Revert "[CHF-404] [CHF-422] Health check for Leviton DZPA1 Plug-in Appliance Module and GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave)"

DVCSMP-2155 ZigBee switch power DH health check

devicetypes/smartthings/zigbee-switch-power.src/zigbee-switch-power.groovy

@@ -20,6 +20,7 @@ metadata {
         capability "Power Meter"
         capability "Sensor"
         capability "Switch"
+        capability "Health Check"
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0B04"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0702"
@@ -77,10 +78,26 @@ def on() {
 }
 
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
+    Integer reportIntervalMinutes = 5
+    zigbee.onOffRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig(0,reportIntervalMinutes * 60) + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
 }
 
 def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    refresh()
+    log.debug "in configure()"
+    configureHealthCheck()
+}
+
+def configureHealthCheck() {
+    Integer hcIntervalMinutes = 12
+    refresh()
+    sendEvent(name: "checkInterval", value: hcIntervalMinutes * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+}
+
+def updated() {
+    log.debug "in updated()"
+    configureHealthCheck()
+}
+
+def ping() {
+    return zigbee.onOffRefresh()
 }

devicetypes/smartthings/zwave-switch-generic.src/.st-ignore

@@ -1,2 +0,0 @@
-.st-ignore
-README.md

devicetypes/smartthings/zwave-switch-generic.src/README.md

@@ -1,39 +0,0 @@
-# Z-wave Switch
-
-
-
-Works with: 
-
-* [Leviton Appliance Module (DZPA1-1LW)](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
-* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave)](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)
-
-## Table of contents
-
-* [Capabilities](#capabilities)
-* [Health](#device-health)
-
-## Capabilities
-
-* **Actuator** - represents that a Device has commands
-* **Health Check** - indicates ability to get device health notifications
-* **Switch** - can detect state (possible values: on/off)
-* **Polling** - represents that poll() can be implemented for the device
-* **Refresh** - _refresh()_ command for status updates
-* **Sensor** - detects sensor events
-
-## Device Health
-
-A Category C5 Leviton Appliance Module (DZPA1-1LW) and GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) polled by the hub.
-As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
-Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
-Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
-the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
-it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
-
-## Troubleshooting
-
-If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
-Pairing needs to be tried again by placing the device closer to the hub.
-Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
-* [Leviton Appliance Module (DZPA1-1LW) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
-* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)

devicetypes/smartthings/zwave-switch-generic.src/zwave-switch-generic.groovy

@@ -14,15 +14,12 @@
 metadata {
 	definition (name: "Z-Wave Switch Generic", namespace: "smartthings", author: "SmartThings") {
 		capability "Actuator"
-		capability "Health Check"
  		capability "Switch"
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
 
 		fingerprint inClusters: "0x25", deviceJoinName: "Z-Wave Switch"
-		fingerprint mfr:"001D", prod:"1A02", deviceJoinName: "Z-Wave Switch"
-		fingerprint mfr:"0063", prod:"4F50", deviceJoinName: "Z-Wave Switch"
 	}
 
 	// simulator metadata
@@ -53,11 +50,6 @@ metadata {
 	}
 }
 
-def updated(){
-// Device-Watch simply pings if no device events received for checkInterval duration of 32min = 2 * 15min + 2min lag time
-	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
-}
-
 def parse(String description) {
 	def result = null
 	def cmd = zwave.parse(description, [0x20: 1, 0x70: 1])
@@ -134,13 +126,6 @@ def poll() {
 	])
 }
 
-/**
- * PING is used by Device-Watch in attempt to reach the Device
- * */
-def ping() {
-	refresh()
-}
-
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),