MSA-692: Allows control of Aeon Micro Motor Controller, a Z-Wave device, both from the mobile app tiles, and SmartApps. The device type maps the three hardware states into ST: Up, Down, Stop, and provides commands with the same names. When used with motor shades, generally the motor has an adjustable automatic stop at the full height or extension of the shade, so the physical switch would just select Up, and that was that. The motor stopped despite the switch. The physical switch would typically also have an Off position. The micro motor controller does as well, hence the stop() command. Below is the ReadMe for this device type:

To use this device type in SmartApps, use "capability.doorControl" in Preferences to select the controller. Then you can reference the state of the device with device.currentValue("motor") or device.currentMotor. The device can be in one of three states: up, down, stop, e.g. if(device.currentMotor == "up") {...} There are three commands available: up(), down(), stop(), e.g. device.up() After you include the Aeon device into ST, edit its device type in the IDE to be "Aeon Motor Controller" Down turns on motor M1, and Up turns on motor M2.
Merge pull request #291 from kwarodom/LiFXProd
2026-03-09 21:03:00 +00:00 · 2015-11-17 17:23:58 -06:00 · 2015-11-17 15:00:30 -08:00 · 2015-11-17 10:40:04 -08:00 · 2015-11-17 10:38:01 -08:00 · 2015-11-17 10:38:01 -08:00
22 changed files with 187 additions and 40 deletions
--- a/devicetypes/bravenel/aeon-motor-controller.src/aeon-motor-controller.groovy
+++ b/devicetypes/bravenel/aeon-motor-controller.src/aeon-motor-controller.groovy
@@ -0,0 +1,145 @@
+/**
+ *  Aeon Motor Controller
+ *
+ *  Copyright 2015 Bruce Ravenel
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+metadata {
+	definition (name: "Aeon Motor Controller", namespace: "bravenel", author: "Bruce Ravenel") {
+		capability "Refresh"
+		capability "Actuator"
+        capability "doorControl"
+        capability "Switch"
+
+        command "up"
+        command "down"
+        command "stop"
+
+//		fingerprint inClusters: "0x26,0x32"
+	}
+
+	simulator {
+        status "up":   "command: 2604, payload: FF"
+        status "down": "command: 2604, payload: 00"
+        status "stop": "command: 2605, payload: FE"
+
+		["FF", "FE", "00"].each { val ->
+			reply "2001$val,delay 100,2602": "command: 2603, payload: $val"
+		}
+	}
+
+	tiles {
+		standardTile("motor", "device.motor", width: 2, height: 2) {
+			state("stopUp", label:'stop', icon:"st.doors.garage.garage-open", action: 'down', backgroundColor:"#79b821")
+			state("stopDn", label:'stop', icon:"st.doors.garage.garage-closed", action: 'up', backgroundColor:"#79b821")
+			state("up", label:'up', icon:"st.doors.garage.garage-opening", action:'stop', backgroundColor:"#ffe71e")
+			state("down", label:'down', icon:"st.doors.garage.garage-closing", action:'stop', backgroundColor:"#ffe71e")
+		}
+		valueTile("energy", "device.energy", decoration: "flat") {
+			state "default", label:' '
+		}
+		standardTile("refresh", "device.switch", inactiveLabel: false, decoration: "flat") {
+			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
+		}
+        standardTile("stop", "device.switch") {
+        	state "default", label:"", action: "stop", icon:"http://cdn.device-icons.smartthings.com/sonos/stop-btn@2x.png"
+        }
+        standardTile("up", "device.switch") {
+        	state "default", label: "Up", action: "up", icon:"http://cdn.device-icons.smartthings.com/thermostat/thermostat-up@2x.png"
+        }
+        standardTile("down", "device.switch") {
+        	state "default", label: "Down", action: "down", icon:"http://cdn.device-icons.smartthings.com/thermostat/thermostat-down@2x.png"
+        }
+	}
+	main(["motor"])
+	details(["motor",  "refresh", "energy", "up", "down", "stop",])
+}
+
+// parse events into attributes
+def parse(String description) {
+	def result = []
+	def cmd = zwave.parse(description, [0x20: 1, 0x26: 3])
+	if (cmd) {
+		result = zwaveEvent(cmd)
+		log.debug("'$description' parsed to $result")
+	} else {
+		log.debug("Couldn't zwave.parse '$description'")
+	}
+	result
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.basicv1.BasicReport cmd) {
+	motorEvents(cmd)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.basicv1.BasicSet cmd) {
+	motorEvents(cmd)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.switchmultilevelv3.SwitchMultilevelReport cmd) {
+	motorEvents(cmd)
+}
+
+def motorEvents(physicalgraph.zwave.Command cmd) {
+	def result = []
+    def switchEvent = []
+    if(cmd.value == 0) {switchEvent = createEvent(name: "motor", value: "down", descriptionText: text)}
+    else if(cmd.value == 254) {
+    	def stopVal = state.up ? "stopUp" : "stopDn"
+    	switchEvent = createEvent(name: "motor", value: stopVal, descriptionText: text)
+    }
+    else if(cmd.value == 255) {switchEvent = createEvent(name: "motor", value: "up", descriptionText: text)}
+	result << switchEvent
+}
+
+def refresh() {
+	zwave.switchMultilevelV1.switchMultilevelGet().format()
+}
+
+def up() {
+	state.up = true
+	delayBetween([
+    	zwave.basicV1.basicSet(value: 0xFF).format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}
+
+def down() {
+	state.up = false
+	delayBetween([
+    	zwave.basicV1.basicSet(value: 0x00).format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}
+
+def stop() {
+	delayBetween([
+    	zwave.switchMultilevelV1.switchMultilevelStopLevelChange().format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}
+
+def on() {
+	state.up = true
+	delayBetween([
+    	zwave.basicV1.basicSet(value: 0xFF).format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}
+
+def off() {
+	state.up = false
+	delayBetween([
+    	zwave.basicV1.basicSet(value: 0x00).format(),
+		zwave.switchMultilevelV1.switchMultilevelGet().format()
+    ], 1000)
+}
--- a/devicetypes/smartthings/centralite-dimmer.src/centralite-dimmer.groovy
+++ b/devicetypes/smartthings/centralite-dimmer.src/centralite-dimmer.groovy
@@ -15,7 +15,6 @@
 *	Author: SmartThings
 *	Date: 2013-12-04
 */
-//DEPRECATED - Using the generic DTH for this device. Users need to be moved before deleting this DTH
 metadata {
 	definition (name: "CentraLite Dimmer", namespace: "smartthings", author: "SmartThings") {
 		capability "Switch Level"
@@ -26,6 +25,7 @@ metadata {
 		capability "Refresh"
 		capability "Sensor"

