Merge pull request #1469 from SmartThingsCommunity/staging

Rolling up staging for production deploy

devicetypes/smartthings/centralite-dimmer.src/centralite-dimmer.groovy

@@ -1,96 +0,0 @@
-/**
- *  Copyright 2015 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- *	CentraLite Dimmer
- *
- *	Author: SmartThings
- *	Date: 2013-12-04
- */
-//DEPRECATED - Using the generic DTH for this device. Users need to be moved before deleting this DTH
-metadata {
-	definition (name: "CentraLite Dimmer", namespace: "smartthings", author: "SmartThings") {
-		capability "Switch Level"
-		capability "Actuator"
-		capability "Switch"
-		capability "Power Meter"
-		capability "Configuration"
-		capability "Refresh"
-		capability "Sensor"
-
-	}
-
-	tiles(scale: 2) {
-		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-				attributeState "on", label:'${name}', action:"switch.off", icon:"st.switches.switch.on", backgroundColor:"#79b821", nextState:"turningOff"
-				attributeState "off", label:'${name}', action:"switch.on", icon:"st.switches.switch.off", backgroundColor:"#ffffff", nextState:"turningOn"
-				attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.switches.switch.on", backgroundColor:"#79b821", nextState:"turningOff"
-				attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.switches.switch.off", backgroundColor:"#ffffff", nextState:"turningOn"
-			}
-			tileAttribute ("device.level", key: "SLIDER_CONTROL") {
-				attributeState "level", action:"switch level.setLevel"
-			}
-			tileAttribute ("power", key: "SECONDARY_CONTROL") {
-				attributeState "power", label:'${currentValue} W'
-			}
-		}
-		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-		}
-		main "switch"
-		details(["switch", "refresh"])
-	}
-}
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-	log.debug "description is $description"
-
-	def event = zigbee.getEvent(description)
-	if (event) {
-		log.info event
-		if (event.name == "power") {
-			if (device.getDataValue("manufacturer") != "OSRAM") {       //OSRAM devices do not reliably update power
-				event.value = (event.value as Integer) / 10             //TODO: The divisor value needs to be set as part of configuration
-				sendEvent(event)
-			}
-		}
-		else {
-			sendEvent(event)
-		}
-	}
-	else {
-		log.warn "DID NOT PARSE MESSAGE for description : $description"
-		log.debug zigbee.parseDescriptionAsMap(description)
-	}
-}
-
-def off() {
-	zigbee.off()
-}
-
-def on() {
-	zigbee.on()
-}
-
-def setLevel(value) {
-	zigbee.setLevel(value)
-}
-
-def refresh() {
-	zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
-}
-
-def configure() {
-	log.debug "Configuring Reporting and Bindings."
-	refresh()
-}

devicetypes/smartthings/cree-bulb.src/README.md

@@ -1,6 +1,6 @@
 # Connected Cree LED Bulb
 
-
+Cloud Execution
 
 Works with: 
 
@@ -23,8 +23,10 @@ Works with:
 
 ## Device Health
 
-A Category C6 Connected Cree LED Bulb with maxReportTime of 5 mins.
-Check-in interval = 12 mins
+Connected Cree LED Bulb with cloud polling it every __5min__
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+* __12min__ checkInterval
 
 ## Troubleshooting
 

devicetypes/smartthings/cree-bulb.src/cree-bulb.groovy

@@ -105,7 +105,7 @@ def healthPoll() {
 def configure() {
     unschedule()
     runEvery5Minutes("healthPoll")
-    // Device-Watch allows 2 check-in misses from device
+    // Device-Watch allows 2 check-in misses from device + ping
     sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
     zigbee.onOffRefresh() + zigbee.levelRefresh()
 }

devicetypes/smartthings/dimmer-switch.src/README.md

@@ -1,6 +1,6 @@
 # Z-wave Dimmer Switch
 
-
+Local Execution on V2 Hubs
 
 Works with:
 
@@ -34,6 +34,8 @@ Not to mention after going OFFLINE when the device is plugged back in, it might
 the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
 it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
 
+* __32min__ checkInterval
+
 ## Troubleshooting
 
 If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.

devicetypes/smartthings/ecobee-thermostat.src/ecobee-thermostat.groovy

@@ -23,6 +23,7 @@ metadata {
 		capability "Sensor"
 		capability "Refresh"
 		capability "Relative Humidity Measurement"
+		capability "Health Check"
 
 		command "generateEvent"
 		command "raiseSetpoint"
@@ -38,6 +39,7 @@ metadata {
 		attribute "maxCoolingSetpoint", "number"
 		attribute "minCoolingSetpoint", "number"
 		attribute "deviceTemperatureUnit", "string"
+		attribute "deviceAlive", "enum", ["true", "false"]
 	}
 
 	tiles {
@@ -120,6 +122,21 @@ metadata {
 
 }
 
+void installed() {
+    // The device refreshes every 5 minutes by default so if we miss 2 refreshes we can consider it offline
+    // Using 12 minutes because in testing, device health team found that there could be "jitter"
+    sendEvent(name: "checkInterval", value: 60 * 12, data: [protocol: "cloud"], displayed: false)
+}
+
+// Device Watch will ping the device to proactively determine if the device has gone offline
+// If the device was online the last time we refreshed, trigger another refresh as part of the ping.
+def ping() {
+    def isAlive = device.currentValue("deviceAlive") == "true" ? true : false
+    if (isAlive) {
+        refresh()
+    }
+}
+
 // parse events into attributes
 def parse(String description) {
 	log.debug "Parsing '${description}'"
@@ -164,7 +181,11 @@ def generateEvent(Map results) {
 			}  else if (name=="humidity") {
 				isChange = isStateChange(device, name, value.toString())
 				event << [value: value.toString(), isStateChange: isChange, displayed: false, unit: "%"]
-			}  else {
+			} else if (name == "deviceAlive") {
+				isChange = isStateChange(device, name, value.toString())
+				event['isStateChange'] = isChange
+				event['displayed'] = false
+			} else {
 				isChange = isStateChange(device, name, value.toString())
 				isDisplayed = isChange
 				event << [value: value.toString(), isStateChange: isChange, displayed: isDisplayed]

devicetypes/smartthings/ge-link-bulb.src/ge-link-bulb.groovy

@@ -87,7 +87,7 @@ metadata {
 def parse(String description) {
     def resultMap = zigbee.getEvent(description)
     if (resultMap) {
-        if ((resultMap.name == "level" && state.trigger == "setLevel") || resultMap.name != "level") {  //doing this to account for weird level reporting bug with GE Link Bulbs
+        if (resultMap.name != "level" || resultMap.value != 0) {  // Ignore level reports of 0 sent when bulb turns off
             sendEvent(resultMap)
         }
     }
@@ -188,12 +188,10 @@ def updated() {
 }
 
 def on() {
-    state.trigger = "on/off"
     zigbee.on()
 }
 
 def off() {
-    state.trigger = "on/off"
     zigbee.off()
 }
 
@@ -206,7 +204,6 @@ def refresh() {
 }
 
 def setLevel(value) {
-    state.trigger = "setLevel"
     def cmd
     def delayForRefresh = 500
     if (dimRate && (state?.rate != null)) {

devicetypes/smartthings/ge-zigbee-dimmer.src/ge-zigbee-dimmer.groovy

@@ -1,96 +0,0 @@
-/**
- *  Copyright 2015 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- *	    GE/Jasco ZigBee Dimmer
- *
- *	Author: SmartThings
- *	Date: 2015-07-01
- */
-
-metadata {
-	definition (name: "GE ZigBee Dimmer", namespace: "smartthings", author: "SmartThings") {
-		capability "Switch"
-		capability "Switch Level"
-		capability "Power Meter"
-		capability "Configuration"
-		capability "Refresh"
-		capability "Actuator"
-		capability "Sensor"
-
-	}
-
-	tiles(scale: 2) {
-		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-				attributeState "on", label:'${name}', action:"switch.off", icon:"st.switches.switch.on", backgroundColor:"#79b821", nextState:"turningOff"
-				attributeState "off", label:'${name}', action:"switch.on", icon:"st.switches.switch.off", backgroundColor:"#ffffff", nextState:"turningOn"
-				attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.switches.switch.on", backgroundColor:"#79b821", nextState:"turningOff"
-				attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.switches.switch.off", backgroundColor:"#ffffff", nextState:"turningOn"
-			}
-			tileAttribute ("device.level", key: "SLIDER_CONTROL") {
-				attributeState "level", action:"switch level.setLevel"
-			}
-			tileAttribute ("power", key: "SECONDARY_CONTROL") {
-				attributeState "power", label:'${currentValue} W'
-			}
-		}
-		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-		}
-		main "switch"
-		details(["switch", "refresh"])
-	}
-}
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-	log.debug "description is $description"
-
-	def event = zigbee.getEvent(description)
-	if (event) {
-		log.info event
-		if (event.name == "power") {
-			if (device.getDataValue("manufacturer") != "OSRAM") {       //OSRAM devices do not reliably update power
-				event.value = (event.value as Integer) / 10             //TODO: The divisor value needs to be set as part of configuration
-				sendEvent(event)
-			}
-		}
-		else {
-			sendEvent(event)
-		}
-	}
-	else {
-		log.warn "DID NOT PARSE MESSAGE for description : $description"
-		log.debug zigbee.parseDescriptionAsMap(description)
-	}
-}
-
-def off() {
-	zigbee.off()
-}
-
-def on() {
-	zigbee.on()
-}
-
-def setLevel(value) {
-	zigbee.setLevel(value)
-}
-
-def refresh() {
-	zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
-}
-
-def configure() {
-	log.debug "Configuring Reporting and Bindings."
-	refresh()
-}

devicetypes/smartthings/ge-zigbee-switch.src/ge-zigbee-switch.groovy

@@ -1,86 +0,0 @@
-/**
- *  Copyright 2015 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- *	    GE/Jasco ZigBee Switch
- *
- *	Author: SmartThings
- *	Date: 2015-07-01
- */
-
-metadata {
-	// Automatically generated. Make future change here.
-	definition (name: "GE ZigBee Switch", namespace: "smartthings", author: "SmartThings") {
-		capability "Switch"
-		capability "Power Meter"
-		capability "Configuration"
-		capability "Refresh"
-		capability "Actuator"
-		capability "Sensor"
-
-	}
-
-	tiles(scale: 2) {
-		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-				attributeState "on", label:'${name}', action:"switch.off", icon:"st.switches.switch.on", backgroundColor:"#79b821", nextState:"turningOff"
-				attributeState "off", label:'${name}', action:"switch.on", icon:"st.switches.switch.off", backgroundColor:"#ffffff", nextState:"turningOn"
-				attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.switches.switch.on", backgroundColor:"#79b821", nextState:"turningOff"
-				attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.switches.switch.off", backgroundColor:"#ffffff", nextState:"turningOn"
-			}
-			tileAttribute ("power", key: "SECONDARY_CONTROL") {
-				attributeState "power", label:'${currentValue} W'
-			}
-		}
-		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-		}
-		main "switch"
-		details(["switch", "refresh"])
-	}
-}
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-	log.debug "description is $description"
-	def event = zigbee.getEvent(description)
-	if (event) {
-		if (event.name == "power") {
-			def powerValue
-			powerValue = (event.value as Integer)/10            //TODO: The divisor value needs to be set as part of configuration
-			sendEvent(name: "power", value: powerValue)
-		}
-		else {
-			sendEvent(event)
-		}
-	}
-	else {
-		log.warn "DID NOT PARSE MESSAGE for description : $description"
-		log.debug zigbee.parseDescriptionAsMap(description)
-	}
-}
-
-def off() {
-	zigbee.off()
-}
-
-def on() {
-	zigbee.on()
-}
-
-def refresh() {
-	zigbee.onOffRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
-}
-
-def configure() {
-	log.debug "Configuring Reporting and Bindings."
-	refresh()
-}

devicetypes/smartthings/nyce-open-closed-sensor.src/README.md

@@ -1,6 +1,6 @@
 # Nyce Door/Window Sensor (Open/Close Sensor)
 
