MSA-692: Allows control of Aeon Micro Motor Controller, a Z-Wave device, both from the mobile app tiles, and SmartApps. The device type maps the three hardware states into ST: Up, Down, Stop, and provides commands with the same names. When used with motor shades, generally the motor has an adjustable automatic stop at the full height or extension of the shade, so the physical switch would just select Up, and that was that. The motor stopped despite the switch. The physical switch would typically also have an Off position. The micro motor controller does as well, hence the stop() command. Below is the ReadMe for this device type:

To use this device type in SmartApps, use "capability.doorControl" in Preferences to select the controller.  
Then you can reference the state of the device with device.currentValue("motor") or device.currentMotor.  
The device can be in one of three states: up, down, stop, e.g. if(device.currentMotor == "up") {...}  
There are three commands available: up(), down(), stop(), e.g. device.up()

After you include the Aeon device into ST, edit its device type in the IDE to be "Aeon Motor Controller"

Down turns on motor M1, and Up turns on motor M2.

devicetypes/bravenel/aeon-motor-controller.src/aeon-motor-controller.groovy

@@ -0,0 +1,145 @@
+/**
+ *  Aeon Motor Controller
+ *
+ *  Copyright 2015 Bruce Ravenel
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+metadata {
+	definition (name: "Aeon Motor Controller", namespace: "bravenel", author: "Bruce Ravenel") {
+		capability "Refresh"
+		capability "Actuator"
+        capability "doorControl"
+        capability "Switch"
+
+        command "up"
+        command "down"
+        command "stop"
+
+//		fingerprint inClusters: "0x26,0x32"
+	}
+
+	simulator {
+        status "up":   "command: 2604, payload: FF"
+        status "down": "command: 2604, payload: 00"
+        status "stop": "command: 2605, payload: FE"
+
+		["FF", "FE", "00"].each { val ->
+			reply "2001$val,delay 100,2602": "command: 2603, payload: $val"
+		}
+	}
+
+	tiles {
+		standardTile("motor", "device.motor", width: 2, height: 2) {
+			state("stopUp", label:'stop', icon:"st.doors.garage.garage-open", action: 'down', backgroundColor:"#79b821")
+			state("stopDn", label:'stop', icon:"st.doors.garage.garage-closed", action: 'up', backgroundColor:"#79b821")
+			state("up", label:'up', icon:"st.doors.garage.garage-opening", action:'stop', backgroundColor:"#ffe71e")
+			state("down", label:'down', icon:"st.doors.garage.garage-closing", action:'stop', backgroundColor:"#ffe71e")
+		}
+		valueTile("energy", "device.energy", decoration: "flat") {
+			state "default", label:' '
+		}
+		standardTile("refresh", "device.switch", inactiveLabel: false, decoration: "flat") {
+			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
+		}
+        standardTile("stop", "device.switch") {
+        	state "default", label:"", action: "stop", icon:"http://cdn.device-icons.smartthings.com/sonos/stop-btn@2x.png"
+        }
+        standardTile("up", "device.switch") {
+        	state "default", label: "Up", action: "up", icon:"http://cdn.device-icons.smartthings.com/thermostat/thermostat-up@2x.png"
+        }
+        standardTile("down", "device.switch") {
+        	state "default", label: "Down", action: "down", icon:"http://cdn.device-icons.smartthings.com/thermostat/thermostat-down@2x.png"
+        }
+	}
+	main(["motor"])
+	details(["motor",  "refresh", "energy", "up", "down", "stop",])
+}
+
+// parse events into attributes
+def parse(String description) {
+	def result = []
+	def cmd = zwave.parse(description, [0x20: 1, 0x26: 3])
+	if (cmd) {
+		result = zwaveEvent(cmd)
+		log.debug("'$description' parsed to $result")
+	} else {
+		log.debug("Couldn't zwave.parse '$description'")
+	}
+	result
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.basicv1.BasicReport cmd) {
+	motorEvents(cmd)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.basicv1.BasicSet cmd) {
+	motorEvents(cmd)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.switchmultilevelv3.SwitchMultilevelReport cmd) {
+	motorEvents(cmd)
+}
+
+def motorEvents(physicalgraph.zwave.Command cmd) {
+	def result = []
+    def switchEvent = []
+    if(cmd.value == 0) {switchEvent = createEvent(name: "motor", value: "down", descriptionText: text)}
+    else if(cmd.value == 254) {
+    	def stopVal = state.up ? "stopUp" : "stopDn"
+    	switchEvent = createEvent(name: "motor", value: stopVal, descriptionText: text)
+    }
+    else if(cmd.value == 255) {switchEvent = createEvent(name: "motor", value: "up", descriptionText: text)}
+	result << switchEvent
+}
+
+def refresh() {
+	zwave.switchMultilevelV1.switchMultilevelGet().format()
+}
+
+def up() {
+	state.up = true
+	delayBetween([
+    	zwave.basicV1.basicSet(value: 0xFF).format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}
+
+def down() {
+	state.up = false
+	delayBetween([
+    	zwave.basicV1.basicSet(value: 0x00).format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}
+
+def stop() {
+	delayBetween([
+    	zwave.switchMultilevelV1.switchMultilevelStopLevelChange().format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}
+
+def on() {
+	state.up = true
+	delayBetween([
+    	zwave.basicV1.basicSet(value: 0xFF).format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}
+
+def off() {
+	state.up = false
+	delayBetween([
+    	zwave.basicV1.basicSet(value: 0x00).format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}

