Merge pull request #1555 from skt123/micro_smart_switch

[CHF-493] Added Health Check Implementation for Micro Smart Switch 2E.

devicetypes/smartthings/aeon-multisensor-gen5.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/aeon-multisensor-gen5.src/README.md

@@ -0,0 +1,43 @@
+# Aeon Multisensor Gen5
+
+Cloud Execution
+
+Works with: 
+
+* [Aeon Labs MultiSensor (Gen 5)](https://www.smartthings.com/works-with-smartthings/sensors/aeon-labs-multisensor-gen-5)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Motion Sensor** - can detect motion
+* **Temperature Measurement** - defines device measures current temperature
+* **Relative Humidity Measurement** - allow reading the relative humidity from devices that support it
+* **Illuminance Measurement** - gives the illuminance reading from devices that support it
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Sensor** - detects sensor events
+* **Battery** - defines device uses a battery
+* **Health Check** - indicates ability to get device health notifications
+
+
+## Device Health
+
+Aeon Labs MultiSensor (Gen 5) is polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+* __32min__ checkInterval
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Aeon Labs MultiSensor (Gen 5) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/206157226-Aeon-Labs-MultiSensor-Gen-5-)

devicetypes/smartthings/aeon-multisensor-gen5.src/aeon-multisensor-gen5.groovy

@@ -20,10 +20,12 @@ metadata {
 		capability "Configuration"
 		capability "Sensor"
 		capability "Battery"
+		capability "Health Check"
 
 		command "configureAfterSecure"
 
 		fingerprint deviceId: "0x0701", inClusters: "0x5E,0x86,0x72,0x59,0x85,0x73,0x71,0x84,0x80,0x30,0x31,0x70,0x98,0x7A", outClusters:"0x5A"
+		fingerprint mfr:"0086", prod:"0102", model:"004A", deviceJoinName: "Aeon Labs MultiSensor (Gen 5)"
 	}
 
 	simulator {
@@ -98,6 +100,11 @@ metadata {
 	}
 }
 
+def updated(){
+// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description)
 {
 	def result = null
@@ -244,6 +251,13 @@ def configureAfterSecure() {
     secureSequence(request) + ["delay 20000", zwave.wakeUpV1.wakeUpNoMoreInformation().format()]
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	secure(zwave.batteryV1.batteryGet())
+}
+
 def configure() {
 	// log.debug "configure()"
     //["delay 30000"] + secure(zwave.securityV1.securityCommandsSupportedGet())

devicetypes/smartthings/aeon-siren.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/aeon-siren.src/README.md

@@ -0,0 +1,37 @@
+# Aeon Siren
+
+Cloud Execution
+
+Works with: 
+
+* [Aeon Labs Siren (Gen 5)](https://www.smartthings.com/works-with-smartthings/aeon-labs/aeon-labs-siren-gen-5)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Alarm** - allows for interacting with devices that serve as alarms
+* **Switch** - can detect state (possible values: on/off)
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Aeon Labs Siren (Gen 5) is polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+* __32min__ checkInterval
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Aeon Labs Siren (Gen 5) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/204555240-Aeon-Labs-Siren-Gen-5-)

devicetypes/smartthings/aeon-siren.src/aeon-siren.groovy

@@ -20,10 +20,11 @@ metadata {
 	capability "Actuator"
 	capability "Alarm"
 	capability "Switch"
+	capability "Health Check"
 
 	command "test"
 
-	fingerprint deviceId: "0x1005", inClusters: "0x5E,0x98"
+	fingerprint deviceId: "0x1005", inClusters: "0x5E,0x98", deviceJoinName: "Aeon Labs Siren (Gen 5)"
  }
 
  simulator {
@@ -58,6 +59,9 @@ metadata {
 }
 
 def updated() {
+// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+
 	if(!state.sound) state.sound = 1
 	if(!state.volume) state.volume = 3
 
@@ -148,3 +152,10 @@ def test() {
 private secure(physicalgraph.zwave.Command cmd) {
 	zwave.securityV1.securityMessageEncapsulation().encapsulate(cmd).format()
 }
+
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	secure(zwave.basicV1.basicGet())
+}

devicetypes/smartthings/fortrezz-water-valve.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/fortrezz-water-valve.src/README.md