-
+Cloud Execution
 
 Works with:
 
@@ -23,7 +23,11 @@ Works with:
 
 ## Device Health
 
-A Category C2 Nyce Door/Window sensor that has 12min check-in interval
+Nyce Door/Window sensor with reporting interval of 5 min.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+ 
+* __12min__ checkInterval
+
 
 ## Battery Specification
 

devicetypes/smartthings/osram-lightify-gardenspot-mini-rgb.src/osram-lightify-gardenspot-mini-rgb.groovy

@@ -1,145 +0,0 @@
-/*
-    Osram Lightify Gardenspot Mini RGB
-
-    Osram bulbs have a firmware issue causing it to forget its dimming level when turned off (via commands). Handling
-    that issue by using state variables
-*/
-
-metadata {
-    definition (name: "OSRAM LIGHTIFY Gardenspot mini RGB", namespace: "smartthings", author: "SmartThings") {
-
-        capability "Color Temperature"
-        capability "Actuator"
-        capability "Switch"
-        capability "Switch Level"
-        capability "Configuration"
-        capability "Polling"
-        capability "Refresh"
-        capability "Sensor"
-        capability "Color Control"
-
-        attribute "colorName", "string"
-
-        command "setAdjustedColor"
-    }
-
-    // UI tile definitions
-    tiles(scale: 2) {
-        multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-            tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-                attributeState "on", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "off", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
-                attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
-            }
-            tileAttribute ("device.level", key: "SLIDER_CONTROL") {
-                attributeState "level", action:"switch level.setLevel"
-            }
-            tileAttribute ("device.color", key: "COLOR_CONTROL") {
-                attributeState "color", action:"color control.setColor"
-            }
-        }
-        standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-        }
-
-        main(["switch"])
-        details(["switch", "refresh"])
-    }
-}
-
-//Globals
-private getATTRIBUTE_HUE() { 0x0000 }
-private getATTRIBUTE_SATURATION() { 0x0001 }
-private getHUE_COMMAND() { 0x00 }
-private getSATURATION_COMMAND() { 0x03 }
-private getCOLOR_CONTROL_CLUSTER() { 0x0300 }
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-    log.debug "description is $description"
-
-    def event = zigbee.getEvent(description)
-    if (event) {
-        log.debug event
-        if (event.name=="level" && event.value==0) {}
-        else {
-            sendEvent(event)
-        }
-    }
-    else {
-        def zigbeeMap = zigbee.parseDescriptionAsMap(description)
-        def cluster = zigbee.parse(description)
-
-        if (zigbeeMap?.clusterInt == COLOR_CONTROL_CLUSTER) {
-            if(zigbeeMap.attrInt == ATTRIBUTE_HUE){  //Hue Attribute
-                def hueValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
-                sendEvent(name: "hue", value: hueValue, descriptionText: "Color has changed")
-            }
-            else if(zigbeeMap.attrInt == ATTRIBUTE_SATURATION){ //Saturation Attribute
-                def saturationValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
-                sendEvent(name: "saturation", value: saturationValue, descriptionText: "Color has changed", displayed: false)
-            }
-        }
-        else if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
-            if (cluster.data[0] == 0x00){
-                log.debug "ON/OFF REPORTING CONFIG RESPONSE: $cluster"
-                sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-            }
-            else {
-                log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
-            }
-        }
-        else {
-            log.info "DID NOT PARSE MESSAGE for description : $description"
-            log.debug zigbeeMap
-        }
-    }
-}
-
-def on() {
-    zigbee.on()
-}
-
-def off() {
-    zigbee.off()
-}
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-    return zigbee.onOffRefresh()
-}
-
-def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION) + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
-}
-
-def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
-    // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-
-    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01) + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
-}
-
-def setLevel(value) {
-    zigbee.setLevel(value)
-}
-
-def setColor(value){
-    log.trace "setColor($value)"
-    zigbee.on() + setHue(value.hue) + "delay 500" + setSaturation(value.saturation)
-}
-
-def setHue(value) {
-    def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500")       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
-}
-
-def setSaturation(value) {
-    def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + "delay 1000" + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
-}

devicetypes/smartthings/osram-lightify-led-flexible-strip-rgbw.src/osram-lightify-led-flexible-strip-rgbw.groovy

@@ -1,183 +0,0 @@
-/*
-    Osram Flex RGBW Light Strip
-
-    Osram bulbs have a firmware issue causing it to forget its dimming level when turned off (via commands). Handling
-    that issue by using state variables
-*/
-//DEPRECATED - Using the generic DTH for this device. Users need to be moved before deleting this DTH
-
-metadata {
-	definition (name: "OSRAM LIGHTIFY LED Flexible Strip RGBW", namespace: "smartthings", author: "SmartThings") {
-
-        capability "Color Temperature"
-        capability "Actuator"
-        capability "Switch"
-		capability "Switch Level"
-		capability "Configuration"
-		capability "Polling"
-		capability "Refresh"
-		capability "Sensor"
-		capability "Color Control"
-
-        attribute "colorName", "string"
-
-        command "setAdjustedColor"
-
-
-		//fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY Flex RGBW"
-        //fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Flex RGBW"
-
-    }
-
-    // UI tile definitions
-    tiles(scale: 2) {
-        multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-            tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-                attributeState "on", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "off", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
-                attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
-            }
-            tileAttribute ("device.level", key: "SLIDER_CONTROL") {
-                attributeState "level", action:"switch level.setLevel"
-            }
-            tileAttribute ("device.color", key: "COLOR_CONTROL") {
-                attributeState "color", action:"color control.setColor"
-            }
-        }
-        controlTile("colorTempSliderControl", "device.colorTemperature", "slider", width: 4, height: 2, inactiveLabel: false, range:"(2700..6500)") {
-            state "colorTemperature", action:"color temperature.setColorTemperature"
-        }
-        valueTile("colorName", "device.colorName", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "colorName", label: '${currentValue}'
-        }
-        standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-        }
-
-        main(["switch"])
-        details(["switch", "colorTempSliderControl", "colorName", "refresh"])
-    }
-}
-
-//Globals
-private getATTRIBUTE_HUE() { 0x0000 }
-private getATTRIBUTE_SATURATION() { 0x0001 }
-private getHUE_COMMAND() { 0x00 }
-private getSATURATION_COMMAND() { 0x03 }
-private getCOLOR_CONTROL_CLUSTER() { 0x0300 }
-private getATTRIBUTE_COLOR_TEMPERATURE() { 0x0007 }
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-    log.debug "description is $description"
-
-    def event = zigbee.getEvent(description)
-    if (event) {
-        log.debug event
-        if (event.name=="level" && event.value==0) {}
-        else {
-            if (event.name=="colorTemperature") {
-                setGenericName(event.value)
-            }
-            sendEvent(event)
-        }
-    }
-    else {
-        def zigbeeMap = zigbee.parseDescriptionAsMap(description)
-        def cluster = zigbee.parse(description)
-
-        if (zigbeeMap?.clusterInt == COLOR_CONTROL_CLUSTER) {
-            if(zigbeeMap.attrInt == ATTRIBUTE_HUE){  //Hue Attribute
-                def hueValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
-                sendEvent(name: "hue", value: hueValue, descriptionText: "Color has changed")
-            }
-            else if(zigbeeMap.attrInt == ATTRIBUTE_SATURATION){ //Saturation Attribute
-                def saturationValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
-                sendEvent(name: "saturation", value: saturationValue, descriptionText: "Color has changed", displayed: false)
-            }
-        }
-        else if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
-            if (cluster.data[0] == 0x00){
-                log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
-                sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-            }
-            else {
-                log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
-            }
-        }
-        else {
-            log.info "DID NOT PARSE MESSAGE for description : $description"
-            log.debug zigbeeMap
-        }
-    }
-}
-
-def on() {
-    zigbee.on()
-}
-
-def off() {
-    zigbee.off()
-}
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-    return zigbee.onOffRefresh()
-}
-
-def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_COLOR_TEMPERATURE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION) + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
-}
-
-def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
-    // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-
-    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    refresh()
-}
-
-def setColorTemperature(value) {
-    setGenericName(value)
-    zigbee.setColorTemperature(value)
-}
-
-//Naming based on the wiki article here: http://en.wikipedia.org/wiki/Color_temperature
-def setGenericName(value){
-    if (value != null) {
-        def genericName = "White"
-        if (value < 3300) {
-            genericName = "Soft White"
-        } else if (value < 4150) {
-            genericName = "Moonlight"
-        } else if (value <= 5000) {
-            genericName = "Cool White"
-        } else if (value >= 5000) {
-            genericName = "Daylight"
-        }
-        sendEvent(name: "colorName", value: genericName)
-    }
-}
-
-def setLevel(value) {
-    zigbee.setLevel(value)
-}
-
-def setColor(value){
-    log.trace "setColor($value)"
-    zigbee.on() + setHue(value.hue) + "delay 300" + setSaturation(value.saturation)
-}
-
-def setHue(value) {
-    def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500")       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
-}
-
-def setSaturation(value) {
-    def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + "delay 1000" + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
-}

devicetypes/smartthings/osram-lightify-led-tunable-white-60w.src/osram-lightify-led-tunable-white-60w.groovy

