color", action:"color control.setColor"
-            }
-        }
-        controlTile("colorTempSliderControl", "device.colorTemperature", "slider", width: 4, height: 2, inactiveLabel: false, range:"(2700..6500)") {
-            state "colorTemperature", action:"color temperature.setColorTemperature"
-        }
-        valueTile("colorTemp", "device.colorTemperature", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "colorTemperature", label: '${currentValue} K'
-        }
-        standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-        }
-
-        main(["switch"])
-        details(["switch", "colorTempSliderControl", "colorTemp", "refresh"])
-    }
-}
-
-//Globals
-private getATTRIBUTE_HUE() { 0x0000 }
-private getATTRIBUTE_SATURATION() { 0x0001 }
-private getHUE_COMMAND() { 0x00 }
-private getSATURATION_COMMAND() { 0x03 }
-private getCOLOR_CONTROL_CLUSTER() { 0x0300 }
-private getATTRIBUTE_COLOR_TEMPERATURE() { 0x0007 }
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-    log.debug "description is $description"
-
-    def finalResult = zigbee.getEvent(description)
-    if (finalResult) {
-        log.debug finalResult
-        sendEvent(finalResult)
-    }
-    else {
-        def zigbeeMap = zigbee.parseDescriptionAsMap(description)
-        log.trace "zigbeeMap : $zigbeeMap"
-
-        if (zigbeeMap?.clusterInt == COLOR_CONTROL_CLUSTER) {
-            if(zigbeeMap.attrInt == ATTRIBUTE_HUE){  //Hue Attribute
-                def hueValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 360)
-                sendEvent(name: "hue", value: hueValue, displayed:false)
-            }
-            else if(zigbeeMap.attrInt == ATTRIBUTE_SATURATION){ //Saturation Attribute
-                def saturationValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
-                sendEvent(name: "saturation", value: saturationValue, displayed:false)
-            }
-        }
-        else {
-            log.info "DID NOT PARSE MESSAGE for description : $description"
-        }
-    }
-}
-
-def on() {
-    zigbee.on() + ["delay 1500"] + zigbee.onOffRefresh()
-}
-
-def off() {
-    zigbee.off() + ["delay 1500"] + zigbee.onOffRefresh()
-}
-
-def refresh() {
-    refreshAttributes() + configureAttributes()
-}
-
-def poll() {
-    refreshAttributes()
-}
-
-def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    configureAttributes() + refreshAttributes()
-}
-
-def configureAttributes() {
-    zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
-}
-
-def refreshAttributes() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.readAttribute(0x0300, 0x00) + zigbee.readAttribute(0x0300, ATTRIBUTE_HUE) + zigbee.readAttribute(0x0300, ATTRIBUTE_SATURATION)
-}
-
-def setColorTemperature(value) {
-    zigbee.setColorTemperature(value) + ["delay 1500"] + zigbee.colorTemperatureRefresh()
-}
-
-def setLevel(value) {
-    zigbee.setLevel(value) + ["delay 1500"] + zigbee.levelRefresh()         //adding refresh because of ZLL bulb not conforming to send-me-a-report
-}
-
-def setColor(value){
-    log.trace "setColor($value)"
-    zigbee.on() + setHue(value.hue) + ["delay 300"] + setSaturation(value.saturation) + ["delay 2000"] + refreshAttributes()
-}
-
-def setHue(value) {
-    def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500")       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
-}
-
-def setSaturation(value) {
-    def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500")      //payload-> sat value, transition time
-}

devicetypes/smartthings/zll-white-color-temperature-bulb.src/zll-white-color-temperature-bulb.groovy