@@ -0,0 +1,39 @@
+# FortrezZ Water Valve
+
+Cloud Execution
+
+Works with: 
+
+* [FortrezZ Water Valve](https://www.smartthings.com/works-with-smartthings/other/fortrezz-water-valve)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Health Check** - indicates ability to get device health notifications
+* **Valve** - allows for the control of a valve device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+
+## Device Health
+
+FortrezZ Water Valve is polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+* __32min__ checkInterval
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [FortrezZ Water Valve Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/202088434-FortrezZ-Water-Valve-Shutoff)

devicetypes/smartthings/fortrezz-water-valve.src/fortrezz-water-valve.groovy

@@ -14,11 +14,13 @@
 metadata {
 	definition (name: "Fortrezz Water Valve", namespace: "smartthings", author: "SmartThings") {
 		capability "Actuator"
+		capability "Health Check"
 		capability "Valve"
 		capability "Refresh"
 		capability "Sensor"
         
 		fingerprint deviceId: "0x1000", inClusters: "0x25,0x72,0x86,0x71,0x22,0x70"
+		fingerprint mfr:"0084", prod:"0213", model:"0215", deviceJoinName: "FortrezZ Water Valve"
 	}
 
 	// simulator metadata
@@ -48,6 +50,11 @@ metadata {
 	}
 }
 
+def updated(){
+// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description) {
 	log.trace description
 	def result = null
@@ -76,6 +83,13 @@ def close() {
 	zwave.switchBinaryV1.switchBinarySet(switchValue: 0xFF).format()
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	zwave.switchBinaryV1.switchBinaryGet().format()
 }

devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy

@@ -107,6 +107,12 @@ def parse(String description) {
 				}
 			}
 		}
+	} else if (map.name == "temperature") {
+		if (tempOffset) {
+			map.value = (int) map.value + (int) tempOffset
+		}
+		map.descriptionText = temperatureScale == 'C' ? '{{ device.displayName }} was {{ value }}°C' : '{{ device.displayName }} was {{ value }}°F'
+		map.translatable = true
 	}
 
 	log.debug "Parse returned $map"

devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy

@@ -113,6 +113,12 @@ def parse(String description) {
 				map = getMotionResult(value)
 			}
 		}
+	} else if (map.name == "temperature") {
+		if (tempOffset) {
+			map.value = (int) map.value + (int) tempOffset
+		}
+		map.descriptionText = temperatureScale == 'C' ? '{{ device.displayName }} was {{ value }}°C' : '{{ device.displayName }} was {{ value }}°F'
+		map.translatable = true
 	}
 
 	log.debug "Parse returned $map"

devicetypes/smartthings/smartsense-multi.src/smartsense-multi.groovy

@@ -52,7 +52,7 @@ metadata {
 	tiles(scale: 2) {
 		multiAttributeTile(name:"contact", type: "generic", width: 6, height: 4){
 			tileAttribute ("device.contact", key: "PRIMARY_CONTROL") {
-				attributeState "open", label:'${name}', icon:"st.contact.contact.open", backgroundColor:"##e86d13"
+				attributeState "open", label:'${name}', icon:"st.contact.contact.open", backgroundColor:"#e86d13"
 				attributeState "closed", label:'${name}', icon:"st.contact.contact.closed", backgroundColor:"#00a0dc"
 			}
 		}

devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy

@@ -95,6 +95,12 @@ def parse(String description) {
 				}
 			}
 		}
+	} else if (map.name == "temperature") {
+		if (tempOffset) {
+			map.value = (int) map.value + (int) tempOffset
+		}
+		map.descriptionText = temperatureScale == 'C' ? '{{ device.displayName }} was {{ value }}°C' : '{{ device.displayName }} was {{ value }}°F'
+		map.translatable = true
 	}
 
 	log.debug "Parse returned $map"

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy

@@ -88,6 +88,12 @@ def parse(String description) {
 				log.warn "TEMP REPORTING CONFIG FAILED- error code: ${descMap.data[0]}"
 			}
 		}
+	} else if (map.name == "temperature") {
+		if (tempOffset) {
+			map.value = (int) map.value + (int) tempOffset
+		}
+		map.descriptionText = temperatureScale == 'C' ? '{{ device.displayName }} was {{ value }}°C' : '{{ device.displayName }} was {{ value }}°F'
+		map.translatable = true
 	}
 
 	log.debug "Parse returned $map"

devicetypes/smartthings/zwave-garage-door-opener.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-garage-door-opener.src/README.md

@@ -0,0 +1,41 @@
+# Z-wave Garage Door Opener
+
+Cloud Execution
+
+Works with: 
+
+* [Linear GoControl Garage Door Opener](https://www.smartthings.com/works-with-smartthings/other/linear-gocontrol-garage-door-opener)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Door Control** - allow for the control of a door
+* **Garage Door Control** - allow for the control of a garage door
+* **Health Check** - indicates ability to get device health notifications
+* **Contact Sensor** - can detect contact (with possible values - open/closed)
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+
+## Device Health
+
+Linear GoControl Garage Door Opener is polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+* __32min__ checkInterval
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Linear GoControl Garage Door Opener Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/204831116-GoControl-Linear-Garage-Door-Opener-GD00Z-4-)

devicetypes/smartthings/zwave-garage-door-opener.src/zwave-garage-door-opener.groovy