@@ -1,139 +0,0 @@
-/*
-    Osram Tunable White 60 A19 bulb
-
-    Osram bulbs have a firmware issue causing it to forget its dimming level when turned off (via commands). Handling
-    that issue by using state variables
-*/
-
-//DEPRECATED - Using the generic DTH for this device. Users need to be moved before deleting this DTH
-
-metadata {
-    definition (name: "OSRAM LIGHTIFY LED Tunable White 60W", namespace: "smartthings", author: "SmartThings") {
-
-        capability "Color Temperature"
-        capability "Actuator"
-        capability "Switch"
-        capability "Switch Level"
-        capability "Configuration"
-        capability "Refresh"
-        capability "Sensor"
-
-        attribute "colorName", "string"
-    }
-
-    // UI tile definitions
-    tiles(scale: 2) {
-        multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-            tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-                attributeState "on", label:'${name}', action:"switch.off", icon:"st.switches.light.on", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "off", label:'${name}', action:"switch.on", icon:"st.switches.light.off", backgroundColor:"#ffffff", nextState:"turningOn"
-                attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.switches.light.on", backgroundColor:"#79b821", nextState:"turningOff"
-                attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.switches.light.off", backgroundColor:"#ffffff", nextState:"turningOn"
-            }
-            tileAttribute ("device.level", key: "SLIDER_CONTROL") {
-                attributeState "level", action:"switch level.setLevel"
-            }
-        }
-
-        standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-        }
-
-        controlTile("colorTempSliderControl", "device.colorTemperature", "slider", width: 4, height: 2, inactiveLabel: false, range:"(2700..6500)") {
-            state "colorTemperature", action:"color temperature.setColorTemperature"
-        }
-        valueTile("colorName", "device.colorName", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-            state "colorName", label: '${currentValue}'
-        }
-
-        main(["switch"])
-        details(["switch", "colorTempSliderControl", "colorName", "refresh"])
-    }
-}
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-    log.debug "description is $description"
-    def event = zigbee.getEvent(description)
-    if (event) {
-        if (event.name=="level" && event.value==0) {}
-        else {
-            if (event.name=="colorTemperature") {
-                setGenericName(event.value)
-            }
-            sendEvent(event)
-        }
-    }
-    else {
-        def cluster = zigbee.parse(description)
-
-        if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
-            if (cluster.data[0] == 0x00) {
-                log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
-                sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-            }
-            else {
-                log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
-            }
-        }
-        else {
-            log.warn "DID NOT PARSE MESSAGE for description : $description"
-            log.debug "${cluster}"
-        }
-    }
-}
-
-def off() {
-    zigbee.off()
-}
-
-def on() {
-    zigbee.on()
-}
-
-def setLevel(value) {
-    zigbee.setLevel(value)
-}
-
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-    return zigbee.onOffRefresh()
-}
-
-def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig()
-}
-
-def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
-    // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-
-    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    refresh()
-}
-
-def setColorTemperature(value) {
-    setGenericName(value)
-    zigbee.setColorTemperature(value)
-}
-
-//Naming based on the wiki article here: http://en.wikipedia.org/wiki/Color_temperature
-def setGenericName(value){
-    if (value != null) {
-        def genericName = "White"
-        if (value < 3300) {
-            genericName = "Soft White"
-        } else if (value < 4150) {
-            genericName = "Moonlight"
-        } else if (value <= 5000) {
-            genericName = "Cool White"
-        } else if (value >= 5000) {
-            genericName = "Daylight"
-        }
-        sendEvent(name: "colorName", value: genericName)
-    }
-}

devicetypes/smartthings/smartpower-dimming-outlet.src/smartpower-dimming-outlet.groovy

@@ -69,15 +69,17 @@ metadata {
 def parse(String description) {
 	log.debug "description is $description"
 
+	def event = [:]
 	def finalResult = isKnownDescription(description)
-	if (finalResult != "false") {
+	if (finalResult) {
 		log.info finalResult
 		if (finalResult.type == "update") {
 			log.info "$device updates: ${finalResult.value}"
+			event = null
 		}
 		else if (finalResult.type == "power") {
 			def powerValue = (finalResult.value as Integer)/10
-			sendEvent(name: "power", value: powerValue)
+			event = createEvent(name: "power", value: powerValue)
 
 			/*
 				Dividing by 10 as the Divisor is 10000 and unit is kW for the device. AttrId: 0302 and 0300. Simplifying to 10
@@ -87,13 +89,14 @@ def parse(String description) {
 			*/
 		}
 		else {
-			sendEvent(name: finalResult.type, value: finalResult.value)
+			event = createEvent(name: finalResult.type, value: finalResult.value)
 		}
 	}
 	else {
 		log.warn "DID NOT PARSE MESSAGE for description : $description"
 		log.debug parseDescriptionAsMap(description)
 	}
+	return event
 }
 
 // Commands to device
@@ -209,13 +212,16 @@ def isKnownDescription(description) {
 		else if (descMap.cluster == "0B04" || descMap.clusterId == "0B04"){
 			isDescriptionPower(descMap)
 		}
+		else {
+			return [:]
+		}
 	}
 	else if(description?.startsWith("on/off:")) {
 		def switchValue = description?.endsWith("1") ? "on" : "off"
 		return	[type: "switch", value : switchValue]
 	}
 	else {
-		return "false"
+		return [:]
 	}
 }
 
@@ -249,7 +255,7 @@ def isDescriptionOnOff(descMap) {
 		return	[type: "switch", value : switchValue]
 	}
 	else {
-		return "false"
+		return [:]
 	}
 
 }
@@ -276,10 +282,9 @@ def isDescriptionLevel(descMap) {
 
 	if (dimmerValue != -1){
 		return	[type: "level", value : dimmerValue]
-
 	}
 	else {
-		return "false"
+		return [:]
 	}
 }
 
@@ -301,7 +306,7 @@ def isDescriptionPower(descMap) {
 		return	[type: "power", value : powerValue]
 	}
 	else {
-		return "false"
+		return [:]
 	}
 }
 

devicetypes/smartthings/smartpower-outlet.src/README.md

@@ -1,6 +1,6 @@
 # SmartPower Outlet
 
-
+Local Execution on V2 Hubs
 
 Works with: 
 
@@ -23,10 +23,11 @@ Works with:
 
 ## Device Health
 
-A Category C1 smart power outlet with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime. 
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 mins
+SmartPower outlet with reporting interval of 5 mins
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+* V1, TV, HubV2 AppEngine < 1.5.1 - __21min__ checkInterval
+* HubV2 AppEngine 1.5.1 - __12min__ checkInterval
 
 ## Troubleshooting
 

devicetypes/smartthings/smartpower-outlet.src/smartpower-outlet.groovy

@@ -79,6 +79,7 @@ def parse(String description) {
 	log.debug "description is $description"
 
 	def finalResult = zigbee.getKnownDescription(description)
+	def event = [:]
 
 	//TODO: Remove this after getKnownDescription can parse it automatically
 	if (!finalResult && description!="updated")
@@ -88,10 +89,11 @@ def parse(String description) {
 		log.info "final result = $finalResult"
 		if (finalResult.type == "update") {
 			log.info "$device updates: ${finalResult.value}"
+			event = null
 		}
 		else if (finalResult.type == "power") {
 			def powerValue = (finalResult.value as Integer)/10
-			sendEvent(name: "power", value: powerValue, descriptionText: '{{ device.displayName }} power is {{ value }} Watts', translatable: true )
+			event = createEvent(name: "power", value: powerValue, descriptionText: '{{ device.displayName }} power is {{ value }} Watts', translatable: true)
 			/*
 				Dividing by 10 as the Divisor is 10000 and unit is kW for the device. AttrId: 0302 and 0300. Simplifying to 10
 				power level is an integer. The exact power level with correct units needs to be handled in the device type
@@ -100,7 +102,7 @@ def parse(String description) {
 		}
 		else {
 			def descriptionText = finalResult.value == "on" ? '{{ device.displayName }} is On' : '{{ device.displayName }} is Off'
-			sendEvent(name: finalResult.type, value: finalResult.value, descriptionText: descriptionText, translatable: true)
+			event = createEvent(name: finalResult.type, value: finalResult.value, descriptionText: descriptionText, translatable: true)
 		}
 	}
 	else {
@@ -109,10 +111,11 @@ def parse(String description) {
 		if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07){
 			if (cluster.data[0] == 0x00) {
 				log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
-				sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+				event = createEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 			}
 			else {
 				log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+				event = null
 			}
 		}
 		else {
@@ -120,6 +123,7 @@ def parse(String description) {
 			log.debug "${cluster}"
 		}
 	}
+	return event
 }
 
 def off() {
@@ -141,9 +145,9 @@ def refresh() {
 }
 
 def configure() {
-	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+	sendEvent(name: "checkInterval", value: 2 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	// OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
 	refresh() + zigbee.onOffConfig(0, 300) + powerConfig()

devicetypes/smartthings/smartsense-garage-door-multi.src/smartsense-garage-door-multi.groovy

@@ -86,7 +86,7 @@ metadata {
 
 def parse(String description) {
 	log.debug "parse($description)"
-	def results = null
+	def results = [:]
 
 	if (!isSupportedDescription(description) || zigbee.isZoneType19(description)) {
 		// Ignore this in favor of orientation-based state

devicetypes/smartthings/smartsense-moisture-sensor.src/README.md

@@ -1,6 +1,6 @@
 # Smartsense Moisture Sensor
 
-
+Local Execution on V2 Hubs
 
 Works with: 
 
@@ -23,10 +23,11 @@ Works with:
 
 ## Device Health
 
-A Category C2 moisture sensor with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime. 
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 mins
+SmartSense Moisture sensor with reporting interval of 5 mins.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+* V1, TV, HubV2 AppEngine < 1.5.1 - __121min__ checkInterval
+* HubV2 AppEngine 1.5.1 - __12min__ checkInterval
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy

@@ -102,7 +102,7 @@ def parse(String description) {
 	}
 
 	log.debug "Parse returned $map"
-	def result = map ? createEvent(map) : null
+	def result = map ? createEvent(map) : [:]
 
 	if (description?.startsWith('enroll request')) {
 		List cmds = enrollResponse()
@@ -293,9 +293,9 @@ def refresh() {
 }
 
 def configure() {
-	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+	sendEvent(name: "checkInterval", value: 2 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default

devicetypes/smartthings/smartsense-motion-sensor.src/README.md

@@ -1,6 +1,6 @@
 # Smartsense Motion Sensor
 
-
+Local Execution on V2 Hubs
 
 Works with: 
 
@@ -22,10 +22,12 @@ Works with:
 
