MSA-1554: Smartapps is available in association with SLEEPsense DTH.

I was doing this work wiht  Jenny.

e-mail : jihyouk.choi@samsung.com
name : jihyouk-Choi

devicetypes/smartthings/cree-bulb.src/cree-bulb.groovy

@@ -59,15 +59,6 @@ metadata {
     }
 }
 
-def installed() {
-    log.debug "${device} installed"
-}
-
-def updated() {
-    log.debug "${device} updated"
-    configureHealthCheck()
-}
-
 // Parse incoming device messages to generate events
 def parse(String description) {
     log.debug "description is $description"
@@ -105,14 +96,6 @@ def refresh() {
     zigbee.onOffRefresh() + zigbee.levelRefresh()
 }
 
-def configureHealthCheck() {
-    log.debug "configureHealthCheck"
-    unschedule("healthPoll")
-    runEvery5Minutes("healthPoll")
-    // Device-Watch allows 2 check-in misses from device
-    sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
-
 def healthPoll() {
     log.debug "healthPoll()"
     def cmds = zigbee.onOffRefresh() + zigbee.levelRefresh()
@@ -120,5 +103,9 @@ def healthPoll() {
 }
 
 def configure() {
-    refresh()
+    unschedule()
+    runEvery5Minutes("healthPoll")
+    // Device-Watch allows 2 check-in misses from device
+    sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    zigbee.onOffRefresh() + zigbee.levelRefresh()
 }

devicetypes/smartthings/smartpower-outlet.src/smartpower-outlet.groovy

@@ -74,15 +74,6 @@ metadata {
 	}
 }
 
-def installed() {
-	log.debug "${device} installed"
-}
-
-def updated() {
-	log.debug "${device} updated"
-	configureHealthCheck()
-}
-
 // Parse incoming device messages to generate events
 def parse(String description) {
 	log.debug "description is $description"
@@ -149,14 +140,10 @@ def refresh() {
 	zigbee.onOffRefresh() + zigbee.electricMeasurementPowerRefresh()
 }
 
-def configureHealthCheck() {
+def configure() {
 	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
 	sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
-
-def configure() {
-
 
 	// OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
 	refresh() + zigbee.onOffConfig(0, 300) + powerConfig()

devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy

@@ -84,15 +84,6 @@ metadata {
 	}
 }
 
-def installed() {
-	log.debug "${device} installed"
-}
-
-def updated() {
-	log.debug "${device} updated"
-	configureHealthCheck()
-}
-
 def parse(String description) {
 	log.debug "description: $description"
 
@@ -312,13 +303,11 @@ def refresh() {
 	return refreshCmds + enrollResponse()
 }
 
-def configureHealthCheck() {
+def configure() {
 	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
 	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
 
-def configure() {
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
 	return refresh() + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) // send refresh cmds as part of config

devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy

@@ -88,15 +88,6 @@ metadata {
 	}
 }
 
-def installed() {
-	log.debug "${device} installed"
-}
-
-def updated() {
-	log.debug "${device} updated"
-	configureHealthCheck()
-}
-
 def parse(String description) {
 	log.debug "description: $description"
 
@@ -327,13 +318,11 @@ def refresh() {
 	return refreshCmds + enrollResponse()
 }
 
-def configureHealthCheck() {
+def configure() {
 	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
 	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
 
-def configure() {
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
 	return refresh() + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) // send refresh cmds as part of config

devicetypes/smartthings/smartsense-multi-sensor.src/smartsense-multi-sensor.groovy

@@ -115,34 +115,6 @@ metadata {
 	}
  }
 
-def installed() {
-	log.debug "${device} installed"
-}
-
-def updated() {
-	log.debug "updated called"
-	log.info "garage value : $garageSensor"
-	if (garageSensor == "Yes") {
-		def descriptionText = "Updating device to garage sensor"
-		if (device.latestValue("status") == "open") {
-			sendEvent(name: 'status', value: 'garage-open', descriptionText: descriptionText, translatable: true)
-		}
-		else if (device.latestValue("status") == "closed") {
-			sendEvent(name: 'status', value: 'garage-closed', descriptionText: descriptionText, translatable: true)
-		}
-	}
-	else {
-		def descriptionText = "Updating device to open/close sensor"
-		if (device.latestValue("status") == "garage-open") {
-			sendEvent(name: 'status', value: 'open', descriptionText: descriptionText, translatable: true)
-		}
-		else if (device.latestValue("status") == "garage-closed") {
-			sendEvent(name: 'status', value: 'closed', descriptionText: descriptionText, translatable: true)
-		}
-	}
-	configureHealthCheck()
-}
-
 def parse(String description) {
 	Map map = [:]
 	if (description?.startsWith('catchall:')) {
@@ -274,6 +246,29 @@ private Map parseIasMessage(String description) {
 	return resultMap
 }
 
