MSA-1660: The Qubino Weatherstation device is a RF 433MHz to Z-Wave bridge device, that translates the data reported by RF sensors into a Z-Wave Multichannel device.

It provides two channel temperature and humidity measurements (reported by separate sensors) along with the rain rate, wind gust, wind velocity, wind direction and temperature measurement.

The device handler is compatible with most available automation SmartApps that do not allow for non-capability attributes to be used (the channel 1 temperature and humidity are mirrored for these), whereas with SmartApps that allow custom attributes to be used as condition triggers it is fully compatible.

The device handler takes care of setting up a multichannel lifeline association in order to receive pushed multichannel encapsulated reports from the device's endpoints, allowing for less network congestion as would be present in a polling approach.

devicetypes/goap/qubino-weatherstation.src/qubino-weatherstation.groovy

@@ -0,0 +1,486 @@
+/**
+ *  Qubino Weatherstation
+ *	Device Handler 
+ *	Version 1.0
+ *  Date: 16.12.2016
+ *	Author: Kristjan Jamšek (Kjamsek), Goap d.o.o.
+ *  Copyright 2016 Kristjan Jamšek
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ * - DEVICE HANDLER FOR QUBINO WEATHERSTATION Z-WAVE DEVICE -  
+ *	The handler supports all unsecure functions of the Qubino Weatherstation device. Configuration parameters and
+ *	association groups can be set in the device's preferences screen, but they are applied on the device only after
+ *	pressing the 'Set configuration' and 'Set associations' buttons on the bottom of the details view. 
+ *
+ *	This device handler supports data values that are currently not implemented as capabilities, so custom attribute 
+ *	states are used. Please use a SmartApp that supports custom attribute monitoring with this device in your rules.
+ *	By default the 'Temperature Measurement' and 'Relative Humidity Measurement' capability states are mirrored from
+ *	the custom attribute state values 'temperatureCh1' and 'humidityCh1'.
+ *
+ *	This device handler uses hubAction in configure() method in order to set a MultiChannel Lifeline association to the
+ *	device, so reports from all endpoints can be received. 
+ *
+ *
+ *	CHANGELOG:
+ *	0.99: Final release code cleanup and commenting
+ *	1.00: Added comments to code for readability
+ */
+metadata {
+	definition (name: "Qubino Weatherstation", namespace: "Goap", author: "Kristjan Jamšek") {
+		capability "Configuration" //Needed for configure() function to set MultiChannel Lifeline Association Set
+		capability "Temperature Measurement" //Used on main tile, needed in order to have the device appear in capabilities lists, mirrors temperatureCh1 attribute states
+		capability "Relative Humidity Measurement" //Needed in order to have the device appear in capabilities lists, mirrors humidityCh1 attribute states
+		capability "Sensor" // - Tagging capability
+		
+		attribute "temperatureCh1", "number" // temperature attribute for Ch1 Temperature reported by device's endpoint 1
+		attribute "windDirection", "number" // wind direction attribute for Wind Gauge - Direction reported by device's endpoint 2
+		attribute "windVelocity", "number" // wind velocity attribute for Wind Gauge - Velocity reported by device's endpoint 3
+		attribute "windGust", "number" // wind gust velocity attribute for Wind Gauge - Wind gust reported by device's endpoint 4
+		attribute "windTemperature", "number" // wind temperature attribute for Wind Gauge - Temperature reported by device's endpoint 5
+		attribute "windChillTemperature", "number" // wind chill temperature attribute for Wind Gauge - Wind Chill reported by device's endpoint 6
+		attribute "rainRate", "number" // rain rate attribute for Rain Sensor data reported by device's endpoint 7
+		attribute "humidityCh1", "number" // humidity attribute for Ch1 Humidity reported by device's endpoint 8
+		attribute "temperatureCh2", "number" // temperature attribute for Ch2 Temperature reported by device's endpoint 9
+		attribute "humidityCh2", "number" // humidity attribute for Ch2 Humidity reported by device's endpoint 10
+		
+		attribute "setConfigParams", "string" // attribute for tile element for setConfigurationParams command
+		attribute "setAssocGroups", "string" // attribute for tile element for setAssociations command
+		
+		command "setConfigurationParams" // command to issue Configuration Set command sequence according to user's preferences
+		command "setAssociations" // command to issue Association Set command sequence according to user's preferences
+
+        fingerprint mfr:"0159", prod:"0007", model:"0053"  //Manufacturer Information values for Qubino Weatherstation