 ## Device Health
 
-A Category C2 motion sensor with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime.
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 mins
+SmartSense Motion sensor with reporting interval of 5 mins.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+* V1, TV, HubV2 AppEngine < 1.5.1 - __121min__ checkInterval
+* HubV2 AppEngine 1.5.1 - __12min__ checkInterval
+
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy

@@ -106,7 +106,7 @@ def parse(String description) {
 	}
 
 	log.debug "Parse returned $map"
-	def result = map ? createEvent(map) : null
+	def result = map ? createEvent(map) : [:]
 
 	if (description?.startsWith('enroll request')) {
 		List cmds = enrollResponse()
@@ -306,9 +306,9 @@ def refresh() {
 }
 
 def configure() {
-	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+	sendEvent(name: "checkInterval", value: 2 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default

devicetypes/smartthings/smartsense-motion-temp-sensor.src/smartsense-motion-temp-sensor.groovy

@@ -1,328 +0,0 @@
-/**
- *  SmartSense Motion/Temp Sensor
- *
- *  Copyright 2014 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-
-//DEPRECATED - Using the smartsense-motion-sensor.groovy DTH for this device. Users need to be moved before deleting this DTH
-import physicalgraph.zigbee.clusters.iaszone.ZoneStatus
-
-metadata {
-	definition (name: "SmartSense Motion/Temp Sensor", namespace: "smartthings", author: "SmartThings") {
-		capability "Motion Sensor"
-		capability "Configuration"
-		capability "Battery"
-        capability "Temperature Measurement"
-		capability "Refresh"
-		capability "Sensor"
-
-        command "enrollResponse"
-
-	}
-
-	preferences {
-		section {
-			image(name: 'educationalcontent', multiple: true, images: [
-					"http://cdn.device-gse.smartthings.com/Motion/Motion1.jpg",
-					"http://cdn.device-gse.smartthings.com/Motion/Motion2.jpg",
-					"http://cdn.device-gse.smartthings.com/Motion/Motion3.jpg"
-			])
-		}
-		section {
-			input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter '-5'. If 3 degrees too cold, enter '+3'.", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-			input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
-		}
-	}
-
-	tiles(scale: 2) {
-		multiAttributeTile(name:"motion", type: "generic", width: 6, height: 4){
-			tileAttribute ("device.motion", key: "PRIMARY_CONTROL") {
-				attributeState "active", label:'motion', icon:"st.motion.motion.active", backgroundColor:"#53a7c0"
-				attributeState "inactive", label:'no motion', icon:"st.motion.motion.inactive", backgroundColor:"#ffffff"
-			}
-		}
-		valueTile("temperature", "device.temperature", width: 2, height: 2) {
-			state("temperature", label:'${currentValue}°', unit:"F",
-					backgroundColors:[
-							[value: 31, color: "#153591"],
-							[value: 44, color: "#1e9cbb"],
-							[value: 59, color: "#90d2a7"],
-							[value: 74, color: "#44b621"],
-							[value: 84, color: "#f1d801"],
-							[value: 95, color: "#d04e00"],
-							[value: 96, color: "#bc2323"]
-					]
-			)
-		}
-		valueTile("battery", "device.battery", decoration: "flat", inactiveLabel: false, width: 2, height: 2) {
-			state "battery", label:'${currentValue}% battery', unit:""
-		}
-		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-			state "default", action:"refresh.refresh", icon:"st.secondary.refresh"
-		}
-
-		main(["motion", "temperature"])
-		details(["motion", "temperature", "battery", "refresh"])
-	}
-}
-
-def parse(String description) {
-	log.debug "description: $description"
-
-	Map map = [:]
-	if (description?.startsWith('catchall:')) {
-		map = parseCatchAllMessage(description)
-	}
-	else if (description?.startsWith('read attr -')) {
-		map = parseReportAttributeMessage(description)
-	}
-	else if (description?.startsWith('temperature: ')) {
-		map = parseCustomMessage(description)
-	}
-	else if (description?.startsWith('zone status')) {
-		map = parseIasMessage(description)
-	}
-
-	log.debug "Parse returned $map"
-	def result = map ? createEvent(map) : null
-
-	if (description?.startsWith('enroll request')) {
-		List cmds = enrollResponse()
-		log.debug "enroll response: ${cmds}"
-		result = cmds?.collect { new physicalgraph.device.HubAction(it) }
-	}
-	return result
-}
-
-private Map parseCatchAllMessage(String description) {
-	Map resultMap = [:]
-	def cluster = zigbee.parse(description)
-	if (shouldProcessMessage(cluster)) {
-		switch(cluster.clusterId) {
-			case 0x0001:
-				// 0x07 - configure reporting
-				if (cluster.command != 0x07) {
-					resultMap = getBatteryResult(cluster.data.last())
-				}
-				break
-
-			case 0x0402:
-				if (cluster.command == 0x07) {
-					if (cluster.data[0] == 0x00) {
-						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-					}
-					else {
-						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
-					}
-
-				}
-				else {
-					// temp is last 2 data values. reverse to swap endian
-					String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
-					def value = getTemperature(temp)
-					resultMap = getTemperatureResult(value)
-				}
-				break
-
-			case 0x0406:
-				// 0x07 - configure reporting
-				if (cluster.command != 0x07) {
-					log.debug 'motion'
-					resultMap.name = 'motion'
-				}
-				break
-		}
-	}
-
-	return resultMap
-}
-
-private boolean shouldProcessMessage(cluster) {
-	// 0x0B is default response indicating message got through
-	boolean ignoredMessage = cluster.profileId != 0x0104 ||
-			cluster.command == 0x0B ||
-			(cluster.data.size() > 0 && cluster.data.first() == 0x3e)
-	return !ignoredMessage
-}
-
-private Map parseReportAttributeMessage(String description) {
-	Map descMap = (description - "read attr - ").split(",").inject([:]) { map, param ->
-		def nameAndValue = param.split(":")
-		map += [(nameAndValue[0].trim()):nameAndValue[1].trim()]
-	}
-	log.debug "Desc Map: $descMap"
-
-	Map resultMap = [:]
-	if (descMap.cluster == "0402" && descMap.attrId == "0000") {
-		def value = getTemperature(descMap.value)
-		resultMap = getTemperatureResult(value)
-	}
-	else if (descMap.cluster == "0001" && descMap.attrId == "0020") {
-		resultMap = getBatteryResult(Integer.parseInt(descMap.value, 16))
-	}
-	else if (descMap.cluster == "0406" && descMap.attrId == "0000") {
-		def value = descMap.value.endsWith("01") ? "active" : "inactive"
-		resultMap = getMotionResult(value)
-	}
-
-	return resultMap
-}
-
-private Map parseCustomMessage(String description) {
-	Map resultMap = [:]
-	if (description?.startsWith('temperature: ')) {
-		def value = zigbee.parseHATemperatureValue(description, "temperature: ", getTemperatureScale())
-		resultMap = getTemperatureResult(value)
-	}
-	return resultMap
-}
-
-private Map parseIasMessage(String description) {
-	ZoneStatus zs = zigbee.parseZoneStatus(description)
-
-	// Some sensor models that use this DTH use alarm1 and some use alarm2 to signify motion
-	return (zs.isAlarm1Set() || zs.isAlarm2Set()) ? getMotionResult('active') : getMotionResult('inactive')
-}
-
-def getTemperature(value) {
-	def celsius = Integer.parseInt(value, 16).shortValue() / 100
-	if(getTemperatureScale() == "C"){
-		return Math.round(celsius)
-	} else {
-		return Math.round(celsiusToFahrenheit(celsius))
-	}
-}
-
-private Map getBatteryResult(rawValue) {
-	log.debug 'Battery'
-	def linkText = getLinkText(device)
-
-	def result = [:]
-
-	def volts = rawValue / 10
-
-	if (!(rawValue == 0 || rawValue == 255)) {
-		def minVolts = 2.1
-		def maxVolts = 3.0
-		def pct = (volts - minVolts) / (maxVolts - minVolts)
-		def roundedPct = Math.round(pct * 100)
-		if (roundedPct <= 0)
-			roundedPct = 1
-		result.name = 'battery'
-		result.value = Math.min(100, roundedPct)
-		result.descriptionText = "${linkText} battery was ${result.value}%"
-
-	}
-
-	return result
-}
-
-private Map getTemperatureResult(value) {
-	log.debug 'TEMP'
-	if (tempOffset) {
-		def offset = tempOffset as int
-		def v = value as int
-		value = v + offset
-	}
-	def descriptionText
-	if ( temperatureScale == 'C' )
-		descriptionText = '{{ device.displayName }} was {{ value }}°C'
-	else
-		descriptionText = '{{ device.displayName }} was {{ value }}°F'
-
-	return [
-			name: 'temperature',
-			value: value,
-			descriptionText: descriptionText,
-			translatable: true,
-			unit: temperatureScale
-	]
-}
-
-private Map getMotionResult(value) {
-	log.debug 'motion'
-	String descriptionText = value == 'active' ? "{{ device.displayName }} detected motion" : "{{ device.displayName }} motion has stopped"
-	return [
-			name: 'motion',
-			value: value,
-			descriptionText: descriptionText,
-			translatable: true
-	]
-}
-
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-	return zigbee.readAttribute(0x001, 0x0020) // Read the Battery Level
-}
-
-def refresh() {
-	log.debug "refresh called"
-	def refreshCmds = [
-			"st rattr 0x${device.deviceNetworkId} 1 0x402 0", "delay 200",
-			"st rattr 0x${device.deviceNetworkId} 1 1 0x20", "delay 200"
-	]
-
-	return refreshCmds + enrollResponse()
-}
-
-def configure() {
-	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
-	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-
-	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
-	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	return refresh() + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) // send refresh cmds as part of config
-}
-
-def enrollResponse() {
-	log.debug "Sending enroll response"
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
-	[
-			//Resending the CIE in case the enroll request is sent before CIE is written
-			"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-			"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
-			//Enroll Response
-			"raw 0x500 {01 23 00 00 00}",
-			"send 0x${device.deviceNetworkId} 1 1", "delay 200"
-	]
-}
-
-private getEndpointId() {
-	new BigInteger(device.endpointId, 16).toString()
-}
-
-private hex(value) {
-	new BigInteger(Math.round(value).toString()).toString(16)
-}
-
-private String swapEndianHex(String hex) {
-	reverseArray(hex.decodeHex()).encodeHex()
-}
-
-private byte[] reverseArray(byte[] array) {
-	int i = 0;
-	int j = array.length - 1;
-	byte tmp;
-	while (j > i) {
-		tmp = array[j];
-		array[j] = array[i];
-		array[i] = tmp;
-		j--;
-		i++;
-	}
-	return array
-}

devicetypes/smartthings/smartsense-motion.src/smartsense-motion.groovy

@@ -44,7 +44,7 @@ metadata {
 }
 
 def parse(String description) {
-	def results
+	def results = [:]
 	if (isZoneType19(description) || !isSupportedDescription(description)) {
 		results = parseBasicMessage(description)
 	}
@@ -57,21 +57,25 @@ def parse(String description) {
 
 private Map parseBasicMessage(description) {
 	def name = parseName(description)
-	def value = parseValue(description)
-	def linkText = getLinkText(device)
-	def descriptionText = parseDescriptionText(linkText, value, description)
-	def handlerName = value
-	def isStateChange = isStateChange(device, name, value)
+	if (name != null) {
+		def value = parseValue(description)
+		def linkText = getLinkText(device)
+		def descriptionText = parseDescriptionText(linkText, value, description)
+		def handlerName = value
+		def isStateChange = isStateChange(device, name, value)
 