+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0B04,0B05", outClusters: "0019"
 	}

 	// simulator metadata
--- a/devicetypes/smartthings/harmony-activity.src/harmony-activity.groovy
+++ b/devicetypes/smartthings/harmony-activity.src/harmony-activity.groovy
@@ -14,7 +14,7 @@
 *
 */
 metadata {
-        definition (name: "Harmony Activity", namespace: "smartthings", author: "Juan Risso") {
+        definition (name: "Logitech Harmony Activity", namespace: "smartthings", author: "Juan Risso") {
        capability "Switch"
        capability "Actuator"
 		capability "Refresh"
--- a/devicetypes/smartthings/smartsense-garage-door-multi.src/smartsense-garage-door-multi.groovy
+++ b/devicetypes/smartthings/smartsense-garage-door-multi.src/smartsense-garage-door-multi.groovy
@@ -79,8 +79,8 @@ metadata {
 	}
    
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}    
 }

--- a/devicetypes/smartthings/smartsense-garage-door-sensor-button.src/smartsense-garage-door-sensor-button.groovy
+++ b/devicetypes/smartthings/smartsense-garage-door-sensor-button.src/smartsense-garage-door-sensor-button.groovy
@@ -88,8 +88,8 @@ metadata {
 	}

 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}
 }

--- a/devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy
+++ b/devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy
@@ -43,8 +43,8 @@ metadata {
 				])
 		}
 		section {
-			input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-			input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+			input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+			input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 		}
 	}
 
--- a/devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy
+++ b/devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy
@@ -45,8 +45,8 @@ metadata {
 				])
 		}
 		section {
-			input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-			input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+			input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+			input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 		}
 	}