+	}
+
+
+	simulator {
+		// TESTED WITH PHYSICAL DEVICE - UNNEEDED
+	}
+
+	tiles(scale: 2) {
+		valueTile("temperature", "device.temperature") {
+			state("temperature", label:'${currentValue} °', unit:"°", icon: "st.Weather.weather2", backgroundColors: [
+				// Celsius Color Range
+				[value: 0, color: "#153591"],
+				[value: 7, color: "#1e9cbb"],
+				[value: 15, color: "#90d2a7"],
+				[value: 23, color: "#44b621"],
+				[value: 29, color: "#f1d801"],
+				[value: 33, color: "#d04e00"],
+				[value: 36, color: "#bc2323"],
+				// Fahrenheit Color Range
+				[value: 40, color: "#153591"],
+				[value: 44, color: "#1e9cbb"],
+				[value: 59, color: "#90d2a7"],
+				[value: 74, color: "#44b621"],
+				[value: 84, color: "#f1d801"],
+				[value: 92, color: "#d04e00"],
+				[value: 96, color: "#bc2323"]
+			])
+		}		
+		valueTile("humidity", "device.humidity") {
+			state("humidity", label:'${currentValue} %', unit:"%", display:false)
+		}		
+		standardTile("temperatureCh1", "device.temperatureCh1", width: 3, height: 3) {
+			state("temperatureCh1", label:'Temperature Ch1: ${currentValue} °', unit:'°', icon: 'st.Weather.weather2')
+		}
+		standardTile("windDirection", "device.windDirection", width: 3, height: 3) {
+			state("windDirection", label:'Wind Direction: ${currentValue} °', unit: "°", icon: 'st.Outdoor.outdoor20')
+		}
+		standardTile("windVelocity", "device.windVelocity", width: 3, height: 3) {
+			state("windVelocity", label:'Wind Velocity: ${currentValue} m/s', unit:"m/s", icon: 'st.Weather.weather1')
+		}
+		standardTile("windGust", "device.windGust", width: 3, height: 3) {
+			state("windGust", label:'Wind Gust: ${currentValue} m/s', unit:"m/s", icon: 'st.Weather.weather1')
+		}
+		standardTile("windTemperature", "device.windTemperature", width: 3, height: 3) {
+			state("windTemperature", label:'Wind Temperature: ${currentValue} °', unit:'°', icon: 'st.Weather.weather2')
+		}
+		standardTile("windChillTemperature", "device.windChillTemperature", width: 3, height: 3) {
+			state("windChillTemperature", label:'Wind Chill: ${currentValue} °', unit:'°', icon: 'st.Weather.weather2')
+		}
+		standardTile("rainRate", "device.rainRate", width: 3, height: 3) {
+			state("rainRate", label:'Rain Sensor: ${currentValue} mm/h', unit:"mm/h", icon: 'st.Weather.weather10')
+		}
+		standardTile("humidityCh1", "device.humidityCh1", width: 3, height: 3) {
+			state("humidityCh1", label:'Humidity Ch1: ${currentValue} %', unit:"%", icon: 'st.Weather.weather12')
+		}
+		standardTile("temperatureCh2", "device.temperatureCh2", width: 3, height: 3) {
+			state("temperatureCh2", label:'Temperature Ch2: ${currentValue} °', unit:'°', icon: 'st.Weather.weather2')
+		}
+		standardTile("humidityCh2", "device.humidityCh2", width: 3, height: 3) {
+			state("humidityCh2", label:'Humidity Ch2: ${currentValue} %', unit:"%", icon: 'st.Weather.weather12')
+		}
+		standardTile("setConfigParams", "device.setConfigParams", decoration: "flat", width: 3, height: 3) {
+			state("setConfigParams", label:'Set configuration', action:'setConfigurationParams', icon: "st.secondary.tools")
+		}
+		standardTile("setAssocGroups", "device.setAssocGroups", decoration: "flat", width: 3, height: 3) {
+			state("setAssocGroups", label:'Set associations', action:'setAssociations', icon: "st.secondary.tools")
+		}
+		
+		main("temperature")
+		details(["temperatureCh1", "humidityCh1", "windDirection", "windVelocity", "windGust", "windTemperature", "windChillTemperature", "rainRate", "temperatureCh2", "humidityCh2", "setConfigParams", "setAssocGroups"])
+
+	}
+	preferences {
+/**
+*			--------	CONFIGURATION PARAMETER SECTION	--------
+*/
+				input name: "param1", type: "number", range: "0..8800", required: false,
+					title: "1. Wind Gauge, Wind Gust Top Value. " +
+						   "If the Wind Gust is higher than the parameter value, the device triggers an association.\n" +
+						   "Available settings:\n" +
+						   "0 ... 8800 = value from 0,00 m/s to 88,00 m/s,\n" +
+						   "Default value: 1000 (10,00 m/s)."
+				input name: "param2", type: "number", range: "0..30000", required: false,
+					title: "2. Rain Gauge, Rain Rate Top Value. " +
+						   "If the Rain Sensor Rain Rate is higher than the parameter value, the device triggers an association.\n" +
+						   "Available settings:\n" +
+						   "0 ... 30000 = value from 0,00 mm/h to 300,00 mm/h,\n" +
+						   "Default value: 200 (2,00 mm/h)."          
+				input name: "param3", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "3. Wind Gauge, Wind Gust. " +
+						   "Available settings:\n" +
+						   "0 = If the Wind Gust is higher than the parameter number 1 value, then the device sends a Basic Set 0x00,\n" +