-	def results = [
-		name: name,
-		value: value,
-		linkText: linkText,
-		descriptionText: descriptionText,
-		handlerName: handlerName,
-		isStateChange: isStateChange,
-		displayed: displayed(description, isStateChange)
-	]
+		def results = [
+				name           : name,
+				value          : value,
+				linkText       : linkText,
+				descriptionText: descriptionText,
+				handlerName    : handlerName,
+				isStateChange  : isStateChange,
+				displayed      : displayed(description, isStateChange)
+		]
+	} else {
+		results = [:]
+	}
 	log.debug "Parse returned $results.descriptionText"
 	return results
 }

devicetypes/smartthings/smartsense-multi-sensor.src/README.md

@@ -1,6 +1,6 @@
 # Smartsense Multi Sensor
 
-
+Local Execution on V2 Hubs
 
 Works with: 
 
@@ -26,10 +26,11 @@ Works with:
 
 ## Device Health
 
-A Category C2 multi sensor with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime. 
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 mins
+SmartSense Multi sensor with reporting interval of 5 mins.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+* V1, TV, HubV2 AppEngine < 1.5.1 - __121min__ checkInterval
+* HubV2 AppEngine 1.5.1 - __12min__ checkInterval
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-multi-sensor.src/smartsense-multi-sensor.groovy

@@ -127,7 +127,7 @@ def parse(String description) {
 		map = parseIasMessage(description)
 	}
 
-	def result = map ? createEvent(map) : null
+	def result = map ? createEvent(map) : [:]
 
 	if (description?.startsWith('enroll request')) {
 		List cmds = enrollResponse()
@@ -400,9 +400,9 @@ def refresh() {
 }
 
 def configure() {
-	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+	sendEvent(name: "checkInterval", value: 2 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	log.debug "Configuring Reporting"
 

devicetypes/smartthings/smartsense-open-closed-accelerometer-sensor.src/smartsense-open-closed-accelerometer-sensor.groovy