@@ -1,124 +0,0 @@
-/**
- *  Copyright 2016 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-
-metadata {
-    definition (name: "ZLL White Color Temperature Bulb", namespace: "smartthings", author: "SmartThings") {
-
-        capability "Actuator"
-        capability "Color Temperature"
-        capability "Configuration"
-        capability "Polling"
-        capability "Refresh"
-        capability "Switch"
-        capability "Switch Level"
-
-        attribute "colorName", "string"
-        command "setGenericName"
-
-        fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 1000, 0B04, FC0F", outClusters: "0019", "manufacturer":"OSRAM", "model":"Classic A60 TW", deviceJoinName: "OSRAM LIGHTIFY LED Classic A60 Tunable White"
-        fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 1000, FC0F", outClusters: "0019", "manufacturer":"OSRAM", "model":"PAR16 50 TW", deviceJoinName: "OSRAM LIGHTIFY LED PAR16 50 Tunable White"
-    }
-
-    // UI tile definitions
-    tiles(scale: 2) {
-        multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-            tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-                attributeState "on", label:'${name}', action:"switch.off", icon:"st.switches.light.on", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "off", label:'${name}', action:"switch.on", icon:"st.switches.light.off", backgroundColor:"#ffffff", nextState:"turningOn"
-                attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.switches.light.on", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.switches.light.off", backgroundColor:"#ffffff", nextState:"turningOn"
-            }
-            tileAttribute ("device.level", key: "SLIDER_CONTROL") {
-                attributeState "level", action:"switch level.setLevel"
-            }
-            tileAttribute ("colorName", key: "SECONDARY_CONTROL") {
-                attributeState "colorName", label:'${currentValue}'
-            }
-        }
-
-        standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-        }
-
-        controlTile("colorTempSliderControl", "device.colorTemperature", "slider", width: 4, height: 2, inactiveLabel: false, range:"(2700..6500)") {
-            state "colorTemperature", action:"color temperature.setColorTemperature"
-        }
-        valueTile("colorTemp", "device.colorTemperature", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "colorTemperature", label: '${currentValue} K'
-        }
-
-        main(["switch"])
-        details(["switch", "colorTempSliderControl", "colorTemp", "refresh"])
-    }
-}
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-    log.debug "description is $description"
-    def event = zigbee.getEvent(description)
-    if (event) {
-        sendEvent(event)
-    }
-    else {
-        log.warn "DID NOT PARSE MESSAGE for description : $description"
-        log.debug zigbee.parseDescriptionAsMap(description)
-    }
-}
-
-def off() {
-    zigbee.off() + ["delay 1500"] + zigbee.onOffRefresh()
-}
-
-def on() {
-    zigbee.on() + ["delay 1500"] + zigbee.onOffRefresh()
-}
-
-def setLevel(value) {
-    zigbee.setLevel(value) + ["delay 1500"] + zigbee.levelRefresh()
-}
-
-def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.colorTemperatureConfig()
-}
-
-def poll() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
-}
-
-def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
-}
-
-def setColorTemperature(value) {
-    setGenericName(value)
-    zigbee.setColorTemperature(value) + ["delay 1500"] + zigbee.colorTemperatureRefresh()
-}
-
-//Naming based on the wiki article here: http://en.wikipedia.org/wiki/Color_temperature
-def setGenericName(value){
-    if (value != null) {
-        def genericName = ""
-        if (value < 3300) {
-            genericName = "Soft White"
-        } else if (value < 4150) {
-            genericName = "Moonlight"
-        } else if (value <= 5000) {
-            genericName = "Cool White"
-        } else {
-            genericName = "Daylight"
-        }
-        sendEvent(name: "colorName", value: genericName)
-    }
-}

smartapps/smartthings/turn-it-on-for-1-minutes.src/turn-it-on-for-1-minutes.groovy

@@ -0,0 +1,56 @@
+/**
+ *  Copyright 2015 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ *  Turn It On For 5 Minutes
+ *  Turn on a switch when a contact sensor opens and then turn it back off 5 minutes later.
+ *
+ *  Author: SmartThings
+ */
+definition(
+    name: "Turn It On For 1 Minutes",
+    namespace: "smartthings",
+    author: "mr.kim",
+    description: "When a SmartSense Multi is opened, a switch will be turned on, and then turned off after 5 minutes.",
+    category: "Safety & Security",
+    iconUrl: "https://s3.amazonaws.com/smartapp-icons/Meta/light_contact-outlet.png",
+    iconX2Url: "https://s3.amazonaws.com/smartapp-icons/Meta/light_contact-outlet@2x.png"
+)
+
+preferences {
+	section("When it opens..."){
+		input "contact1", "capability.contactSensor"
+	}
+	section("Turn on a switch for 5 minutes..."){
+		input "switch1", "capability.switch"
+	}
+}
+
+def installed() {
+	log.debug "Installed with settings: ${settings}"
+	subscribe(contact1, "contact.open", contactOpenHandler)
+}
+
+def updated(settings) {
+	log.debug "Updated with settings: ${settings}"
+	unsubscribe()
+	subscribe(contact1, "contact.open", contactOpenHandler)
+}
+
+def contactOpenHandler(evt) {
+	switch1.on()
+	def fiveMinuteDelay = 60 * 1
+	runIn(fiveMinuteDelay, turnOffSwitch)
+}
+
+def turnOffSwitch() {
+	switch1.off()
+}