+						   "1 = If the Wind Gust is higher than the parameter number 1 value, then the device sends a Basic Set 0xFF,\n" +
+						   "Default value: 1."
+				input name: "param4", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "4. Rain Gauge, Rain Rate. " +
+						   "Available settings:\n" +
+						   "0 = If the Rain Rate is higher than the parameter number 2 value, then the device sends a Basic Set 0x00,\n" +
+						   "1 = If the Rain Rate is higher than the parameter number 2 value, then the device sends a Basic Set 0xFF,\n" +
+						   "Default value: 1."	
+				input name: "param5", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "5. Endpoint 1 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param6", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "6. Endpoint 2 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param7", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "7. Endpoint 3 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param8", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "8. Endpoint 4 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param9", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "9. Endpoint 5 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param10", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "10. Endpoint 6 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param11", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "11. Endpoint 7 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param12", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "12. Endpoint 8 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param13", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "13. Endpoint 9 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param14", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "14. Endpoint 10 - Unsolicited Report enable/disable. " +
+						   "Available settings:\n" +
+						   "0 = Unsolicited Report disabled,\n" +
+						   "1 = Unsolicited Report enabled,\n" +
+						   "Default value: 1."
+				input name: "param15", type: "enum", required: false,
+					options: ["0" : "0",
+							  "1" : "1"],
+					title: "15. Random ID enable/disable " +
+						   "Available settings:\n" +
+						   "0 = Random ID disabled,\n" +
+						   "1 = Random ID enabled,\n" +
+						   "Default value: 0."
+/**
+*			--------	ASSOCIATION GROUP SECTION	--------
+*/
+				input name: "assocGroup2", type: "text", required: false,
+					title: "Association group 2: \n" +
+						   "Basic On/Off command will be sent to associated nodes when the Wind Gust of the Wind Gauge exceeds the Configuration parameter 1 value. \n" +
+						   "NOTE: Insert the node Id value of the devices you wish to associate this group with. Multiple nodeIds can also be set at once by separating individual values by a comma (2,3,...)."
+						   
+				input name: "assocGroup3", type: "text", required: false,
+					title: "Association group 3: \n" +
+						   "Basic On/Off command will be sent to associated nodes when the Rain Rate exceeds the Configuration parameter 2 value. \n" +
+						   "NOTE: Insert the node Id value of the devices you wish to associate this group with. Multiple nodeIds can also be set at once by separating individual values by a comma (2,3,...)."
+	}
+}
+/**
+*	--------	HELPER METHODS SECTION	--------
+*/
+/**
+ * Converts a list of String type node id values to Integer type.
+ *
+ * @param stringList - a list of String type node id values.
+ * @return stringList - a list of Integer type node id values.
+*/
+def convertStringListToIntegerList(stringList){
+	for(int i=0;i<stringList.size();i++){
+		stringList[i] = stringList[i].toInteger()
+	}
+	return stringList
+}
+/**
+ * Converts temperature values to fahrenheit or celsius scales accordign to user's setting.
+ *
+ * @param scaleParam user set scale parameter.
+ * @param encapCmd received temperature parsed value.
+ * @return String type value of the converted temperature value.
+*/
+def convertDegrees(scaleParam, encapCmd){
+	switch (scaleParam) {
+		default:
+				break;
+		case "F":
+				if(encapCmd.scale == 1){
+					return encapCmd.scaledSensorValue.toString()
+				}else{
+					return (encapCmd.scaledSensorValue * 9 / 5 + 32).toString()
+				}
+				break;
+		case "C":
+				if(encapCmd.scale == 0){
+					return encapCmd.scaledSensorValue.toString()
+				}else{
+					return (encapCmd.scaledSensorValue * 9 / 5 + 32).toString()
+				}
+				break;
+	}
+}
+/*
+*	--------	HANDLE COMMANDS SECTION	--------
+*/
+/**
+ * Configuration capability command handler that executes after module inclusion to remove existing singlechannel association Lifeline and replace it