@@ -1,503 +0,0 @@
-/**
- *  SmartSense Open/Closed Accelerometer Sensor
- *
- *  Copyright 2014 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-//DEPRECATED - Using the smartsense-multi-sensor.groovy DTH for this device. Users need to be moved before deleting this DTH
-import physicalgraph.zigbee.clusters.iaszone.ZoneStatus
-
-metadata {
-	definition (name: "SmartSense Open/Closed Accelerometer Sensor", namespace: "smartthings", author: "SmartThings", category: "C2") {
-		capability "Battery"
-		capability "Configuration"
-		capability "Contact Sensor"
-		capability "Acceleration Sensor"
-		capability "Refresh"
-		capability "Temperature Measurement"
-		capability "Health Check"
-		capability "Sensor"
-
-		command "enrollResponse"
-		attribute "status", "string"
-	}
-
-	preferences {
-		section {
-			image(name: 'educationalcontent', multiple: true, images: [
-					"http://cdn.device-gse.smartthings.com/Multi/Multi1.jpg",
-					"http://cdn.device-gse.smartthings.com/Multi/Multi2.jpg",
-					"http://cdn.device-gse.smartthings.com/Multi/Multi3.jpg",
-					"http://cdn.device-gse.smartthings.com/Multi/Multi4.jpg"
-			])
-		}
-		section {
-			input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter '-5'. If 3 degrees too cold, enter '+3'.", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-			input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
-		}
-		section {
-			input("garageSensor", "enum", title: "Do you want to use this sensor on a garage door?", description: "Tap to set", options: ["Yes", "No"], defaultValue: "No", required: false, displayDuringSetup: false)
-		}
-	}
-
-	tiles(scale: 2) {
-		multiAttributeTile(name:"status", type: "generic", width: 6, height: 4){
-			tileAttribute ("device.status", key: "PRIMARY_CONTROL") {
-				attributeState "open", label:'Open', icon:"st.contact.contact.open", backgroundColor:"#ffa81e"
-				attributeState "closed", label:'Closed', icon:"st.contact.contact.closed", backgroundColor:"#79b821"
-				attributeState "garage-open", label:'Open', icon:"st.doors.garage.garage-open", backgroundColor:"#ffa81e"
-				attributeState "garage-closed", label:'Closed', icon:"st.doors.garage.garage-closed", backgroundColor:"#79b821"
-			}
-		}
-		standardTile("contact", "device.contact", width: 2, height: 2) {
-			state("open", label:'Open', icon:"st.contact.contact.open", backgroundColor:"#ffa81e")
-			state("closed", label:'Closed', icon:"st.contact.contact.closed", backgroundColor:"#79b821")
-		}
-		standardTile("acceleration", "device.acceleration", width: 2, height: 2) {
-			state("active", label:'Active', icon:"st.motion.acceleration.active", backgroundColor:"#53a7c0")
-			state("inactive", label:'Inactive', icon:"st.motion.acceleration.inactive", backgroundColor:"#ffffff")
-		}
-		valueTile("temperature", "device.temperature", width: 2, height: 2) {
-			state("temperature", label:'${currentValue}°',
-					backgroundColors:[
-							[value: 31, color: "#153591"],
-							[value: 44, color: "#1e9cbb"],
-							[value: 59, color: "#90d2a7"],
-							[value: 74, color: "#44b621"],
-							[value: 84, color: "#f1d801"],
-							[value: 95, color: "#d04e00"],
-							[value: 96, color: "#bc2323"]
-					]
-			)
-		}
-		valueTile("battery", "device.battery", decoration: "flat", inactiveLabel: false, width: 2, height: 2) {
-			state "battery", label:'${currentValue}% battery', unit:""
-		}
-		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-			state "default", action:"refresh.refresh", icon:"st.secondary.refresh"
-		}
-
-
-		main(["status", "acceleration", "temperature"])
-		details(["status", "acceleration", "temperature", "battery", "refresh"])
-	}
-}
-
-def parse(String description) {
-	Map map = [:]
-	if (description?.startsWith('catchall:')) {
-		map = parseCatchAllMessage(description)
-	}
-	else if (description?.startsWith('temperature: ')) {
-		map = parseCustomMessage(description)
-	}
-	else if (description?.startsWith('zone status')) {
-		map = parseIasMessage(description)
-	}
-
-	def result = map ? createEvent(map) : null
-
-	if (description?.startsWith('enroll request')) {
-		List cmds = enrollResponse()
-		log.debug "enroll response: ${cmds}"
-		result = cmds?.collect { new physicalgraph.device.HubAction(it) }
-	}
-	else if (description?.startsWith('read attr -')) {
-		result = parseReportAttributeMessage(description).each { createEvent(it) }
-	}
-	return result
-}
-
-private Map parseCatchAllMessage(String description) {
-	Map resultMap = [:]
-	def cluster = zigbee.parse(description)
-	log.debug cluster
-	if (shouldProcessMessage(cluster)) {
-		switch(cluster.clusterId) {
-			case 0x0001:
-				// 0x07 - configure reporting
-				if (cluster.command != 0x07) {
-					resultMap = getBatteryResult(cluster.data.last())
-				}
-				break
-
-			case 0xFC02:
-				log.debug 'ACCELERATION'
-				break
-
-			case 0x0402:
-				if (cluster.command == 0x07) {
-					if(cluster.data[0] == 0x00) {
-						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
-						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-					}
-					else {
-						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
-					}
-				}
-				else {
-					// temp is last 2 data values. reverse to swap endian
-					String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
-					def value = getTemperature(temp)
-					resultMap = getTemperatureResult(value)
-				}
-				break
-		}
-	}
-
-	return resultMap
-}
-
-private boolean shouldProcessMessage(cluster) {
-	// 0x0B is default response indicating message got through
-	boolean ignoredMessage = cluster.profileId != 0x0104 ||
-			cluster.command == 0x0B ||
-			(cluster.data.size() > 0 && cluster.data.first() == 0x3e)
-	return !ignoredMessage
-}
-
-private List parseReportAttributeMessage(String description) {
-	Map descMap = (description - "read attr - ").split(",").inject([:]) { map, param ->
-		def nameAndValue = param.split(":")
-		map += [(nameAndValue[0].trim()):nameAndValue[1].trim()]
-	}
-
-	List result = []
-	if (descMap.cluster == "0402" && descMap.attrId == "0000") {
-		def value = getTemperature(descMap.value)
-		result << getTemperatureResult(value)
-	}
-	else if (descMap.cluster == "FC02" && descMap.attrId == "0010") {
-		if (descMap.value.size() == 32) {
-			// value will look like 00ae29001403e2290013001629001201
-			// breaking this apart and swapping byte order where appropriate, this breaks down to:
-			//   X (0x0012) = 0x0016
-			//   Y (0x0013) = 0x03E2
-			//   Z (0x0014) = 0x00AE
-			// note that there is a known bug in that the x,y,z attributes are interpreted in the wrong order
-			// this will be fixed in a future update
-			def threeAxisAttributes = descMap.value[0..-9]
-			result << parseAxis(threeAxisAttributes)
-			descMap.value = descMap.value[-2..-1]
-		}
-		result << getAccelerationResult(descMap.value)
-	}
-	else if (descMap.cluster == "FC02" && descMap.attrId == "0012" && descMap.value.size() == 24) {
-		// The size is checked to ensure the attribute report contains X, Y and Z values
-		// If all three axis are not included then the attribute report is ignored
-		result << parseAxis(descMap.value)
-	}
-	else if (descMap.cluster == "0001" && descMap.attrId == "0020") {
-		result << getBatteryResult(Integer.parseInt(descMap.value, 16))
-	}
-
-	return result
-}
-
-private Map parseCustomMessage(String description) {
-	Map resultMap = [:]
-	if (description?.startsWith('temperature: ')) {
-		def value = zigbee.parseHATemperatureValue(description, "temperature: ", getTemperatureScale())
-		resultMap = getTemperatureResult(value)
-	}
-	return resultMap
-}
-
-private Map parseIasMessage(String description) {
-	ZoneStatus zs = zigbee.parseZoneStatus(description)
-	Map resultMap = [:]
-
-	if (garageSensor != "Yes"){
-		resultMap = zs.isAlarm1Set() ? getContactResult('open') : getContactResult('closed')
-	}
-
-	return resultMap
-}
-
-def updated() {
-	log.debug "updated called"
-	log.info "garage value : $garageSensor"
-	if (garageSensor == "Yes") {
-		def descriptionText = "Updating device to garage sensor"
-		if (device.latestValue("status") == "open") {
-			sendEvent(name: 'status', value: 'garage-open', descriptionText: descriptionText, translatable: true)
-		}
-		else if (device.latestValue("status") == "closed") {
-			sendEvent(name: 'status', value: 'garage-closed', descriptionText: descriptionText, translatable: true)
-		}
-	}
-	else {
-		def descriptionText = "Updating device to open/close sensor"
-		if (device.latestValue("status") == "garage-open") {
-			sendEvent(name: 'status', value: 'open', descriptionText: descriptionText, translatable: true)
-		}
-		else if (device.latestValue("status") == "garage-closed") {
-			sendEvent(name: 'status', value: 'closed', descriptionText: descriptionText, translatable: true)
-		}
-	}
-}
-
-def getTemperature(value) {
-	def celsius = Integer.parseInt(value, 16).shortValue() / 100
-	if(getTemperatureScale() == "C"){
-		return Math.round(celsius)
-	} else {
-		return Math.round(celsiusToFahrenheit(celsius))
-	}
-}
-
-private Map getBatteryResult(rawValue) {
-	log.debug 'Battery'
-	def linkText = getLinkText(device)
-
-	def result = [:]
-
-	def volts = rawValue / 10
-
-	if (!(rawValue == 0 || rawValue == 255)) {
-		def minVolts = 2.1
-		def maxVolts = 3.0
-		def pct = (volts - minVolts) / (maxVolts - minVolts)
-		def roundedPct = Math.round(pct * 100)
-		if (roundedPct <= 0)
-			roundedPct = 1
-		result.name = 'battery'
-		result.value = Math.min(100, roundedPct)
-		result.descriptionText = "${linkText} battery was ${result.value}%"
-
-	}
-
-	return result
-}
-
-private Map getTemperatureResult(value) {
-	log.debug "Temperature"
-	if (tempOffset) {
-		def offset = tempOffset as int
-		def v = value as int
-		value = v + offset
-	}
-	def descriptionText = temperatureScale == 'C' ? '{{ device.displayName }} was {{ value }}°C':
-			'{{ device.displayName }} was {{ value }}°F'
-
-	return [
-			name: 'temperature',
-			value: value,
-			descriptionText: descriptionText,
-			translatable: true,
-			unit: temperatureScale
-	]
-}
-
-private Map getContactResult(value) {
-	log.debug "Contact: ${device.displayName} value = ${value}"
-	def descriptionText = value == 'open' ? '{{ device.displayName }} was opened' : '{{ device.displayName }} was closed'
-	sendEvent(name: 'contact', value: value, descriptionText: descriptionText, displayed: false, translatable: true)
-	sendEvent(name: 'status', value: value, descriptionText: descriptionText, translatable: true)
-}
-
-private getAccelerationResult(numValue) {
-	log.debug "Acceleration"
-	def name = "acceleration"
-	def value
-	def descriptionText
-
-	if ( numValue.endsWith("1") ) {
-		value = "active"
-		descriptionText = '{{ device.displayName }} was active'
-	} else {
-		value = "inactive"
-		descriptionText = '{{ device.displayName }} was inactive'
-	}
-
-	def isStateChange = isStateChange(device, name, value)
-	return [
-			name: name,
-			value: value,
-			descriptionText: descriptionText,
-			isStateChange: isStateChange,
-			translatable: true
-	]
-}
-
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-	return zigbee.readAttribute(0x001, 0x0020) // Read the Battery Level
-}
-
-def refresh() {
-	log.debug "Refreshing Values "
-
-	def refreshCmds = []
-
-	if (device.getDataValue("manufacturer") == "SmartThings") {
-		log.debug "Refreshing Values for manufacturer: SmartThings "
-		/* These values of Motion Threshold Multiplier(0x01) and Motion Threshold (0x0276)
-            seem to be giving pretty accurate results for the XYZ co-ordinates for this manufacturer.
-            Separating these out in a separate if-else because I do not want to touch Centralite part
-            as of now.
-        */
-		refreshCmds += zigbee.writeAttribute(0xFC02, 0x0000, 0x20, 0x01, [mfgCode: manufacturerCode])
-		refreshCmds += zigbee.writeAttribute(0xFC02, 0x0002, 0x21, 0x0276, [mfgCode: manufacturerCode])
-	} else {
-		refreshCmds += zigbee.writeAttribute(0xFC02, 0x0000, 0x20, 0x02, [mfgCode: manufacturerCode])
-	}
-
-	//Common refresh commands
-	refreshCmds += zigbee.readAttribute(0x0402, 0x0000) +
-			zigbee.readAttribute(0x0001, 0x0020) +
-			zigbee.readAttribute(0xFC02, 0x0010, [mfgCode: manufacturerCode])
-
-	return refreshCmds + enrollResponse()
-}
-
-def configure() {
-	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
-	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
-
-	log.debug "Configuring Reporting"
-
-	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
-	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	def configCmds = zigbee.batteryConfig() +
-			zigbee.temperatureConfig(30, 300) +
-			zigbee.configureReporting(0xFC02, 0x0010, 0x18, 10, 3600, 0x01, [mfgCode: manufacturerCode]) +
-			zigbee.configureReporting(0xFC02, 0x0012, 0x29, 1, 3600, 0x0001, [mfgCode: manufacturerCode]) +
-			zigbee.configureReporting(0xFC02, 0x0013, 0x29, 1, 3600, 0x0001, [mfgCode: manufacturerCode]) +
-			zigbee.configureReporting(0xFC02, 0x0014, 0x29, 1, 3600, 0x0001, [mfgCode: manufacturerCode])
-
-	return refresh() + configCmds
-}
-
-private getEndpointId() {
-	new BigInteger(device.endpointId, 16).toString()
-}
-
-def enrollResponse() {
-	log.debug "Sending enroll response"
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
-	[
-			//Resending the CIE in case the enroll request is sent before CIE is written
-			"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-			"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
-			//Enroll Response
-			"raw 0x500 {01 23 00 00 00}", "delay 200",
-			"send 0x${device.deviceNetworkId} 1 1", "delay 200"
-	]
-}
-
-private Map parseAxis(String description) {
-	def z = hexToSignedInt(description[0..3])
-	def y = hexToSignedInt(description[10..13])
-	def x = hexToSignedInt(description[20..23])
-	def xyzResults = [x: x, y: y, z: z]
-
-	if (device.getDataValue("manufacturer") == "SmartThings") {
-		// This mapping matches the current behavior of the Device Handler for the Centralite sensors
-		xyzResults.x = z
-		xyzResults.y = y
-		xyzResults.z = -x
-	} else {
-		// The axises reported by the Device Handler differ from the axises reported by the sensor
-		// This may change in the future
-		xyzResults.x = z
-		xyzResults.y = x
-		xyzResults.z = y
-	}
-
-	log.debug "parseAxis -- ${xyzResults}"
-
-	if (garageSensor == "Yes")
-		garageEvent(xyzResults.z)
-
-	getXyzResult(xyzResults, description)
-}
-
-private hexToSignedInt(hexVal) {
-	def unsignedVal = hexToInt(hexVal)
-	unsignedVal > 32767 ? unsignedVal - 65536 : unsignedVal
-}
-
-def garageEvent(zValue) {
-	def absValue = zValue.abs()
-	def contactValue = null
-	def garageValue = null
-	if (absValue>900) {
-		contactValue = 'closed'
-		garageValue = 'garage-closed'
-	}
-	else if (absValue < 100) {
-		contactValue = 'open'
-		garageValue = 'garage-open'
-	}
-	if (contactValue != null){
-		def descriptionText = contactValue == 'open' ? '{{ device.displayName }} was opened' :'{{ device.displayName }} was closed'
-		sendEvent(name: 'contact', value: contactValue, descriptionText: descriptionText, displayed:false, translatable: true)
-		sendEvent(name: 'status', value: garageValue, descriptionText: descriptionText, translatable: true)
-	}
-}
-
-private Map getXyzResult(results, description) {
-	def name = "threeAxis"
-	def value = "${results.x},${results.y},${results.z}"
-	def linkText = getLinkText(device)
-	def descriptionText = "$linkText was $value"
-	def isStateChange = isStateChange(device, name, value)
-
-	[
-			name: name,
-			value: value,
-			unit: null,
-			linkText: linkText,
-			descriptionText: descriptionText,
-			handlerName: name,
-			isStateChange: isStateChange,
-			displayed: false
-	]
-}
-
-private getManufacturerCode() {
-	if (device.getDataValue("manufacturer") == "SmartThings") {
-		return "0x110A"
-	} else {
-		return "0x104E"
-	}
-}
-
-private hexToInt(value) {
-	new BigInteger(value, 16)
-}
-
-private hex(value) {
-	new BigInteger(Math.round(value).toString()).toString(16)
-}
-
-private String swapEndianHex(String hex) {
-	reverseArray(hex.decodeHex()).encodeHex()
-}
-
-private byte[] reverseArray(byte[] array) {
-	int i = 0;
-	int j = array.length - 1;
-	byte tmp;
-	while (j > i) {
-		tmp = array[j];
-		array[j] = array[i];
-		array[i] = tmp;
-		j--;
-		i++;
-	}
-	return array
-}

devicetypes/smartthings/smartsense-open-closed-sensor.src/README.md

@@ -1,6 +1,6 @@
 # Smartsense Open/Closed Sensor
 
-
+Local Execution on V2 Hubs
 
 Works with: 
 
@@ -24,10 +24,11 @@ Works with:
 
 ## Device Health
 
-A Category C2 open/closed sensor with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime. 
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 mins
+SmartSense Open Closed sensor with reporting interval of 5 mins.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+* V1, TV, HubV2 AppEngine < 1.5.1 - __121min__ checkInterval
+* HubV2 AppEngine 1.5.1 - __12min__ checkInterval
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy

@@ -93,7 +93,7 @@ def parse(String description) {
     }
 
 	log.debug "Parse returned $map"
-	def result = map ? createEvent(map) : null
+	def result = map ? createEvent(map) : [:]
 
     if (description?.startsWith('enroll request')) {
     	List cmds = enrollResponse()
@@ -260,9 +260,9 @@ def refresh() {
 }
 
 def configure() {
-	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+	sendEvent(name: "checkInterval", value: 2 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	log.debug "Configuring Reporting, IAS CIE, and Bindings."
 