--- a/devicetypes/smartthings/smartsense-motion-temp-sensor.src/smartsense-motion-temp-sensor.groovy
+++ b/devicetypes/smartthings/smartsense-motion-temp-sensor.src/smartsense-motion-temp-sensor.groovy
@@ -37,8 +37,8 @@ metadata {
 	}

 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}

 	tiles(scale: 2) {
--- a/devicetypes/smartthings/smartsense-multi-sensor.src/smartsense-multi-sensor.groovy
+++ b/devicetypes/smartthings/smartsense-multi-sensor.src/smartsense-multi-sensor.groovy
@@ -61,8 +61,8 @@
 				])
 		}
 		section {
- 			input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
- 			input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+ 			input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+ 			input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 		}
 		section {
 			input("garageSensor", "enum", title: "Do you want to use this sensor on a garage door?", options: ["Yes", "No"], defaultValue: "No", required: false, displayDuringSetup: false)
--- a/devicetypes/smartthings/smartsense-multi.src/smartsense-multi.groovy
+++ b/devicetypes/smartthings/smartsense-multi.src/smartsense-multi.groovy
@@ -43,8 +43,8 @@ metadata {
 	}

 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}

 	tiles(scale: 2) {
--- a/devicetypes/smartthings/smartsense-open-closed-accelerometer-sensor.src/smartsense-open-closed-accelerometer-sensor.groovy
+++ b/devicetypes/smartthings/smartsense-open-closed-accelerometer-sensor.src/smartsense-open-closed-accelerometer-sensor.groovy
@@ -32,8 +32,8 @@
 	}

 	preferences {
- 		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
- 		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+ 		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+ 		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}

 	tiles(scale: 2) {
--- a/devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy
+++ b/devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy
@@ -34,8 +34,8 @@ metadata {
 	}

 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}
 
 	tiles(scale: 2) {
--- a/devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy
+++ b/devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy
@@ -33,8 +33,8 @@ metadata {
 	}

 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}

 	tiles(scale: 2) {
--- a/devicetypes/smartthings/smartsense-virtual-open-closed.src/smartsense-virtual-open-closed.groovy
+++ b/devicetypes/smartthings/smartsense-virtual-open-closed.src/smartsense-virtual-open-closed.groovy
@@ -45,8 +45,8 @@ metadata {
 	}
    
 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}    

 	tiles {
--- a/devicetypes/smartthings/tyco-door-window-sensor.src/tyco-door-window-sensor.groovy
+++ b/devicetypes/smartthings/tyco-door-window-sensor.src/tyco-door-window-sensor.groovy
@@ -33,8 +33,8 @@ metadata {
 	}

 	preferences {
-		input title: "Temperature Offset", description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
-		input "tempOffset", "number", title: "Degrees", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
+		input description: "This feature allows you to correct any temperature variations by selecting an offset. Ex: If your sensor consistently reports a temp that's 5 degrees too warm, you'd enter \"-5\". If 3 degrees too cold, enter \"+3\".", displayDuringSetup: false, type: "paragraph", element: "paragraph"
+		input "tempOffset", "number", title: "Temperature Offset", description: "Adjust temperature by this many degrees", range: "*..*", displayDuringSetup: false
 	}
 
 	tiles {
--- a/devicetypes/smartthings/zigbee-dimmer-power.src/zigbee-dimmer-power.groovy
+++ b/devicetypes/smartthings/zigbee-dimmer-power.src/zigbee-dimmer-power.groovy
@@ -25,8 +25,8 @@ metadata {
        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B04"
        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702"
        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "0019", manufacturer: "sengled", model: "Z01-CIA19NAE26", deviceJoinName: "Sengled Element touch"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "000A, 0019", manufacturer: "Jasco Products", model: "45852", deviceJoinName: "GE Zigbee Plug-In Dimmer"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702, 0B05", outClusters: "000A, 0019", manufacturer: "Jasco Products", model: "45857", deviceJoinName: "GE Zigbee In-Wall Dimmer"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0B05,0702", outClusters: "000A,0019", manufacturer: "Jasco Products", model: "45852", deviceJoinName: "GE Zigbee Plug-In Dimmer"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0B05,0702", outClusters: "000A,0019", manufacturer: "Jasco Products", model: "45857", deviceJoinName: "GE Zigbee In-Wall Dimmer"
    }

    tiles(scale: 2) {
--- a/devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy
+++ b/devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy
@@ -17,14 +17,15 @@ metadata {
        capability "Actuator"
        capability "Configuration"
        capability "Refresh"
+        capability "Sensor"
        capability "Switch"
        capability "Switch Level"