devicetypes/smartthings/centralite-dimmer.src/centralite-dimmer.groovy

@@ -15,7 +15,6 @@
  *	Author: SmartThings
  *	Date: 2013-12-04
  */
-//DEPRECATED - Using the generic DTH for this device. Users need to be moved before deleting this DTH
 metadata {
 	definition (name: "CentraLite Dimmer", namespace: "smartthings", author: "SmartThings") {
 		capability "Switch Level"
@@ -26,6 +25,7 @@ metadata {
 		capability "Refresh"
 		capability "Sensor"
 
+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0B04,0B05", outClusters: "0019"
 	}
 
 	// simulator metadata

devicetypes/smartthings/harmony-activity.src/harmony-activity.groovy

@@ -14,7 +14,7 @@
  *
  */
 metadata {
-        definition (name: "Harmony Activity", namespace: "smartthings", author: "Juan Risso") {
+        definition (name: "Logitech Harmony Activity", namespace: "smartthings", author: "Juan Risso") {
         capability "Switch"
         capability "Actuator"
 		capability "Refresh"

devicetypes/smartthings/smartsense-garage-door-multi.src/smartsense-garage-door-multi.groovy

@@ -79,8 +79,8 @@ metadata {
 	}
     
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}    
 }
 

devicetypes/smartthings/smartsense-garage-door-sensor-button.src/smartsense-garage-door-sensor-button.groovy

@@ -88,8 +88,8 @@ metadata {
 	}
 
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}
 }
 

devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy

@@ -43,8 +43,8 @@ metadata {
 				])
 		}
 		section {
-			input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-			input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+			input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+			input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 		}
 	}
  

devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy

@@ -45,8 +45,8 @@ metadata {
 				])
 		}
 		section {
-			input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-			input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+			input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+			input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 		}
 	}
 

devicetypes/smartthings/smartsense-motion-temp-sensor.src/smartsense-motion-temp-sensor.groovy

@@ -37,8 +37,8 @@ metadata {
 	}
 
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}
 
 	tiles(scale: 2) {

devicetypes/smartthings/smartsense-multi-sensor.src/smartsense-multi-sensor.groovy

@@ -61,8 +61,8 @@
 				])
 		}
 		section {
- 			input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
- 			input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+ 			input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+ 			input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
  		}
 		section {
  			input("garageSensor", "enum", title: "Do you want to use this sensor on a garage door?", options: ["Yes", "No"], defaultValue: "No", required: false, displayDuringSetup: false)

devicetypes/smartthings/smartsense-multi.src/smartsense-multi.groovy

@@ -43,8 +43,8 @@ metadata {
 	}
 
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}
 
 	tiles(scale: 2) {

devicetypes/smartthings/smartsense-open-closed-accelerometer-sensor.src/smartsense-open-closed-accelerometer-sensor.groovy