+ * with a multichannel Lifeline association setting for node id 1 and endpoint 1, which enables modules to report multichannel encapsulated frames.
+ *
+ * @param void
+ * @return List of commands that will be executed in sequence with 500 ms delay inbetween.
+*/
+def configure() {
+	log.debug "Qubino Weatherstation: configure()"
+	/** In this method we first clear the association group 1 that is set by SmartThings automatically.
+	* Afterwards we use physicalgraph.device.HubAction("8E0101000101") as a workaround for SmartThings' MultiChannel Association Command Class implementation,
+	* where we cannot set a node id and endpoint id. The hardcoded parameter "8E0101000101" should be interpreted in sequence as hexadecimal byte values:
+	* 8E010100 - Command class and command values, along with the field for singlechannel node id omitted
+	* 0101 - These two byte values represent the multichannel node id 01 followed by the endpoint id 01 (in general this value can be left as is unless 
+	*		 multiple subordinated controllers are included in your network. In that case please adjust these two value to the correct id.
+	*/
+	def assocCmds = []
+	assocCmds << zwave.associationV1.associationRemove(groupingIdentifier:1, nodeId:zwaveHubNodeId).format()
+	assocCmds << new physicalgraph.device.HubAction("8E0101000101")
+	return delayBetween(assocCmds, 500)
+}
+/**
+ * setAssociations command handler that sets user selected association groups. In case no node id is insetred the group is instead cleared.
+ * Lifeline association hidden from user influence by design.
+ *
+ * @param void
+ * @return List of Association commands that will be executed in sequence with 500 ms delay inbetween.
+*/
+def setAssociations() {
+	log.debug "Qubino Weatherstation: setAssociations()"
+	def assocSet = []
+	if(settings.assocGroup2 != null){
+		def group2parsed = settings.assocGroup2.tokenize(",")
+		group2parsed = convertStringListToIntegerList(group2parsed)
+		assocSet << zwave.associationV1.associationSet(groupingIdentifier:2, nodeId:group2parsed).format()
+	}else{
+		assocSet << zwave.associationV1.associationRemove(groupingIdentifier:2, nodeId: 0).format()
+	}
+	if(settings.assocGroup3 != null){
+		def group3parsed = settings.assocGroup3.tokenize(",")
+		group3parsed = convertStringListToIntegerList(group3parsed)
+		assocSet << zwave.associationV1.associationSet(groupingIdentifier:3, nodeId:group3parsed).format()
+	}else{
+		assocSet << zwave.associationV1.associationRemove(groupingIdentifier:3, nodeId: 0).format()
+	}
+	return delayBetween(assocSet, 500)
+	
+}
+/**
+ * setConfigurationParams command handler that sets user selected configuration parameters on the device. 
+ * In case no value is set for a specific parameter the method skips setting that parameter.
+ * Secure mdoe setting hidden from user influence by design.
+ *
+ * @param void
+ * @return List of Configuration Set commands that will be executed in sequence with 500 ms delay inbetween.
+*/
+def setConfigurationParams() {
+	log.debug "Qubino Weatherstation: setConfigurationParams()"
+	def configSequence = []
+	if(settings.param1 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 1, size: 2, scaledConfigurationValue: settings.param1.toInteger()).format()
+	}
+	if(settings.param2 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 2, size: 2, scaledConfigurationValue: settings.param2.toInteger()).format()
+	}
+	if(settings.param3 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 3, size: 1, scaledConfigurationValue: settings.param3.toInteger()).format()
+	}
+	if(settings.param4 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 4, size: 1, scaledConfigurationValue: settings.param4.toInteger()).format()
+	}
+	if(settings.param5 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 5, size: 1, scaledConfigurationValue: settings.param5.toInteger()).format()
+	}
+	if(settings.param6 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 6, size: 1, scaledConfigurationValue: settings.param6.toInteger()).format()
+	}
+	if(settings.param7 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 7, size: 1, scaledConfigurationValue: settings.param7.toInteger()).format()
+	}
+	if(settings.param8 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 8, size: 1, scaledConfigurationValue: settings.param8.toInteger()).format()
+	}
+	if(settings.param9 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 9, size: 1, scaledConfigurationValue: settings.param9.toInteger()).format()
+	}
+	if(settings.param10 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 10, size: 1, scaledConfigurationValue: settings.param10.toInteger()).format()
+	}
+	if(settings.param11 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 11, size: 1, scaledConfigurationValue: settings.param11.toInteger()).format()