        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008"
        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 ON/OFF/DIM", deviceJoinName: "OSRAM LIGHTIFY LED Smart Connected Light"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, FF00", outClusters: "0019", manufacturer: "MRVL", model: "MZ100", deviceJoinName: "Wemo Bulb"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B05", outClusters: "0019", manufacturer: "OSRAM SYLVANIA", model: "iQBR30", deviceJoinName: "Sylvania Ultra iQ"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,FF00", outClusters: "0019", manufacturer: "MRVL", model: "MZ100", deviceJoinName: "Wemo Bulb"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0B05", outClusters: "0019", manufacturer: "OSRAM SYLVANIA", model: "iQBR30", deviceJoinName: "Sylvania Ultra iQ"
    }

    tiles(scale: 2) {
--- a/devicetypes/smartthings/zigbee-switch-power.src/zigbee-switch-power.groovy
+++ b/devicetypes/smartthings/zigbee-switch-power.src/zigbee-switch-power.groovy
@@ -23,8 +23,8 @@ metadata {

        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0B04"
        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0702"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0702, 0B05", outClusters: "0003, 000A, 0019", manufacturer: "Jasco Products", model: "45853", deviceJoinName: "GE ZigBee Plug-In Switch"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0702, 0B05", outClusters: "000A, 0019", manufacturer: "Jasco Products", model: "45856", deviceJoinName: "GE ZigBee In-Wall Switch"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0B05,0702", outClusters: "0003, 000A,0019", manufacturer: "Jasco Products", model: "45853", deviceJoinName: "GE ZigBee Plug-In Switch"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0B05,0702", outClusters: "000A,0019", manufacturer: "Jasco Products", model: "45856", deviceJoinName: "GE ZigBee In-Wall Switch"
    }

    tiles(scale: 2) {
--- a/devicetypes/smartthings/zigbee-switch.src/zigbee-switch.groovy
+++ b/devicetypes/smartthings/zigbee-switch.src/zigbee-switch.groovy
@@ -17,6 +17,7 @@ metadata {
        capability "Actuator"
        capability "Configuration"
        capability "Refresh"
+        capability "Sensor"
        capability "Switch"

        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006"
--- a/devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/zigbee-white-color-temperature-bulb.groovy
+++ b/devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/zigbee-white-color-temperature-bulb.groovy
@@ -23,18 +23,18 @@ metadata {
        capability "Color Temperature"
        capability "Configuration"
        capability "Refresh"
+        capability "Sensor"
        capability "Switch"
        capability "Switch Level"

        attribute "colorName", "string"
        command "setGenericName"

-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300", outClusters: "0019"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04", outClusters: "0019"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY BR Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Flood BR30 Tunable White"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY RT Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Recessed Kit RT 5/6 Tunable White"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Classic A60 TW", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
-        fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04", outClusters: "0019"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY BR Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Flood BR30 Tunable White"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY RT Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Recessed Kit RT 5/6 Tunable White"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Classic A60 TW", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
+        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
    }

    // UI tile definitions
--- a/smartapps/smartthings/life360-connect.src/life360-connect.groovy
+++ b/smartapps/smartthings/life360-connect.src/life360-connect.groovy
@@ -592,7 +592,7 @@ def updated() {
        	// log.debug "External Id=${app.id}:${member.id}"
       
       		// create the device
-       		def childDevice = addChildDevice("smartthings", "Life360 User", "${app.id}.${member.id}",null,[name:member.firstName, completedSetup: true])
+       		def childDevice = addChildDevice("smartthings", "life360-user", "${app.id}.${member.id}",null,[name:member.firstName, completedSetup: true])
            // childDevice.setMemberId(member.id)
        
        	if (childDevice)
--- a/smartapps/smartthings/wemo-connect.src/wemo-connect.groovy
+++ b/smartapps/smartthings/wemo-connect.src/wemo-connect.groovy
@@ -78,7 +78,7 @@ def firstPage()
 		def motionsDiscovered = motionsDiscovered()
 		def lightSwitchesDiscovered = lightSwitchesDiscovered()