@@ -32,8 +32,8 @@
  	}
 
  	preferences {
- 		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
- 		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+ 		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+ 		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
  	}
 
 	tiles(scale: 2) {

devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy

@@ -34,8 +34,8 @@ metadata {
 	}
 
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}
  
 	tiles(scale: 2) {

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy

@@ -33,8 +33,8 @@ metadata {
 	}
 
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}
 
 	tiles(scale: 2) {

devicetypes/smartthings/smartsense-virtual-open-closed.src/smartsense-virtual-open-closed.groovy

@@ -45,8 +45,8 @@ metadata {
 	}
     
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}    
 
 	tiles {

devicetypes/smartthings/tyco-door-window-sensor.src/tyco-door-window-sensor.groovy

@@ -33,8 +33,8 @@ metadata {
 	}
 
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}
  
 	tiles {

devicetypes/smartthings/zigbee-dimmer-power.src/zigbee-dimmer-power.groovy

@@ -25,8 +25,8 @@ metadata {
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B04"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "Z01-CIA19NAE26", deviceJoinName: "Sengled Element touch"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "000A, 0019", manufacturer: "Jasco Products", model: "45852", deviceJoinName: "GE Zigbee Plug-In Dimmer"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "000A, 0019", manufacturer: "Jasco Products", model: "45857", deviceJoinName: "GE Zigbee In-Wall Dimmer"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0B05,0702", outClusters: "000A,0019", manufacturer: "Jasco Products", model: "45852", deviceJoinName: "GE Zigbee Plug-In Dimmer"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0B05,0702", outClusters: "000A,0019", manufacturer: "Jasco Products", model: "45857", deviceJoinName: "GE Zigbee In-Wall Dimmer"
     }
 
     tiles(scale: 2) {

devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy

@@ -17,14 +17,15 @@ metadata {
         capability "Actuator"
         capability "Configuration"
         capability "Refresh"
+        capability "Sensor"
         capability "Switch"
         capability "Switch Level"
 
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 ON/OFF/DIM", deviceJoinName: "OSRAM LIGHTIFY LED Smart Connected Light"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, FF00", outClusters: "0019", manufacturer: "MRVL", model: "MZ100", deviceJoinName: "Wemo Bulb"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B05", outClusters: "0019", manufacturer: "OSRAM SYLVANIA", model: "iQBR30", deviceJoinName: "Sylvania Ultra iQ"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,FF00", outClusters: "0019", manufacturer: "MRVL", model: "MZ100", deviceJoinName: "Wemo Bulb"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0B05", outClusters: "0019", manufacturer: "OSRAM SYLVANIA", model: "iQBR30", deviceJoinName: "Sylvania Ultra iQ"
     }
 
     tiles(scale: 2) {

devicetypes/smartthings/zigbee-switch-power.src/zigbee-switch-power.groovy

@@ -23,8 +23,8 @@ metadata {
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0B04"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0702"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0702, 0B05", outClusters: "0003, 000A, 0019", manufacturer: "Jasco Products", model: "45853", deviceJoinName: "GE ZigBee Plug-In Switch"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0702, 0B05", outClusters: "000A, 0019", manufacturer: "Jasco Products", model: "45856", deviceJoinName: "GE ZigBee In-Wall Switch"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0B05,0702", outClusters: "0003, 000A,0019", manufacturer: "Jasco Products", model: "45853", deviceJoinName: "GE ZigBee Plug-In Switch"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0B05,0702", outClusters: "000A,0019", manufacturer: "Jasco Products", model: "45856", deviceJoinName: "GE ZigBee In-Wall Switch"
     }
 
     tiles(scale: 2) {

devicetypes/smartthings/zigbee-switch.src/zigbee-switch.groovy

@@ -17,6 +17,7 @@ metadata {
         capability "Actuator"
         capability "Configuration"
         capability "Refresh"
+        capability "Sensor"
         capability "Switch"
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006"

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/zigbee-white-color-temperature-bulb.groovy

@@ -23,18 +23,18 @@ metadata {
         capability "Color Temperature"
         capability "Configuration"
         capability "Refresh"
+        capability "Sensor"
         capability "Switch"
         capability "Switch Level"
 
         attribute "colorName", "string"
         command "setGenericName"
 