+	}
+	if(settings.param12 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 12, size: 1, scaledConfigurationValue: settings.param12.toInteger()).format()
+	}
+	if(settings.param13 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 13, size: 1, scaledConfigurationValue: settings.param13.toInteger()).format()
+	}
+	if(settings.param14 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 14, size: 1, scaledConfigurationValue: settings.param14.toInteger()).format()
+	}
+	if(settings.param15 != null){
+		configSequence << zwave.configurationV1.configurationSet(parameterNumber: 15, size: 1, scaledConfigurationValue: settings.param15.toInteger()).format()
+	}	
+	return delayBetween(configSequence, 500)
+}
+/*
+*	--------	EVENT PARSER SECTION	--------
+*/
+/**
+ * parse function takes care of parsing received bytes and passing them on to event methods.
+ *
+ * @param description String type value of the received bytes.
+ * @return Parsed result of the received bytes.
+*/
+def parse(String description) {
+	log.debug "Qubino Weatherstation: Parsing '${description}'"
+	def result = null
+    def cmd = zwave.parse(description)
+    if (cmd) {
+		result = zwaveEvent(cmd)
+        log.debug "Parsed ${cmd} to ${result.inspect()}"
+    } else {
+		log.debug "Non-parsed event: ${description}"
+    }
+    return result
+}
+/**
+ * Event method for MultiChannelCmdEncap encapsulation frames.
+ *
+ * @param cmd Type physicalgraph.zwave.commands.multichannelv3.MultiChannelCmdEncap received command.
+ * @return List of events that will update UI elements for data display.
+*/
+def zwaveEvent(physicalgraph.zwave.commands.multichannelv3.MultiChannelCmdEncap cmd) {
+	def encapsulatedCommand = cmd.encapsulatedCommand([0x30: 1, 0x31: 1])
+	def tempScale = location.temperatureScale
+	def resultEvents = []
+	switch (cmd.sourceEndPoint) {
+		default:
+				break;
+		case 1:
+				resultEvents << createEvent(name:"temperatureCh1", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Temperature Ch1: "+convertDegrees(tempScale,encapsulatedCommand)+"°"+location.temperatureScale)
+				resultEvents << createEvent(name:"temperature", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Temperature Ch1: "+convertDegrees(tempScale,encapsulatedCommand)+"°"+location.temperatureScale, displayed: false)
+				break;
+		case 2:
+				resultEvents << createEvent(name:"windDirection", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"°", descriptionText: "Wind Direction: "+encapsulatedCommand.scaledSensorValue.toString()+" °")
+				break;
+		case 3:
+				resultEvents << createEvent(name:"windVelocity", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"m/s", descriptionText: "Wind Velocity: "+encapsulatedCommand.scaledSensorValue.toString()+" m/s")
+				break;
+		case 4:
+				resultEvents << createEvent(name:"windGust", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"m/s", descriptionText: "Wind Gust: "+encapsulatedCommand.scaledSensorValue.toString()+" m/s")
+				break;
+		case 5:
+				resultEvents << createEvent(name:"windTemperature", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Wind Temperature: "+convertDegrees(tempScale,encapsulatedCommand)+" °"+location.temperatureScale)
+				break;
+		case 6:
+				resultEvents << createEvent(name:"windChillTemperature", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Wind Chill: "+convertDegrees(tempScale,encapsulatedCommand)+" °"+location.temperatureScale)
+				break;
+		case 7:
+				resultEvents << createEvent(name:"rainRate", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"mm/h", descriptionText: "Rain Sensor: "+encapsulatedCommand.scaledSensorValue.toString()+" mm/h")
+				break;
+		case 8:
+				resultEvents << createEvent(name:"humidity", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"%", descriptionText: "Humidity Ch1: "+encapsulatedCommand.scaledSensorValue.toString()+" %", displayed: false)
+				resultEvents << createEvent(name:"humidityCh1", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"%", descriptionText: "Humidity Ch1: "+encapsulatedCommand.scaledSensorValue.toString()+" %")
+				break;
+		case 9:
+				resultEvents << createEvent(name:"temperatureCh2", value: convertDegrees(tempScale,encapsulatedCommand), unit:"°"+location.temperatureScale, descriptionText: "Temperature Ch2: "+convertDegrees(tempScale,encapsulatedCommand)+" °"+location.temperatureScale)
+				break;
+		case 10:
+				resultEvents << createEvent(name:"humidityCh2", value: encapsulatedCommand.scaledSensorValue.toString(), unit:"%", descriptionText: "Humidity Ch2: "+encapsulatedCommand.scaledSensorValue.toString()+" %")
+				break;
+	}
+	return resultEvents
+}