-		return dynamicPage(name:"firstPage", title:"Discovery Started!", nextPage:"", refreshInterval: refreshInterval, install:true, uninstall: true) {
+		return dynamicPage(name:"firstPage", title:"Discovery Started!", nextPage:"", refreshInterval: refreshInterval, install:true, uninstall: selectedSwitches != null || selectedMotions != null || selectedLightSwitches != null) {
 			section("Select a device...") {
 				input "selectedSwitches", "enum", required:false, title:"Select Wemo Switches \n(${switchesDiscovered.size() ?: 0} found)", multiple:true, options:switchesDiscovered
 				input "selectedMotions", "enum", required:false, title:"Select Wemo Motions \n(${motionsDiscovered.size() ?: 0} found)", multiple:true, options:motionsDiscovered
Author	SHA1	Message	Date
Bruce Ravenel	9ee81263b1	MSA-692: Allows control of Aeon Micro Motor Controller, a Z-Wave device, both from the mobile app tiles, and SmartApps. The device type maps the three hardware states into ST: Up, Down, Stop, and provides commands with the same names. When used with motor shades, generally the motor has an adjustable automatic stop at the full height or extension of the shade, so the physical switch would just select Up, and that was that. The motor stopped despite the switch. The physical switch would typically also have an Off position. The micro motor controller does as well, hence the stop() command. Below is the ReadMe for this device type: To use this device type in SmartApps, use "capability.doorControl" in Preferences to select the controller. Then you can reference the state of the device with device.currentValue("motor") or device.currentMotor. The device can be in one of three states: up, down, stop, e.g. if(device.currentMotor == "up") {...} There are three commands available: up(), down(), stop(), e.g. device.up() After you include the Aeon device into ST, edit its device type in the IDE to be "Aeon Motor Controller" Down turns on motor M1, and Up turns on motor M2.	2015-11-17 17:23:58 -06:00
Vinay Rao	01a36696d8	Merge pull request #291 from kwarodom/LiFXProd LiFX - LiFX: update oauth/callback url using getApiServerUrl() for shard proxying and change shardUrl param to apiServerUrl	2015-11-17 15:00:30 -08:00
Yaima Valdivia	797def2935	Merge branch 'master' of github.com:SmartThingsCommunity/SmartThingsPublic	2015-11-17 10:40:04 -08:00
Yaima Valdivia	1034cd06e6	Var names reversed	2015-11-17 10:38:01 -08:00
Vinay Rao	c37729242e	temporary changes to the lock DTH to account for the upcoming zigbee library changes	2015-11-17 10:38:01 -08:00
Vinay Rao	d29c3ec557	Cree DTH refresh	2015-11-17 10:38:01 -08:00
Vinay Rao	17be85b846	Moving re-certified device to generic zigbee DTH.	2015-11-17 10:38:01 -08:00
Vinay Rao	da06104563	Adding fingerprint for new bulbs and transition old color temperature osram bulbs to new one	2015-11-17 10:38:01 -08:00
Vinay Rao	5d37ac8515	new fingerprints for Yale. battery issue resolution for Yale	2015-11-17 10:38:01 -08:00
Vinay Rao	2a739fda07	adding fingerprints for osram and sengled dimmable bulbs	2015-11-17 10:38:01 -08:00
Juan Pablo Risso	f627fb4fac	Reverted to previously working getBridgeIP()	2015-11-17 10:38:01 -08:00
Juan Pablo Risso	1d30a718b2	Replaced atomicState with State	2015-11-17 10:38:01 -08:00
Juan Pablo Risso	303ca7117c	Added a ","	2015-11-17 10:38:01 -08:00
Juan Pablo Risso	1c96645b9f	removed function ShardUrl()	2015-11-17 10:38:00 -08:00
Juan Pablo Risso	af4dc0640a	added singleInstance: true	2015-11-17 10:38:00 -08:00
juano2310	80b46153dc	Harmony Global Oauth	2015-11-17 10:38:00 -08:00
Mike Robinet	b92cd9c637	CREX-1094 Delete stale device subscriptions on IFTTT app update	2015-11-17 10:38:00 -08:00
Juan Pablo Risso	1039b65c81	Code Cleanup	2015-11-17 10:38:00 -08:00
juano2310	4e203e8e13	buildActionUrl("hookCallback")	2015-11-17 10:38:00 -08:00
juano2310	61398105d1	Jawbone Global Oauth	2015-11-17 10:38:00 -08:00