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300", outClusters: "0019"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04", outClusters: "0019"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY BR Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Flood BR30 Tunable White"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY RT Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Recessed Kit RT 5/6 Tunable White"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Classic A60 TW", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04", outClusters: "0019"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY BR Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Flood BR30 Tunable White"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY RT Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Recessed Kit RT 5/6 Tunable White"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Classic A60 TW", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
     }
 
     // UI tile definitions

devicetypes/smartthings/zwave-lock.src/zwave-lock.groovy

@@ -66,20 +66,9 @@ metadata {
 import physicalgraph.zwave.commands.doorlockv1.*
 import physicalgraph.zwave.commands.usercodev1.*
 
-def updated() {
-	try {
-		if (!state.init) {
-			state.init = true
-			response(secureSequence([zwave.doorLockV1.doorLockOperationGet(), zwave.batteryV1.batteryGet()]))
-		}
-	} catch (e) {
-		log.warn "updated() threw $e"
-	}
-}
-
 def parse(String description) {
 	def result = null
-	if (description.startsWith("Err 106")) {
+	if (description.startsWith("Err")) {
 		if (state.sec) {
 			result = createEvent(descriptionText:description, displayed:false)
 		} else {
@@ -91,8 +80,6 @@ def parse(String description) {
 				displayed: true,
 			)
 		}
-	} else if (description == "updated") {
-		return null
 	} else {
 		def cmd = zwave.parse(description, [ 0x98: 1, 0x72: 2, 0x85: 2, 0x86: 1 ])
 		if (cmd) {
@@ -299,7 +286,7 @@ def zwaveEvent(physicalgraph.zwave.commands.alarmv2.AlarmReport cmd) {
 			}
 			break
 		case 167:
-			if (!state.lastbatt || now() - state.lastbatt > 12*60*60*1000) {
+			if (!state.lastbatt || (new Date().time) - state.lastbatt > 12*60*60*1000) {
 				map = [ descriptionText: "$device.displayName: battery low", isStateChange: true ]
 				result << response(secure(zwave.batteryV1.batteryGet()))
 			} else {
@@ -444,7 +431,7 @@ def zwaveEvent(physicalgraph.zwave.commands.batteryv1.BatteryReport cmd) {
 	} else {
 		map.value = cmd.batteryLevel
 	}
-	state.lastbatt = now()
+	state.lastbatt = new Date().time
 	createEvent(map)
 }
 
@@ -512,14 +499,15 @@ def refresh() {
 		cmds << "delay 4200"
 		cmds << zwave.associationV1.associationGet(groupingIdentifier:2).format()  // old Schlage locks use group 2 and don't secure the Association CC
 		cmds << secure(zwave.associationV1.associationGet(groupingIdentifier:1))
-		state.associationQuery = now()
-	} else if (secondsPast(state.associationQuery, 9)) {
+		state.associationQuery = new Date().time
+	} else if (new Date().time - state.associationQuery.toLong() > 9000) {
+		log.debug "setting association"
 		cmds << "delay 6000"
 		cmds << zwave.associationV1.associationSet(groupingIdentifier:2, nodeId:zwaveHubNodeId).format()
 		cmds << secure(zwave.associationV1.associationSet(groupingIdentifier:1, nodeId:zwaveHubNodeId))
 		cmds << zwave.associationV1.associationGet(groupingIdentifier:2).format()
 		cmds << secure(zwave.associationV1.associationGet(groupingIdentifier:1))
-		state.associationQuery = now()
+		state.associationQuery = new Date().time
 	}
 	log.debug "refresh sending ${cmds.inspect()}"
 	cmds
@@ -527,22 +515,55 @@ def refresh() {
 