devicetypes/smartthings/dimmer-switch.src/dimmer-switch.groovy

@@ -22,10 +22,9 @@ metadata {
 		capability "Sensor"
 		capability "Health Check"
 
-		fingerprint mfr:"0063", prod:"4457", deviceJoinName: "GE In-Wall Smart Dimmer "
+		fingerprint mfr:"0063", prod:"4457", deviceJoinName: "Z-Wave Wall Dimmer"
-		fingerprint mfr:"0063", prod:"4944", deviceJoinName: "GE In-Wall Smart Dimmer "
+		fingerprint mfr:"0063", prod:"4944", deviceJoinName: "Z-Wave Wall Dimmer"
-		fingerprint mfr:"0063", prod:"5044", deviceJoinName: "GE Plug-In Smart Dimmer "
+		fingerprint mfr:"0063", prod:"5044", deviceJoinName: "Z-Wave Plug-In Dimmer"
-		fingerprint mfr:"0063", prod:"4944", model:"3034", deviceJoinName: "GE In-Wall Smart Fan Control"
 	}
 
 	simulator {

devicetypes/smartthings/zwave-dimmer-switch-generic.src/zwave-dimmer-switch-generic.groovy

@@ -24,10 +24,6 @@ metadata {
 		fingerprint inClusters: "0x26", deviceJoinName: "Z-Wave Dimmer"
 		fingerprint mfr:"001D", prod:"1902", deviceJoinName: "Z-Wave Dimmer"
 		fingerprint mfr:"001D", prod:"1B03", model:"0334", deviceJoinName: "Leviton Universal Dimmer"
-		fingerprint mfr:"011A", prod:"0102", model:"0201", deviceJoinName: "Enerwave In-Wall Dimmer"
-		fingerprint mfr:"001D", prod:"1001", model:"0334", deviceJoinName: "Leviton 3-Speed Fan Controller"
-		fingerprint mfr:"001D", prod:"0602", model:"0334", deviceJoinName: "Leviton Magnetic Low Voltage Dimmer"
-		fingerprint mfr:"001D", prod:"0401", model:"0334", deviceJoinName: "Leviton 600W Incandescent Dimmer"
 	}
 
 	simulator {

devicetypes/smartthings/zwave-door-sensor-as-smoke-detector.src/zwave-door-sensor-as-smoke-detector.groovy

