MSA-2006: tet

devicetypes/smartthings/aeon-multisensor.src/.st-ignore

@@ -1,2 +0,0 @@
-.st-ignore
-README.md

devicetypes/smartthings/aeon-multisensor.src/README.md

@@ -1,48 +0,0 @@
-# Aeon Multisensor
-
-Cloud Execution
-
-Works with: 
-
-* [Aeotec MultiSensor (DSB05-ZWUS)](https://www.smartthings.com/products/aeotec-multisensor-5)
-
-## Table of contents
-
-* [Capabilities](#capabilities)
-* [Health](#device-health)
-* [Battery](#battery-specification)
-* [Troubleshooting](#troubleshooting)
-
-## Capabilities
-
-* **Motion Sensor** - can detect motion
-* **Temperature Measurement** - defines device measures current temperature
-* **Relative Humidity Measurement** - allow reading the relative humidity from devices that support it
-* **Illuminance Measurement** - gives the illuminance reading from devices that support it
-* **Configuration** - _configure()_ command called when device is installed or device preferences updated
-* **Sensor** - detects sensor events
-* **Battery** - defines device uses a battery
-* **Health Check** - indicates ability to get device health notifications
-
-
-## Device Health
-
-Aeon Labs MultiSensor is polled by the hub.
-As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
-Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
-Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
-the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
-it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
-
-* __32min__ checkInterval
-
-## Battery Specification
-
-Four AAA batteries are required.
-
-## Troubleshooting
-
-If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
-Pairing needs to be tried again by placing the device closer to the hub.
-Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
-* [Aeon MultiSensor Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/206157226-How-to-connect-Aeon-Labs-MultiSensors)

devicetypes/smartthings/aeon-multisensor.src/aeon-multisensor.groovy

@@ -20,7 +20,6 @@ metadata {
 		capability "Illuminance Measurement"
 		capability "Sensor"
 		capability "Battery"
-		capability "Health Check"
 
 		fingerprint deviceId: "0x2001", inClusters: "0x30,0x31,0x80,0x84,0x70,0x85,0x72,0x86"
 	}
@@ -94,16 +93,6 @@ metadata {
 	}
 }
 
-def installed(){
-// Device-Watch simply pings if no device events received for 32min(checkInterval)
-	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
-}
-
-def updated(){
-// Device-Watch simply pings if no device events received for 32min(checkInterval)
-	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
-}
-
 // Parse incoming device messages to generate events
 def parse(String description)
 {
@@ -190,13 +179,6 @@ def zwaveEvent(physicalgraph.zwave.Command cmd) {
 	[:]
 }
 
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-	secure(zwave.batteryV1.batteryGet())
-}
-
 def configure() {
 	delayBetween([
 		// send binary sensor report instead of basic set for motion

smartapps/smartthings/big-turn-off.src/big-turn-off.groovy

@@ -51,4 +51,4 @@ def changedLocationMode(evt) {
 def appTouch(evt) {
 	log.debug "appTouch: $evt"
 	switches?.off()
-}
+}