@@ -18,12 +18,14 @@ metadata {
 		capability "Actuator"
 		capability "Door Control"
 		capability "Garage Door Control"
+		capability "Health Check"
 		capability "Contact Sensor"
 		capability "Refresh"
 		capability "Sensor"
 
 		fingerprint deviceId: "0x4007", inClusters: "0x98"
 		fingerprint deviceId: "0x4006", inClusters: "0x98"
+		fingerprint mfr:"014F", prod:"4744", model:"3030", deviceJoinName: "Linear GoControl Garage Door Opener"
 	}
 
 	simulator {
@@ -63,6 +65,11 @@ metadata {
 
 import physicalgraph.zwave.commands.barrieroperatorv1.*
 
+def updated(){
+// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description) {
 	def result = null
 	if (description.startsWith("Err")) {
@@ -287,6 +294,13 @@ def close() {
 	secure(zwave.barrierOperatorV1.barrierOperatorSet(requestedBarrierState: BarrierOperatorSet.REQUESTED_BARRIER_STATE_CLOSE))
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	secure(zwave.barrierOperatorV1.barrierOperatorGet())
 }

devicetypes/smartthings/zwave-lock.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-lock.src/README.md

@@ -0,0 +1,45 @@
+# Z-Wave Switch
+
+Cloud Execution
+
+Works with: 
+
+* [Yale Key Free Touchscreen Deadbolt (YRD240)](https://www.smartthings.com/works-with-smartthings/yale/yale-key-free-touchscreen-deadbolt-yrd240)
+
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#Troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Battery** - defines device uses a battery
+* **Lock** - allows for the control of a lock device
+* **Lock Codes** - allows for the lock code control of a lock device
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Z-Wave Locks are polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+* __32min__ checkInterval
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [General Z-Wave/ZigBee Yale Lock Troubleshooting](https://support.smartthings.com/hc/en-us/articles/205138400-How-to-connect-Yale-locks)
+
+

devicetypes/smartthings/zwave-lock.src/zwave-lock.groovy

@@ -20,11 +20,13 @@ metadata {
 		capability "Sensor"
 		capability "Lock Codes"
 		capability "Battery"
+		capability "Health Check"
 
 		command "unlockwtimeout"
 
 		fingerprint deviceId: "0x4003", inClusters: "0x98"
 		fingerprint deviceId: "0x4004", inClusters: "0x98"
+		fingerprint mfr:"0129", prod:"0002", model:"0000", deviceJoinName: "Yale Key Free Touchscreen Deadbolt"
 	}
 
 	simulator {
@@ -67,6 +69,8 @@ import physicalgraph.zwave.commands.doorlockv1.*
 import physicalgraph.zwave.commands.usercodev1.*
 
 def updated() {
+	// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
 	try {
 		if (!state.init) {
 			state.init = true
@@ -504,6 +508,13 @@ def unlockwtimeout() {
 	lockAndCheck(DoorLockOperationSet.DOOR_LOCK_MODE_DOOR_UNSECURED_WITH_TIMEOUT)
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	def cmds = [secure(zwave.doorLockV1.doorLockOperationGet())]
 	if (state.assoc == zwaveHubNodeId) {

devicetypes/smartthings/zwave-metering-switch.src/zwave-metering-switch.groovy

@@ -22,10 +22,12 @@ metadata {
 		capability "Configuration"
 		capability "Sensor"
 		capability "Light"
+		capability "Health Check"
 
 		command "reset"
 
 		fingerprint inClusters: "0x25,0x32"
+		fingerprint mfr:"0086", prod:"0003", model:"0012", deviceJoinName: "Aeon Labs Micro Smart Switch 2E"
 	}
 
 	// simulator metadata
@@ -73,6 +75,8 @@ metadata {
 }
 
 def updated() {
+	// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
 	try {
 		if (!state.MSR) {
 			response(zwave.manufacturerSpecificV2.manufacturerSpecificGet().format())
@@ -179,6 +183,14 @@ def poll() {
 	])
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	log.debug "ping() called"
+	refresh()
+}
+
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),

devicetypes/smartthings/zwave-siren.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-siren.src/README.md