@@ -1,273 +0,0 @@
-/**
- *  Copyright 2015 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- *  Z-Wave Door/Window Sensor
- *
- *  Author: SmartThings
- *  Date: 2013-11-3
- */
-
-metadata {
-	definition (name: "Z-Wave Door Sensor as Smoke Detector", namespace: "smartthings", author: "SmartThings") {
-		capability "Contact Sensor"
-		capability "Sensor"
-		capability "Battery"
-		capability "Configuration"
-
-		fingerprint deviceId: "0x2001", inClusters: "0x30,0x80,0x84,0x85,0x86,0x72"
-		fingerprint deviceId: "0x07", inClusters: "0x30"
-		fingerprint deviceId: "0x0701", inClusters: "0x5E,0x98"
-		fingerprint deviceId: "0x0701", inClusters: "0x5E,0x86,0x72,0x98", outClusters: "0x5A,0x82"
-		fingerprint deviceId: "0x0701", inClusters: "0x5E,0x80,0x71,0x85,0x70,0x72,0x86,0x30,0x31,0x84,0x59,0x73,0x5A,0x8F,0x98,0x7A", outClusters:"0x20" // Philio multi+
-	}
-
-	// simulator metadata
-	simulator {
-		// status messages
-		status "fire":  "command: 2001, payload: FF"
-		status "safe": "command: 2001, payload: 00"
-		status "wake up": "command: 8407, payload: "
-	}
-
-	// UI tile definitions
-	tiles {
-		standardTile("contact", "device.contact", width: 2, height: 2) {
-			state "fire",label: '${name}',icon: "st.alarm.smoke.smoke",backgroundColor: "#ffa81e"
-			state "safe",label: '${name}',icon: "st.alarm.smoke.clear",backgroundColor: "#79b821"
-		}
-		valueTile("battery", "device.battery", inactiveLabel: false, decoration: "flat") {
-			state "battery", label:'${currentValue}% battery', unit:""
-		}
-
-		main "contact"
-		details(["contact", "battery"])
-	}
-}
-
-def parse(String description) {
-	def result = null
-	if (description.startsWith("Err 106")) {
-		if (state.sec) {
-			log.debug description
-		} else {
-			result = createEvent(
-				descriptionText: "This sensor failed to complete the network security key exchange. If you are unable to control it via SmartThings, you must remove it from your network and add it again.",
-				eventType: "ALERT",
-				name: "secureInclusion",
-				value: "failed",
-				isStateChange: true,
-			)
-		}
-	} else if (description != "updated") {
-		def cmd = zwave.parse(description, [0x20: 1, 0x25: 1, 0x30: 1, 0x31: 5, 0x80: 1, 0x84: 1, 0x71: 3, 0x9C: 1])
-		if (cmd) {
-			result = zwaveEvent(cmd)
-		}
-	}
-	log.debug "parsed '$description' to $result"
-	return result
-}
-
-def updated() {
-	def cmds = []
-	if (!state.MSR) {
-		cmds = [
-			command(zwave.manufacturerSpecificV2.manufacturerSpecificGet()),
-			"delay 1200",
-			zwave.wakeUpV1.wakeUpNoMoreInformation().format()
-		]
-	} else if (!state.lastbat) {
-		cmds = []
-	} else {
-		cmds = [zwave.wakeUpV1.wakeUpNoMoreInformation().format()]
-	}
-	response(cmds)
-}
-
-def configure() {
-	commands([
-		zwave.manufacturerSpecificV2.manufacturerSpecificGet(),
-		zwave.batteryV1.batteryGet()
-	], 6000)
-}
-
-def sensorValueEvent(value) {
-	if (value) {
-		createEvent(name: "contact", value: "fire", descriptionText: "$device.displayName fire detected")
-	} else {
-		createEvent(name: "contact", value: "safe", descriptionText: "$device.displayName is safe")
-	}
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.basicv1.BasicReport cmd)
-{
-	sensorValueEvent(cmd.value)
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.basicv1.BasicSet cmd)
-{
-	sensorValueEvent(cmd.value)
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.switchbinaryv1.SwitchBinaryReport cmd)
-{
-	sensorValueEvent(cmd.value)
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.sensorbinaryv1.SensorBinaryReport cmd)
-{
-	sensorValueEvent(cmd.sensorValue)
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.sensoralarmv1.SensorAlarmReport cmd)
-{
-	sensorValueEvent(cmd.sensorState)
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.notificationv3.NotificationReport cmd)
-{
-	def result = []
-	if (cmd.notificationType == 0x06 && cmd.event == 0x16) {
-		result << sensorValueEvent(1)
-	} else if (cmd.notificationType == 0x06 && cmd.event == 0x17) {
-		result << sensorValueEvent(0)
-	} else if (cmd.notificationType == 0x07) {
-		if (cmd.v1AlarmType == 0x07) {  // special case for nonstandard messages from Monoprice door/window sensors
-			result << sensorValueEvent(cmd.v1AlarmLevel)
-		} else if (cmd.event == 0x01 || cmd.event == 0x02) {
-			result << sensorValueEvent(1)
-		} else if (cmd.event == 0x03) {
-			result << createEvent(descriptionText: "$device.displayName covering was removed", isStateChange: true)
-			if(!state.MSR) result << response(command(zwave.manufacturerSpecificV2.manufacturerSpecificGet()))
-		} else if (cmd.event == 0x05 || cmd.event == 0x06) {
-			result << createEvent(descriptionText: "$device.displayName detected glass breakage", isStateChange: true)
-		} else if (cmd.event == 0x07) {
-			if(!state.MSR) result << response(command(zwave.manufacturerSpecificV2.manufacturerSpecificGet()))
-			result << createEvent(name: "motion", value: "active", descriptionText:"$device.displayName detected motion")