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/README.md

@@ -1,6 +1,6 @@
 # SmartSense Temp/Humidity Sensor
 
-
+Local Execution on V2 Hubs
 
 Works with: 
 
@@ -24,10 +24,11 @@ Works with:
 
 ## Device Health
 
-A Category C2 SmartSense Temp/Humidity Sensor with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime. 
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 mins
+SmartSense Temp/Humidity Sensor with reporting interval of 5 mins.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+* V1, TV, HubV2 AppEngine < 1.5.1 - __121min__ checkInterval
+* HubV2 AppEngine 1.5.1 - __12min__ checkIntervalr 5 min interval is confirmed
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy

@@ -84,7 +84,7 @@ def parse(String description) {
 	}
 
 	log.debug "Parse returned $map"
-	return map ? createEvent(map) : null
+	return map ? createEvent(map) : [:]
 }
 
 private Map parseCatchAllMessage(String description) {
@@ -264,9 +264,9 @@ def refresh()
 }
 
 def configure() {
-	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+	sendEvent(name: "checkInterval", value: 2 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	log.debug "Configuring Reporting and Bindings."
 	def humidityConfigCmds = [

devicetypes/smartthings/tyco-door-window-sensor.src/README.md

@@ -1,6 +1,6 @@
 # Tyco Door Window Sensor
 
-
+Cloud Execution
 
 Works with: 
 
@@ -23,10 +23,11 @@ Works with:
 
 ## Device Health
 
-Contact sensor with maxReportTime of 5 mins.
+Tyco Door Window Sensor with reporting interval of 5 mins.
 Check-in interval is double the value of maxReportTime for Zigbee device. 
 This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 min
+
+* __12min__ checkInterval
 
 ## Battery Specification
 

devicetypes/smartthings/zigbee-dimmer-power.src/README.md

@@ -1,6 +1,6 @@
 # GE Plug-In/In-Wall Smart Dimmer (ZigBee)
 
-
+Cloud Execution
 
 Works with:
 
@@ -26,11 +26,11 @@ Works with:
 
 ## Device Health
 
-A Zigbee dimmer with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime.
-This gives the device twice the amount of time to respond before it is marked as offline.
-Enrolls with default periodic reporting until newer 5 min interval is confirmed
-It then enrolls the device with updated checkInterval i.e. 12 mins
+A Zigbee Power Dimmer with reporting interval of 5 mins.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+* __12min__ checkInterval
+
 
 ## Troubleshooting
 

devicetypes/smartthings/zigbee-dimmer-power.src/zigbee-dimmer-power.groovy

@@ -114,8 +114,8 @@ def refresh() {
 def configure() {
     log.debug "Configuring Reporting and Bindings."
 
-    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+    // Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 2 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
     refresh()
 }

devicetypes/smartthings/zigbee-dimmer.src/README.md

@@ -1,10 +1,11 @@
-# OSRAM Lightify LED On/Off/Dim
-
+# Zigbee Dimmer
 
+Cloud Execution
 
 Works with: 
 
 * [OSRAM Lightify LED On/Off/Dim](https://shop.smartthings.com/#!/products/osram-led-smart-bulb-on-off-dim)
+* [WeMo LED Bulb](https://support.smartthings.com/hc/en-us/articles/204259040-Belkin-WeMo-LED-Bulb-F7C033-)
 
 ## Table of contents
 
@@ -23,14 +24,16 @@ Works with:
 
 ## Device Health
 
-A Category C1 Zigbee dimmer with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime. 
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 mins
+ZigBee Dimmer with reporting interval of 5 mins.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+* __12min__ checkInterval
+
 
 ## Troubleshooting
 
 If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
 Pairing needs to be tried again by placing the device closer to the hub.
 Other troubleshooting tips are listed as follows:
-* [Troubleshooting:](https://support.smartthings.com/hc/en-us/articles/207191763-OSRAM-LIGHTIFY-LED-Smart-Connected-Light-A19-On-Off-Dim)
+* [OSRAM Lightify LED On/Off/Dim Troubleshooting:](https://support.smartthings.com/hc/en-us/articles/207191763-OSRAM-LIGHTIFY-LED-Smart-Connected-Light-A19-On-Off-Dim)
+* [WeMo LED Bulb Troubleshooting:](https://support.smartthings.com/hc/en-us/articles/204259040-Belkin-WeMo-LED-Bulb-F7C033-)

devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy

@@ -102,9 +102,9 @@ def refresh() {
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+    // Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 2 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig()

devicetypes/smartthings/zigbee-hue-bulb.src/zigbee-hue-bulb.groovy

@@ -1,168 +0,0 @@
-/**
- *  Copyright 2015 SmartThings
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-
-//@Deprecated - Moved to zll-rgbw-bulb
-
-/* Philips Hue (via Zigbee)
-
-Capabilities:
-  Actuator
-  Color Control
-  Configuration
-  Polling
-  Refresh
-  Sensor
-  Switch
-  Switch Level
-
-Custom Commands:
-  setAdjustedColor
-
-*/
-
-metadata {
-	definition (name: "Zigbee Hue Bulb", namespace: "smartthings", author: "SmartThings") {
-		capability "Switch Level"
-		capability "Actuator"
-		capability "Color Control"
-		capability "Switch"
-		capability "Configuration"
-		capability "Polling"
-		capability "Refresh"
-		capability "Sensor"
-
-		command "setAdjustedColor"
-
-		//fingerprint profileId: "C05E", inClusters: "0000,0003,0004,0005,0006,0008,0300,1000", outClusters: "0019"
-	}
-
-	// UI tile definitions
-	tiles(scale: 2) {
-		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
-			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-				attributeState "on", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
-				attributeState "off", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
-				attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
-				attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
-			}
-			tileAttribute ("device.level", key: "SLIDER_CONTROL") {
-				attributeState "level", action:"switch level.setLevel"
-			}
-			tileAttribute ("device.color", key: "COLOR_CONTROL") {
-				attributeState "color", action:"color control.setColor"
-			}
-		}
-		controlTile("colorTempSliderControl", "device.colorTemperature", "slider", width: 4, height: 2, inactiveLabel: false, range:"(2700..6500)") {
-			state "colorTemperature", action:"color temperature.setColorTemperature"
-		}
-		valueTile("colorTemp", "device.colorTemperature", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-			state "colorTemperature", label: '${currentValue} K'
-		}
-		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
-			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-		}
-
-		main(["switch"])
-		details(["switch", "colorTempSliderControl", "colorTemp", "refresh"])
-	}
-}
-
-//Globals
-private getATTRIBUTE_HUE() { 0x0000 }
-private getATTRIBUTE_SATURATION() { 0x0001 }
-private getHUE_COMMAND() { 0x00 }
-private getSATURATION_COMMAND() { 0x03 }
-private getCOLOR_CONTROL_CLUSTER() { 0x0300 }
-private getATTRIBUTE_COLOR_TEMPERATURE() { 0x0007 }
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-	log.debug "description is $description"
-
-	def finalResult = zigbee.getEvent(description)
-	if (finalResult) {
-		log.debug finalResult
-		sendEvent(finalResult)
-	}
-	else {
-		def zigbeeMap = zigbee.parseDescriptionAsMap(description)
-		log.trace "zigbeeMap : $zigbeeMap"
-
-		if (zigbeeMap?.clusterInt == COLOR_CONTROL_CLUSTER) {
-			if(zigbeeMap.attrInt == ATTRIBUTE_HUE){  //Hue Attribute
-				def hueValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 360)
-				sendEvent(name: "hue", value: hueValue, displayed:false)
-			}
-			else if(zigbeeMap.attrInt == ATTRIBUTE_SATURATION){ //Saturation Attribute
-				def saturationValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
-				sendEvent(name: "saturation", value: saturationValue, displayed:false)
-			}
-		}
-		else {
-			log.info "DID NOT PARSE MESSAGE for description : $description"
-		}
-	}
-}
-
-def on() {
-	zigbee.on() + ["delay 1500"] + zigbee.onOffRefresh()
-}
-
-def off() {
-	zigbee.off() + ["delay 1500"] + zigbee.onOffRefresh()
-}
-
-def refresh() {
-	refreshAttributes() + configureAttributes()
-}
-
-def poll() {
-	refreshAttributes()
-}
-
-def configure() {
-	log.debug "Configuring Reporting and Bindings."
-	configureAttributes() + refreshAttributes()
-}
-
-def configureAttributes() {
-	zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
-}
-
-def refreshAttributes() {
-	zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
-}
-
-def setColorTemperature(value) {
-	zigbee.setColorTemperature(value) + ["delay 1500"] + zigbee.colorTemperatureRefresh()
-}
-
-def setLevel(value) {
-	zigbee.setLevel(value) + ["delay 1500"] + zigbee.levelRefresh()         //adding refresh because of ZLL bulb not conforming to send-me-a-report
-}
-
-def setColor(value){
-	log.trace "setColor($value)"
-	zigbee.on() + setHue(value.hue) + ["delay 300"] + setSaturation(value.saturation) + ["delay 2000"] + refreshAttributes()
-}
-
-def setHue(value) {
-	def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-	zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE)       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
-}
-
-def setSaturation(value) {
-	def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-	zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)      //payload-> sat value, transition time
-}

devicetypes/smartthings/zigbee-rgbw-bulb.src/README.md

@@ -1,6 +1,6 @@
 # OSRAM LIGHTIFY LED RGBW Bulb
 
-
+Cloud Execution
 
 Works with: 
 
@@ -27,11 +27,10 @@ Works with:
 
 ## Device Health
 
-A Category C6 OSRAM LIGHTIFY LED RGBW Bulb with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime. 
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 mins
+OSRAM LIGHTIFY LED RGBW Bulb with reporting interval of 5 mins.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
 
+* __12min__ checkInterval
 
 ## Troubleshooting
 

devicetypes/smartthings/zigbee-rgbw-bulb.src/zigbee-rgbw-bulb.groovy

@@ -143,9 +143,9 @@ def refresh() {
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+    // Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 2 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     refresh()

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/README.md

@@ -1,10 +1,11 @@
-# OSRAM Lightify Tunable 60 White
-
+# ZigBee White Color Temperature Bulb
 
+Cloud Execution
 
 Works with: 
 
 * [OSRAM Lightify Tunable 60 White](http://www.osram.com/osram_com/tools-and-services/tools/lightify---smart-connected-light/lightify-for-home---what-is-light-to-you/lightify-products/lightify-classic-a60-tunable-white/index.jsp)
+* [OSRAM LIGHTIFY RT5/6 Tunable White](https://www.smartthings.com/works-with-smartthings/light-bulbs/osram-lightify-rt56-tunable-white)
 