+def updated() {
+	log.debug "updated called"
+	log.info "garage value : $garageSensor"
+	if (garageSensor == "Yes") {
+		def descriptionText = "Updating device to garage sensor"
+		if (device.latestValue("status") == "open") {
+			sendEvent(name: 'status', value: 'garage-open', descriptionText: descriptionText, translatable: true)
+		}
+		else if (device.latestValue("status") == "closed") {
+			sendEvent(name: 'status', value: 'garage-closed', descriptionText: descriptionText, translatable: true)
+		}
+	}
+	else {
+		def descriptionText = "Updating device to open/close sensor"
+		if (device.latestValue("status") == "garage-open") {
+			sendEvent(name: 'status', value: 'open', descriptionText: descriptionText, translatable: true)
+		}
+		else if (device.latestValue("status") == "garage-closed") {
+			sendEvent(name: 'status', value: 'closed', descriptionText: descriptionText, translatable: true)
+		}
+	}
+}
+
 def getTemperature(value) {
 	def celsius = Integer.parseInt(value, 16).shortValue() / 100
 	if(getTemperatureScale() == "C"){
@@ -416,13 +411,11 @@ def refresh() {
 	return refreshCmds + enrollResponse()
 }
 
-def configureHealthCheck(){
+def configure() {
 	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
 	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
 
-def configure() {
 	log.debug "Configuring Reporting"
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity

devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy

@@ -75,15 +75,6 @@ metadata {
 	}
 }
 
-def installed() {
-	log.debug "${device} installed"
-}
-
-def updated() {
-	log.debug "${device} updated"
-	configureHealthCheck()
-}
-
 def parse(String description) {
 	log.debug "description: $description"
 
@@ -274,12 +265,11 @@ def refresh() {
 	return refreshCmds + enrollResponse()
 }
 
-def configureHealthCheck() {
+def configure() {
 	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
 	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
-def configure() {
+
 	log.debug "Configuring Reporting, IAS CIE, and Bindings."
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy

@@ -69,15 +69,6 @@ metadata {
 	}
 }
 
-def installed() {
-	log.debug "${device} installed"
-}
-
-def updated() {
-	log.debug "${device} updated"
-	configureHealthCheck()
-}
-
 def parse(String description) {
 	log.debug "description: $description"
 
@@ -277,13 +268,11 @@ def refresh()
 			zigbee.readAttribute(0x0001, 0x0020)
 }
 
-def configureHealthCheck() {
+def configure() {
 	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
 	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
 
-def configure() {
 	log.debug "Configuring Reporting and Bindings."
 	def humidityConfigCmds = [
 		"zdo bind 0x${device.deviceNetworkId} 1 1 0xFC45 {${device.zigbeeId}} {}", "delay 500",