-		}
-	} else if (cmd.notificationType) {
-		def text = "Notification $cmd.notificationType: event ${([cmd.event] + cmd.eventParameter).join(", ")}"
-		result << createEvent(name: "notification$cmd.notificationType", value: "$cmd.event", descriptionText: text, displayed: false)
-	} else {
-		def value = cmd.v1AlarmLevel == 255 ? "active" : cmd.v1AlarmLevel ?: "inactive"
-		result << createEvent(name: "alarm $cmd.v1AlarmType", value: value, displayed: false)
-	}
-	result
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.wakeupv1.WakeUpNotification cmd)
-{
-	def event = createEvent(descriptionText: "${device.displayName} woke up", isStateChange: false)
-	def cmds = []
-	if (!state.MSR) {
-		cmds << command(zwave.manufacturerSpecificV2.manufacturerSpecificGet())
-		cmds << "delay 1200"
-	}
-	if (!state.lastbat || now() - state.lastbat > 53*60*60*1000) {
-		cmds << command(zwave.batteryV1.batteryGet())
-	} else {
-		cmds << zwave.wakeUpV1.wakeUpNoMoreInformation().format()
-	}
-	[event, response(cmds)]
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.batteryv1.BatteryReport cmd) {
-	def map = [ name: "battery", unit: "%" ]
-	if (cmd.batteryLevel == 0xFF) {
-		map.value = 1
-		map.descriptionText = "${device.displayName} has a low battery"
-		map.isStateChange = true
-	} else {
-		map.value = cmd.batteryLevel
-	}
-	state.lastbat = now()
-	[createEvent(map), response(zwave.wakeUpV1.wakeUpNoMoreInformation())]
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.manufacturerspecificv2.ManufacturerSpecificReport cmd) {
-	def result = []
-
-	def msr = String.format("%04X-%04X-%04X", cmd.manufacturerId, cmd.productTypeId, cmd.productId)
-	log.debug "msr: $msr"
-	updateDataValue("MSR", msr)
-
-	retypeBasedOnMSR()
-
-	result << createEvent(descriptionText: "$device.displayName MSR: $msr", isStateChange: false)
-
-	if (msr == "011A-0601-0901") {  // Enerwave motion doesn't always get the associationSet that the hub sends on join
-		result << response(zwave.associationV1.associationSet(groupingIdentifier:1, nodeId:zwaveHubNodeId))
-	} else if (!device.currentState("battery")) {
-		if (msr == "0086-0102-0059") {
-			result << response(zwave.securityV1.securityMessageEncapsulation().encapsulate(zwave.batteryV1.batteryGet()).format())
-		} else {
-			result << response(command(zwave.batteryV1.batteryGet()))
-		}
-	}
-
-	result
-}
-
-def zwaveEvent(physicalgraph.zwave.commands.securityv1.SecurityMessageEncapsulation cmd) {
-	def encapsulatedCommand = cmd.encapsulatedCommand([0x20: 1, 0x25: 1, 0x30: 1, 0x31: 5, 0x80: 1, 0x84: 1, 0x71: 3, 0x9C: 1])
-	// log.debug "encapsulated: $encapsulatedCommand"
-	if (encapsulatedCommand) {
-		state.sec = 1
-		zwaveEvent(encapsulatedCommand)
-	}
-}
-
-def zwaveEvent(physicalgraph.zwave.Command cmd) {
-	createEvent(descriptionText: "$device.displayName: $cmd", displayed: false)
-}
-
-private command(physicalgraph.zwave.Command cmd) {
-	if (state.sec == 1) {
-		zwave.securityV1.securityMessageEncapsulation().encapsulate(cmd).format()
-	} else {
-		cmd.format()
-	}
-}
-
-private commands(commands, delay=200) {
-	delayBetween(commands.collect{ command(it) }, delay)
-}
-
-def retypeBasedOnMSR() {
-	switch (state.MSR) {
-		case "0086-0002-002D":
-			log.debug "Changing device type to Z-Wave Water Sensor"
-			setDeviceType("Z-Wave Water Sensor")
-			break
-		case "011F-0001-0001":  // Schlage motion
-		case "014A-0001-0001":  // Ecolink motion
-		case "014A-0004-0001":  // Ecolink motion +
-		case "0060-0001-0002":  // Everspring SP814
-		case "0060-0001-0003":  // Everspring HSP02
-		case "011A-0601-0901":  // Enerwave ZWN-BPC
-			log.debug "Changing device type to Z-Wave Motion Sensor"
-			setDeviceType("Z-Wave Motion Sensor")
-			break
-		case "013C-0002-000D":  // Philio multi +
-			log.debug "Changing device type to 3-in-1 Multisensor Plus (SG)"
-			setDeviceType("3-in-1 Multisensor Plus (SG)")
-			break
-		case "0109-2001-0106":  // Vision door/window
-			log.debug "Changing device type to Z-Wave Plus Door/Window Sensor"
-			setDeviceType("Z-Wave Plus Door/Window Sensor")
-			break
-		case "0109-2002-0205": // Vision Motion
-			log.debug "Changing device type to Z-Wave Plus Motion/Temp Sensor"
-			setDeviceType("Z-Wave Plus Motion/Temp Sensor")
-			break
-	}
-}

devicetypes/smartthings/zwave-switch-generic.src/zwave-switch-generic.groovy

@@ -25,9 +25,6 @@ metadata {
 		fingerprint mfr:"0063", prod:"4F50", model:"3031", deviceJoinName: "GE Plug-in Outdoor Switch"
 		fingerprint mfr:"001D", prod:"1D04", model:"0334", deviceJoinName: "Leviton Outlet"
 		fingerprint mfr:"001D", prod:"1C02", model:"0334", deviceJoinName: "Leviton Switch"
-		fingerprint mfr:"001D", prod:"0301", model:"0334", deviceJoinName: "Leviton 15A Switch"
-		fingerprint mfr:"011A", prod:"0101", model:"0102", deviceJoinName: "Enerwave On/Off Switch"
-		fingerprint mfr:"011A", prod:"0101", model:"0603", deviceJoinName: "Enerwave Duplex Receptacle"
 	}
 
 	// simulator metadata