 ## Table of contents
 
@@ -24,14 +25,15 @@ Works with:
 
 ## Device Health
 
-A Category C1 OSRAM Lightify Tunable 60 White with maxReportTime of 5 mins.
-Check-in interval is double the value of maxReportTime. 
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 12 mins
+Zigbee Bulb with reporting interval of 5 mins.
+SmartThings platform will ping the device after `checkInterval` seconds of inactivity in last attempt to reach the device before marking it `OFFLINE` 
+
+*__12min__ checkInterval
 
 ## Troubleshooting
 
 If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
 Pairing needs to be tried again by placing the device closer to the hub.
 Other troubleshooting tips are listed as follows:
-* [Troubleshooting:](https://support.smartthings.com/hc/en-us/articles/204576454-OSRAM-LIGHTIFY-Tunable-White-60-Bulb)
+* [OSRAM Lightify Tunable 60 White Troubleshooting](https://support.smartthings.com/hc/en-us/articles/204576454-OSRAM-LIGHTIFY-Tunable-White-60-Bulb)
+* [OSRAM LIGHTIFY RT5/6 Tunable White Troubleshooting](https://support.smartthings.com/hc/en-us/articles/214191863-How-to-connect-OSRAM-LIGHTIFY-Bulbs)

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/zigbee-white-color-temperature-bulb.groovy

@@ -126,9 +126,9 @@ def refresh() {
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+    // Device-Watch allows 2 check-in misses from device + ping (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 2 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     refresh()

devicetypes/smartthings/zwave-dimmer-switch-generic.src/README.md

@@ -1,10 +1,11 @@
-# Z-wave Dimmer
-
+# Z-wave Dimmer Switch Generic
 
+Cloud Execution
 
 Works with: 
 
-* [Leviton Plug-in Lamp Dimmer Module (DZPD3-1LW)](http://www.leviton.com/OA_HTML/ProductDetail.jsp?partnumber=DZPD3-1LW)
+* [Leviton Plug-in Lamp Dimmer Module (DZPD3-1LW)](https://www.smartthings.com/works-with-smartthings/outlets/leviton-plug-in-lamp-dimmer-module)
+* [Leviton Universal Dimmer (DZMX1-LZ)](https://www.smartthings.com/works-with-smartthings/switches-and-dimmers/leviton-universal-dimmer)
 
 ## Table of contents
 
@@ -24,16 +25,19 @@ Works with:
 
 ## Device Health
 
-A Category C5 Leviton Plug-in Lamp Dimmer Module (DZPA1-1LW) (Z-Wave) polled by the hub.
+Leviton Plug-in Lamp Dimmer Module (DZPA1-1LW) (Z-wave) and Leviton Universal Dimmer (DZMX1-LZ) (Z-Wave) are polled by the hub.
 As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
 Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
 Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
 the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
 it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
 
+* __32min__ checkInterval
+
 ## Troubleshooting
 
 If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
 Pairing needs to be tried again by placing the device closer to the hub.
 Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
-* [Leviton Plug-in Lamp Dimmer Module (DZPD3-1LW) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/206171053-How-to-connect-Leviton-Z-Wave-devices)
+* [Leviton Plug-in Lamp Dimmer Module (DZPD3-1LW) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/206171053-How-to-connect-Leviton-Z-Wave-devices)
+* [Leviton Universal Dimmer (DZMX1-LZ) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/206171053-How-to-connect-Leviton-Z-Wave-devices)

devicetypes/smartthings/zwave-dimmer-switch-generic.src/zwave-dimmer-switch-generic.groovy

@@ -23,6 +23,7 @@ metadata {
 
 		fingerprint inClusters: "0x26", deviceJoinName: "Z-Wave Dimmer"
 		fingerprint mfr:"001D", prod:"1902", deviceJoinName: "Z-Wave Dimmer"
+		fingerprint mfr:"001D", prod:"1B03", model:"0334", deviceJoinName: "Leviton Universal Dimmer"
 	}
 
 	simulator {

devicetypes/smartthings/zwave-switch-generic.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-switch-generic.src/README.md

@@ -0,0 +1,45 @@
+# Z-wave Switch
+
+Cloud Execution
+
+Works with: 
+
+* [Leviton Appliance Module (DZPA1-1LW)](https://www.smartthings.com/works-with-smartthings/outlets/leviton-appliance-module)
+* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave)](https://www.smartthings.com/works-with-smartthings/outlets/ge-plug-in-outdoor-smart-switch)
+* [Leviton Outlet (DZR15-1LZ)](https://www.smartthings.com/works-with-smartthings/outlets/leviton-outlet)
+* [Leviton Switch (DZS15-1LZ)](https://www.smartthings.com/works-with-smartthings/switches-and-dimmers/leviton-switch)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Health Check** - indicates ability to get device health notifications
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+
+## Device Health
+
+Leviton Appliance Module (DZPA1-1LW), GE Plug-In Outdoor Smart Switch (GE 12720), Leviton Outlet (DZR15-1LZ) and Leviton Switch (DZS15-1LZ) (Z-Wave) are polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+* __32min__ checkInterval
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Leviton Appliance Module (DZPA1-1LW) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/206171053-How-to-connect-Leviton-Z-Wave-devices)
+* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)
+* [Leviton Outlet (DZR15-1LZ) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/206171053-How-to-connect-Leviton-Z-Wave-devices)
+* [Leviton Switch (DZS15-1LZ) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/206171053-How-to-connect-Leviton-Z-Wave-devices)

devicetypes/smartthings/zwave-switch-generic.src/zwave-switch-generic.groovy

@@ -14,12 +14,17 @@
 metadata {
 	definition (name: "Z-Wave Switch Generic", namespace: "smartthings", author: "SmartThings") {
 		capability "Actuator"
+		capability "Health Check"
  		capability "Switch"
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
 
 		fingerprint inClusters: "0x25", deviceJoinName: "Z-Wave Switch"
+		fingerprint mfr:"001D", prod:"1A02", model:"0334", deviceJoinName: "Leviton Appliance Module"
+		fingerprint mfr:"0063", prod:"4F50", model:"3031", deviceJoinName: "GE Plug-in Outdoor Switch"
+		fingerprint mfr:"001D", prod:"1D04", model:"0334", deviceJoinName: "Leviton Outlet"
+		fingerprint mfr:"001D", prod:"1C02", model:"0334", deviceJoinName: "Leviton Switch"
 	}
 
 	// simulator metadata
@@ -50,6 +55,11 @@ metadata {
 	}
 }
 
+def updated(){
+// Device-Watch simply pings if no device events received for checkInterval duration of 32min = 2 * 15min + 2min lag time
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description) {
 	def result = null
 	def cmd = zwave.parse(description, [0x20: 1, 0x70: 1])
@@ -126,6 +136,13 @@ def poll() {
 	])
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),

devicetypes/smartthings/zwave-switch.src/README.md

@@ -1,5 +1,6 @@
 # Z-Wave Switch
 
+Local Execution on V2 Hubs
 
 Works with: 
 
@@ -34,6 +35,7 @@ Not to mention after going OFFLINE when the device is plugged back in, it might
 the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
 it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
 
+* __32min__ checkInterval
 
 ## Troubleshooting
 

smartapps/smartthings/ecobee-connect.src/ecobee-connect.groovy

@@ -842,6 +842,7 @@ private void storeThermostatData(thermostats) {
             minCoolingSetpoint: (stat.settings.coolRangeLow / 10),
             maxCoolingSetpoint: (stat.settings.coolRangeHigh / 10),
             autoMode: stat.settings.autoHeatCoolFeatureEnabled,
+            deviceAlive: stat.runtime.connected == true ? "true" : "false",
             auxHeatMode: (stat.settings.hasHeatPump) && (stat.settings.hasForcedAir || stat.settings.hasElectric || stat.settings.hasBoiler),
             temperature: (stat.runtime.actualTemperature / 10),
             heatingSetpoint: stat.runtime.desiredHeat / 10,

smartapps/smartthings/logitech-harmony-connect.src/logitech-harmony-connect.groovy

@@ -24,6 +24,12 @@
  *  switches             | switch            | on, off                     | on, off
  *  motionSensors        | motion            |                             | active, inactive
  *  contactSensors       | contact           |                             | open, closed
+ *  thermostat           | thermostat        | setHeatingSetpoint,         | temperature, heatingSetpoint
+ *                       |                   | setCoolingSetpoint(number)  | coolingSetpoint, thermostatSetpoint
+ *                       |                   | off, heat, emergencyHeat    | thermostatMode — ["emergency heat", "auto", "cool", "off", "heat"]
+ *                       |                   | cool, setThermostatMode     | thermostatFanMode — ["auto", "on", "circulate"]
+ *                       |                   | fanOn, fanAuto, fanCirculate| thermostatOperatingState — ["cooling", "heating", "pending heat",
+ *                       |                   | setThermostatFanMode, auto  | "fan only", "vent economizer", "pending cool", "idle"]
  *  presenceSensors      | presence          |                             | present, 'not present'
  *  temperatureSensors   | temperature       |                             | <numeric, F or C according to unit>
  *  accelerationSensors  | acceleration      |                             | active, inactive
@@ -58,6 +64,7 @@ preferences(oauthPage: "deviceAuthorization") {
 			input "switches", "capability.switch", title: "Which Switches?", multiple: true, required: false
 			input "motionSensors", "capability.motionSensor", title: "Which Motion Sensors?", multiple: true, required: false
 			input "contactSensors", "capability.contactSensor", title: "Which Contact Sensors?", multiple: true, required: false
+      input "thermostats", "capability.thermostat", title: "Which Thermostats?", multiple: true, required: false
 			input "presenceSensors", "capability.presenceSensor", title: "Which Presence Sensors?", multiple: true, required: false
 			input "temperatureSensors", "capability.temperatureMeasurement", title: "Which Temperature Sensors?", multiple: true, required: false
 			input "accelerationSensors", "capability.accelerationSensor", title: "Which Vibration Sensors?", multiple: true, required: false
@@ -936,7 +943,7 @@ def deleteHarmony() {
 }
 
 private getAllDevices() {
-	([] + switches + motionSensors + contactSensors + presenceSensors + temperatureSensors + accelerationSensors + waterSensors + lightSensors + humiditySensors + alarms + locks)?.findAll()?.unique { it.id }
+	([] + switches + motionSensors + contactSensors + thermostats + presenceSensors + temperatureSensors + accelerationSensors + waterSensors + lightSensors + humiditySensors + alarms + locks)?.findAll()?.unique { it.id }
 }
 
 private deviceItem(device) {