 def poll() {
 	def cmds = []
-	// Only check lock state if it changed recently or we haven't had an update in an hour
-	def latest = device.currentState("lock")?.date?.time
-	if (!latest || !secondsPast(latest, 6 * 60) || secondsPast(state.lastPoll, 55 * 60)) {
-		cmds << secure(zwave.doorLockV1.doorLockOperationGet())
-		state.lastPoll = now()
-	} else if (!state.lastbatt || now() - state.lastbatt > 53*60*60*1000) {
-		cmds << secure(zwave.batteryV1.batteryGet())
-		state.lastbatt = now()  //inside-214
-	}
-	if (cmds) {
-		log.debug "poll is sending ${cmds.inspect()}"
-		cmds
+	if (state.assoc != zwaveHubNodeId && secondsPast(state.associationQuery, 19 * 60)) {
+		log.debug "setting association"
+		cmds << zwave.associationV1.associationSet(groupingIdentifier:2, nodeId:zwaveHubNodeId).format()
+		cmds << secure(zwave.associationV1.associationSet(groupingIdentifier:1, nodeId:zwaveHubNodeId))
+		cmds << zwave.associationV1.associationGet(groupingIdentifier:2).format()
+		cmds << "delay 6000"
+		cmds << secure(zwave.associationV1.associationGet(groupingIdentifier:1))
+		cmds << "delay 6000"
+		state.associationQuery = new Date().time
 	} else {
-		// workaround to keep polling from stopping due to lack of activity
-		sendEvent(descriptionText: "skipping poll", isStateChange: true, displayed: false)
-		null
+		// Only check lock state if it changed recently or we haven't had an update in an hour
+		def latest = device.currentState("lock")?.date?.time
+		if (!latest || !secondsPast(latest, 6 * 60) || secondsPast(state.lastPoll, 55 * 60)) {
+			cmds << secure(zwave.doorLockV1.doorLockOperationGet())
+			state.lastPoll = (new Date()).time
+		} else if (!state.MSR) {
+			cmds << zwave.manufacturerSpecificV1.manufacturerSpecificGet().format()
+		} else if (!state.fw) {
+			cmds << zwave.versionV1.versionGet().format()
+		} else if (!state.codes) {
+			state.pollCode = 1
+			cmds << secure(zwave.userCodeV1.usersNumberGet())
+		} else if (state.pollCode && state.pollCode <= state.codes) {
+			cmds << requestCode(state.pollCode)
+		} else if (!state.lastbatt || (new Date().time) - state.lastbatt > 53*60*60*1000) {
+			cmds << secure(zwave.batteryV1.batteryGet())
+		} else if (!state.enc) {
+			encryptCodes()
+			state.enc = 1
+		}
+	}
+	log.debug "poll is sending ${cmds.inspect()}"
+	device.activity()
+	cmds ?: null
+}
+
+private def encryptCodes() {
+	def keys = new ArrayList(state.keySet().findAll { it.startsWith("code") })
+	keys.each { key ->
+		def match = (key =~ /^code(\d+)$/)
+		if (match) try {
+			def keynum = match[0][1].toInteger()
+			if (keynum > 30 && !state[key]) {
+				state.remove(key)
+			} else if (state[key] && !state[key].startsWith("~")) {
+				log.debug "encrypting $key: ${state[key].inspect()}"
+				state[key] = encrypt(state[key])
+			}
+		} catch (java.lang.NumberFormatException e) { }
 	}
 }
 
@@ -651,7 +672,7 @@ private Boolean secondsPast(timestamp, seconds) {
 			return true
 		}
 	}
-	return (now() - timestamp) > (seconds * 1000)
+	return (new Date().time - timestamp) > (seconds * 1000)
 }
 