@@ -0,0 +1,42 @@
+# Z-wave Siren
+
+Cloud Execution
+
+Works with: 
+
+* [FortrezZ Siren Strobe Alarm](https://www.smartthings.com/works-with-smartthings/other/fortrezz-water-valve)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Alarm** - allows for interacting with devices that serve as alarms
+* **Battery** - defines device uses a battery
+* **Health Check** - indicates ability to get device health notifications
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+* **Switch** - can detect state (possible values: on/off)
+
+## Device Health
+
+FortrezZ Siren Strobe Alarm is polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+* __32min__ checkInterval
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [FortrezZ Siren Strobe Alarm Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/202294760-FortrezZ-Siren-Strobe-Alarm)

devicetypes/smartthings/zwave-siren.src/zwave-siren.groovy

@@ -20,6 +20,7 @@ metadata {
 		capability "Actuator"
         capability "Alarm"
         capability "Battery"
+		capability "Health Check"
         capability "Polling"
         capability "Refresh"
         capability "Sensor"
@@ -27,6 +28,7 @@ metadata {
 
 
 		fingerprint inClusters: "0x20,0x25,0x86,0x80,0x85,0x72,0x71"
+		fingerprint mfr:"0084", prod:"0313", model:"010B", deviceJoinName: "FortrezZ Siren Strobe Alarm"
 	}
 
 	simulator {
@@ -58,6 +60,11 @@ metadata {
 	}
 }
 
+def updated(){
+// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def createEvents(physicalgraph.zwave.commands.batteryv1.BatteryReport cmd) {
 	def map = [ name: "battery", unit: "%" ]
 	if (cmd.batteryLevel == 0xFF) {
@@ -119,6 +126,13 @@ def both() {
 	on()
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	log.debug "sending battery refresh command"
 	zwave.batteryV1.batteryGet().format()

devicetypes/smartthings/zwave-smoke-alarm.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-smoke-alarm.src/README.md

@@ -0,0 +1,40 @@
+# Z-wave Smoke Alarm
+
+Cloud Execution
+
+Works with: 
+
+* [First Alert Smoke Detector and Carbon Monoxide Alarm (ZCOMBO)](https://www.smartthings.com/works-with-smartthings/sensors/first-alert-smoke-detector-and-carbon-monoxide-alarm-zcombo)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Smoke Detector** - measure smoke and optionally carbon monoxide levels
+* **Carbon Monoxide Detector** - measure carbon monoxide levels
+* **Sensor** - detects sensor events
+* **Battery** - defines device uses a battery
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+First Alert Smoke Detector and Carbon Monoxide Alarm (ZCOMBO) is a Z-wave sleepy device and checks in every 1 hour.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*60 + 2)mins = 122 mins.
+
+* __122min__ checkInterval
+
+## Battery Specification
+
+Two AA 1.5V batteries are required.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [First Alert Smoke Detector and Carbon Monoxide Alarm (ZCOMBO) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/201581984-First-Alert-Smoke-Detector-and-Carbon-Monoxide-Alarm-ZCOMBO-)

devicetypes/smartthings/zwave-smoke-alarm.src/zwave-smoke-alarm.groovy

@@ -17,10 +17,12 @@ metadata {
 		capability "Carbon Monoxide Detector"
 		capability "Sensor"
 		capability "Battery"
+		capability "Health Check"
 
 		attribute "alarmState", "string"
 
 		fingerprint deviceId: "0xA100", inClusters: "0x20,0x80,0x70,0x85,0x71,0x72,0x86"
+		fingerprint mfr:"0138", prod:"0001", model:"0002", deviceJoinName: "First Alert Smoke Detector and Carbon Monoxide Alarm (ZCOMBO)"
 	}
 
 	simulator {
@@ -51,6 +53,11 @@ metadata {
 	}
 }
 
+def updated(){
+// Device checks in every hour, this interval allows us to miss one check-in notification before marking offline
+	sendEvent(name: "checkInterval", value: 2 * 60 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description) {
 	def results = []
 	if (description.startsWith("Err")) {
@@ -65,7 +72,6 @@ def parse(String description) {
 	return results
 }
 
-
 def createSmokeOrCOEvents(name, results) {
 	def text = null
 	switch (name) {

devicetypes/smartthings/zwave-thermostat.src/zwave-thermostat.groovy

@@ -20,6 +20,7 @@ metadata {
 		capability "Configuration"
 		capability "Polling"
 		capability "Sensor"
+		capability "Health Check"
 		
 		attribute "thermostatFanState", "string"
 
@@ -30,6 +31,7 @@ metadata {
 
 		fingerprint deviceId: "0x08"
 		fingerprint inClusters: "0x43,0x40,0x44,0x31"
+		fingerprint mfr:"0039", prod:"0011", model:"0001", deviceJoinName: "Honeywell Z-Wave Thermostat"
 	}
 
 	// simulator metadata
@@ -123,6 +125,11 @@ metadata {
 	}
 }
 
+def updated(){
+	// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description)
 {
 	def map = createEvent(zwaveEvent(zwave.parse(description, [0x42:1, 0x43:2, 0x31: 3])))
@@ -393,6 +400,14 @@ def setCoolingSetpoint(Double degrees, Integer delay = 30000) {
 	], delay)
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	log.debug "ping() called"
+	poll()
+}
+
 def configure() {
 	delayBetween([
 		zwave.thermostatModeV2.thermostatModeSupportedGet().format(),