devicetypes/smartthings/zigbee-dimmer-power.src/.st-ignore

@@ -1,2 +0,0 @@
-.st-ignore
-README.md

devicetypes/smartthings/zigbee-dimmer-power.src/README.md

@@ -1,41 +0,0 @@
-# GE Plug-In/In-Wall Smart Dimmer (ZigBee)
-
-
-
-Works with:
-
-* [GE In-Wall Smart Dimmer (ZigBee)](https://shop.smartthings.com/#!/products/ge-in-wall-smart-dimmer-switch)
-* [GE Plug-In Smart Dimmer (ZigBee)](https://www.smartthings.com/works-with-smartthings/ge/ge-plug-in-smart-dimmer-zigbee)
-
-## Table of contents
-
-* [Capabilities](#capabilities)
-* [Health](#device-health)
-* [Troubleshooting](#Troubleshooting)
-
-## Capabilities
-
-* **Actuator** - represents that a Device has commands
-* **Configuration** - _configure()_ command called when device is installed or device preferences updated
-* **Refresh** - _refresh()_ command for status updates
-* **Power Meter** - ability to check the power meter(energy consumption) of device
-* **Sensor** - represents the device sensor capability
-* **Switch** - can detect state (possible values: on/off)
-* **Switch Level** - represents current light level, usually 0-100 in percent
-* **Health Check** - indicates ability to get device health notifications
-
-## Device Health
-
-A Zigbee dimmer with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime.
-This gives the device twice the amount of time to respond before it is marked as offline.
-Enrolls with default periodic reporting until newer 5 min interval is confirmed
-It then enrolls the device with updated checkInterval i.e. 12 mins
-
-## Troubleshooting
-
-If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
-Pairing needs to be tried again by placing the device closer to the hub.
-Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
-* [GE Z-Wave In-Wall Smart Dimmer (GE 45857) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/204988564-GE-In-Wall-Smart-Dimmer-45857GE-ZigBee-)
-* [GE Zigbee Plug-in Smart Dimmer (GE 45852) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/205239280-GE-Plug-In-Smart-Dimmer-45852GE-ZigBee-)

devicetypes/smartthings/zigbee-dimmer-power.src/zigbee-dimmer-power.groovy

@@ -21,7 +21,6 @@ metadata {
         capability "Sensor"
         capability "Switch"
         capability "Switch Level"
-        capability "Health Check"
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B04"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702"
@@ -71,20 +70,8 @@ def parse(String description) {
         }
     }
     else {
-        def cluster = zigbee.parse(description)
-        if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
-            if (cluster.data[0] == 0x00){
-                log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
-                sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-            }
-            else {
-                log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
-            }
-        }
-        else {
-            log.warn "DID NOT PARSE MESSAGE for description : $description"
-            log.debug zigbee.parseDescriptionAsMap(description)
-        }
+        log.warn "DID NOT PARSE MESSAGE for description : $description"
+        log.debug zigbee.parseDescriptionAsMap(description)
     }
 }
 
@@ -100,22 +87,11 @@ def setLevel(value) {
     zigbee.setLevel(value)
 }
 
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-    return zigbee.onOffRefresh()
-}
-
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
 }
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-
-    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
-    // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
     refresh()
 }

devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy

@@ -48,15 +48,6 @@ metadata {
     }
 }
 
-def installed() {
-    log.debug "${device} installed"
-}
-
-def updated() {
-    log.debug "${device} updated"
-    configureHealthCheck()
-}
-
 // Parse incoming device messages to generate events
 def parse(String description) {
     log.debug "description is $description"
@@ -109,13 +100,12 @@ def refresh() {
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig()
 }
 
-def configureHealthCheck() {
+def configure() {
+    log.debug "Configuring Reporting and Bindings."
     // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
     sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
 
-def configure() {
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig()
 }

devicetypes/smartthings/zigbee-rgbw-bulb.src/zigbee-rgbw-bulb.groovy

@@ -70,16 +70,6 @@ metadata {
     }
 }
 
-
-def installed() {
-    log.debug "${device} installed"
-}
-
-def updated() {
-    log.debug "${device} updated"
-    configureHealthCheck()
-}
-
 //Globals
 private getATTRIBUTE_HUE() { 0x0000 }
 private getATTRIBUTE_SATURATION() { 0x0001 }
@@ -148,17 +138,16 @@ def ping() {
 }
 
 def refresh() {
-    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_COLOR_TEMPERATURE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION) + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
 }
 
-def configureHealthCheck() {
+def configure() {
+    log.debug "Configuring Reporting and Bindings."
     // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
     sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
 
-def configure() {
+    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     refresh()
 }
 

devicetypes/smartthings/zigbee-switch-power.src/zigbee-switch-power.groovy

@@ -20,7 +20,6 @@ metadata {
         capability "Power Meter"
         capability "Sensor"
         capability "Switch"
-        capability "Health Check"
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0B04"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0702"
@@ -78,26 +77,10 @@ def on() {
 }
 
 def refresh() {
-    Integer reportIntervalMinutes = 5
-    zigbee.onOffRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig(0,reportIntervalMinutes * 60) + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
+    zigbee.onOffRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
 }
 
 def configure() {
-    log.debug "in configure()"
-    configureHealthCheck()
-}
-
-def configureHealthCheck() {
-    Integer hcIntervalMinutes = 12
+    log.debug "Configuring Reporting and Bindings."
     refresh()
-    sendEvent(name: "checkInterval", value: hcIntervalMinutes * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
-
-def updated() {
-    log.debug "in updated()"
-    configureHealthCheck()
-}
-
-def ping() {
-    return zigbee.onOffRefresh()
 }