 private allCodesDeleted() {

smartapps/brianwarner/light-up-the-night.src/light-up-the-night.groovy

@@ -1,105 +0,0 @@
-/**
- *  Light Up The Night
- *
- *  Copyright 2015 Brian Warner
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-definition(
-    name: "Light Up The Night",
-    namespace: "brianwarner",
-    author: "Brian Warner",
-    description: "Turn on certain lights when a door opens at night, and turn them off a certain time after the last door closes.  Great for garage doors and driveway lights.",
-    category: "Convenience",
-    iconUrl: "http://cdn.device-icons.smartthings.com/Lighting/light9-icn.png",
-    iconX2Url: "http://cdn.device-icons.smartthings.com/Lighting/light9-icn@2x.png",
-    iconX3Url: "http://cdn.device-icons.smartthings.com/Lighting/light9-icn@3x.png")
-
-
-preferences {
-
-section() {
-    	input "contactsensors", "capability.contactSensor", multiple: true, title: "When these doors open:"
-	}
-    
-    section() {
-		input "lights", "capability.switch", required: true, multiple: true, title: "Turn on these lights:"
-    }
-    
-   section() {
-    	input "timer", "number", required: true, title: "Keep them on until all doors are closed for this many minutes:", range: "0..240"
-	}
-    
-    section() {
-    	input "sunriseoffset", "number", required: true, title: "Start turning on the lights this many minutes before sunset:", range: "0..360"
-    }
-
-    section() {
-    	input "sunsetoffset", "number", required: true, title: "Stop turning on the lights this many minutes after sunrise:", range: "0..360"
-    }
-}
-
-def installed() {
-	log.debug "Installed with settings: ${settings}"
-
-	initialize()
-}
-
-def updated() {
-	log.debug "Updated with settings: ${settings}"
-
-	unsubscribe()
-	initialize()
-}
-
-def initialize() {
-	subscribe(garagedoors, "door.open", doorOpenHandler)
-    subscribe(garagedoors, "door.closed", doorClosedHandler)
-	subscribe(contactsensors, "contact.open", doorOpenHandler)
-    subscribe(contactsensors, "contact.closed", doorClosedHandler)
-}
-
-def doorOpenHandler(evt) {
-//	log.debug "Door opened."
-	def now = new Date()
-	def sunTime = getSunriseAndSunset(sunriseOffset: "00:$sunriseoffset", sunsetOffset: "-00:$sunsetoffset")
-
-	if (now > sunTime.sunset || now < sunTime.sunrise) {
-//		log.debug "Turning lights on."
-		lights.on()
-    }
-}
-
-def doorClosedHandler(evt) {
-//	log.debug "A door closed."
-	runIn(60 * timer, checkClosed)
-}
-
-def checkClosed() {
-//	log.debug "Checking to ensure all doors are still closed."
-    
-	def contactSensorState = contactsensors.currentState("contact")
-	def anyContactSensorsOpen = contactSensorState.value.findAll {it == "open"}
-    
-    if (!anyContactSensorsOpen) {
-		def elapsed = now() - contactSensorState.date.time.max()
-	    def timeout = 1000 * 60 * timer
-    
-	    if (elapsed >= timeout) {
-//	    	log.debug "Doors have stayed closed. Turning off the lights."
-	        lights.off()
-    	} else {
-//   		log.debug "Doors were opened. Wait a little longer."
-	    }
-	} else {
-//    	log.debug "It appears a door is still open."
-    }
-}

smartapps/smartthings/button-controller.src/button-controller.groovy

@@ -246,9 +246,6 @@ def toggle(devices) {
 	else if (devices*.currentValue('lock').contains('locked')) {
 		devices.unlock()
 	}
-	else if (devices*.currentValue('lock').contains('unlocked')) {
-		devices.lock()
-	}
 	else if (devices*.currentValue('alarm').contains('off')) {
         devices.siren()
     }

smartapps/smartthings/life360-connect.src/life360-connect.groovy

@@ -592,7 +592,7 @@ def updated() {
         	// log.debug "External Id=${app.id}:${member.id}"
        
        		// create the device
-       		def childDevice = addChildDevice("smartthings", "Life360 User", "${app.id}.${member.id}",null,[name:member.firstName, completedSetup: true])
+       		def childDevice = addChildDevice("smartthings", "life360-user", "${app.id}.${member.id}",null,[name:member.firstName, completedSetup: true])
             // childDevice.setMemberId(member.id)
         
         	if (childDevice)

smartapps/smartthings/wemo-connect.src/wemo-connect.groovy

@@ -78,7 +78,7 @@ def firstPage()
 		def motionsDiscovered = motionsDiscovered()
 		def lightSwitchesDiscovered = lightSwitchesDiscovered()
 
-		return dynamicPage(name:"firstPage", title:"Discovery Started!", nextPage:"", refreshInterval: refreshInterval, install:true, uninstall: true) {
+		return dynamicPage(name:"firstPage", title:"Discovery Started!", nextPage:"", refreshInterval: refreshInterval, install:true, uninstall: selectedSwitches != null || selectedMotions != null || selectedLightSwitches != null) {
 			section("Select a device...") {
 				input "selectedSwitches", "enum", required:false, title:"Select Wemo Switches \n(${switchesDiscovered.size() ?: 0} found)", multiple:true, options:switchesDiscovered
 				input "selectedMotions", "enum", required:false, title:"Select Wemo Motions \n(${motionsDiscovered.size() ?: 0} found)", multiple:true, options:motionsDiscovered