bflorian	505efc5463	Deleted lights on when door opens after sundown	2015-11-17 10:38:00 -08:00
bflorian	3ddc82f996	More name/namespace changes	2015-11-17 10:38:00 -08:00
Juan Pablo Risso	13a324069d	Force Level = 1% to 1 This ensures that the bulb will be able to dim to it minimum	2015-11-17 10:38:00 -08:00
bflorian	2fd5859326	Misc filename and namespace changes.	2015-11-17 10:38:00 -08:00
bflorian	bbedbddf9d	Filename corrections	2015-11-17 10:38:00 -08:00
bflorian	e424e7abdd	Corrected filename of Z-Wave Device Multichannel	2015-11-17 10:38:00 -08:00
Tom Manley	47fbdabf6b	Fix 'Low Battery Handler' exception caused by non-integer battery events ZigBee locks report battery percentage remaining in .5% increments. However the Low Battery Handler Smart App in Hello Home expects it to be an integer.	2015-11-17 10:37:59 -08:00
Mike Robinet	7defe1cc61	CREX-3129 Update parent and service manager apps to be singleton	2015-11-17 10:37:59 -08:00
Mike Cousins	a78459347b	update keen home smart vent device handler	2015-11-17 10:37:59 -08:00
juano2310	c473745e47	Wemo refactor final (DVCSMP-1189) https://smartthings.atlassian.net/browse/DVCSMP-1189 Detect and mark device offline within 5 minutes. Show Device offline in device tile. Show Device offline in Recent Activity. Log the current IP address to Recent Activity. Log the changed IP address to Recent Activity. Support 'Turning on' and 'Turning off' (blindly changing the state of device to ON or OFF without confirming bulb responded correctly) Turn on / off through Wemo-App reflected timely in SmartThings App/Ecosystem. Manual turn on / off of device is reflected timely in SmartThings App/Ecosystem. Lower case createEvent Bug Fixes Bug fixes setOffline Minor cosmetic fixes	2015-11-17 10:37:59 -08:00
Juan Pablo Risso	fc587ef15a	Fix to Hue reverts dimmer settings (DVCSMP-1227) if you use the hue native app to adjust the dimmer setting, smartthings will reset the dimmer to previous value when toggling from ST app (and automations)	2015-11-17 10:37:59 -08:00
Warodom Khamphanchai	0f3b730f26	DVCSMP-668 - Show batteryStatus tile insteady of battery tile to be able to display both when sensor is USB powered or battery powered - Remove background for illuminance. This can be added when we have best practice of showing colors for lux. - Instead of using powerSupply:failed, configurationGet cmd is sent and then the configure() is triggered by configurationReport to determine powerSupply (USB Cable/Battery) - Instead of querying battery level on wake up, battery report is put in association group 2 that is configured to report every 6 hours by default - Update configure() to send both unsecure and secure configuration commands when sensor is joined normally or securely	2015-11-17 10:37:59 -08:00
Warodom Khamphanchai	11df2f31b3	DVCSMP-668 The following changes has been made to the original Aeon Multisensor device type handler to improve and modernize it: 1. Add "powerSupply" attribute to be able to tell power source (USB Cable/Battery) 2. Add preference page for user to customize "motion delay time", "motion sensitivity", and "sensor report interval" 3. Add color backgroud of "illuminance" value tile 4. Add tile for "ultravioletIndex" 5. Add tile for "powerSupply" 6. Modify updated() to be able to send configuration commands to sensor whether it is powered by USB cable or battery 7. When battery operated, send command to get update battery level if it hasn't been reported for a while 8. Report MSR of the sensor 9. Add handle for ConfigurationReport command class to update the "powerSupply" tile and change opetion mode of the sensor accordingly 10. Update configure() to configure parameters changed by user in preference page 11. Take out the "Configure" tile and instead send the configuration commands on every wakeup (sensor is battey powered)	2015-11-17 10:37:59 -08:00
Yaima Valdivia	4d243bf44d	Rename Sonos SmartApps https://smartthings.atlassian.net/browse/DVCSMP-607	2015-10-27 12:29:05 -07:00