devicetypes/smartthings/zigbee-switch.src/zigbee-switch.groovy

@@ -21,7 +21,6 @@ metadata {
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0006", outClusters: "0003, 0006, 0019, 0406", manufacturer: "Leviton", model: "ZSS-10", deviceJoinName: "Leviton Switch"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0006", outClusters: "000A", manufacturer: "HAI", model: "65A21-1", deviceJoinName: "Leviton Wireless Load Control Module-30amp"
     }
 
     // simulator metadata

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/zigbee-white-color-temperature-bulb.groovy

@@ -69,15 +69,6 @@ metadata {
     }
 }
 
-def installed() {
-    log.debug "${device} installed"
-}
-
-def updated() {
-    log.debug "${device} updated"
-    configureHealthCheck()
-}
-
 // Parse incoming device messages to generate events
 def parse(String description) {
     log.debug "description is $description"
@@ -130,17 +121,16 @@ def ping() {
 }
 
 def refresh() {
-    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig()
 }
 
-def configureHealthCheck() {
+def configure() {
+    log.debug "Configuring Reporting and Bindings."
     // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
     sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-}
 
-def configure() {
+    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     refresh()
 }
 

smartapps/smartsolutionsv2/sleeping/sleep-routine.src/sleep-routine.groovy

@@ -0,0 +1,113 @@
+/**
+ *  Sleep Wizard
+ *
+ *  Copyright 2015 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+definition(
+    name: "Sleep Routine",
+    namespace: "smartsolutionsv2/sleeping",
+    author: "SmartThings",
+    description: "Create rules to control devices based on a sleep sensor, including in bed, out of bed, sleeping, and not sleeping.",
+    category: "My Apps",
+    iconUrl: "https://s3.amazonaws.com/smartthings-plus/category-icons/sleepsense.png",
+    iconX2Url: "https://s3.amazonaws.com/smartthings-plus/category-icons/sleepsense.png",
+    iconX3Url: "https://s3.amazonaws.com/smartthings-plus/category-icons/sleepsense.png",
+    singleInstance: true
+)
+
+preferences {
+	page(name: "main", title: getLabel("str_Title"), install: true, uninstall: true) {
+    	section {
+        	app(name: "smartsleepautomation", appName: "Smart Sleep Automation", namespace: "smartsolutionsv2/sleeping", title: getLabel("str_SectionTitle"), multiple: true, uninstall: true)
+        }
+    }
+}
+
+
+def installed() {
+	log.debug "Installed with settings: ${settings}"
+	initialize()
+}
+
+def updated() {
+	log.debug "Updated with settings: ${settings}"
+	initialize()
+}
+
+def initialize() {
+    
+    updateSolutionSummary();
+}
+
+def updateSolutionSummary() {
+	def numChildApps = getChildApps().size();
+    def text = "${numChildApps} rules configured";
+    sendEvent(
+    	linkText: numChildApps.toString(),
+        descriptionText: next,
+        eventType: "SOLUTION_SUMMARY",
+        name: "summary",
+        value: numChildApps,
+        data: [["icon": "indicator-dot-gray", "iconColor": "#878787", "value":text]],
+        displayed: false
+    );
+}
+
+
+card("Action History") { 
+     tiles { 
+         eventTile { }
+ 
+     } 
+ } 
+
+
+
+def getLabel(value)
+{
+    def str_Title=[
+            "kr": "룰",
+            "us": "Rules"
+    ]
+
+    def str_SectionTitle=[
+            "kr": "새로운 자동화 룰 만들기",
+            "us": "New Sleep Routine Automation"
+    ]
+
+    
+    def lang = "us"
+
+    if(lang == "ko") //clientLocale?.language
+    {
+        switch(value)
+        {
+            case "str_Title":
+                return str_Title["kr"]
+            case "str_SectionTitle":
+                return str_SectionTitle["kr"]
+        }
+    }
+    else
+    {
+        switch(value)
+        {
+            case "str_Title":
+                return str_Title["us"]
+            case "str_SectionTitle":
+                return str_SectionTitle["us"]
+        }
+    }
+    return "Unknown"
+}
+