MSA-1539: Checks all battery levels daily at a set time and sends a notification if any battery is below the set threshold.

[CHF-425] Health Check Implementation for Z-wave switch

devicetypes/smartthings/dimmer-switch.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/dimmer-switch.src/README.md

@@ -0,0 +1,45 @@
+# Z-wave Dimmer Switch
+
+
+
+Works with:
+
+* [GE Z-Wave In-Wall Smart Dimmer (GE 12724)](http://products.z-wavealliance.org/products/1197)
+* [GE Z-Wave In-Wall Smart Dimmer (Toggle) (GE 12729)](http://products.z-wavealliance.org/products/1201)
+* [GE Z-Wave Plug-in Smart Dimmer (GE 12718)](http://products.z-wavealliance.org/products/1191)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#Troubleshooting)
+
+## Capabilities
+
+* **Switch Level** - it's defined to accept two parameters, the level and the rate of dimming
+* **Actuator** - represents that a Device has commands
+* **Indicator** - gives you the ability to set the indicator LED light on a Z-Wave switch
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Z-Wave Smart Dimmers (In-Wall, In-Wall(Toggle), Plug-In) are polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Check-in interval = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [General Z-Wave Dimmer/Switch Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200955890-Troubleshooting-GE-in-wall-switch-or-dimmer-won-t-respond-to-commands-or-automations-Z-Wave-)
+* [GE Z-Wave In-Wall Smart Dimmer (GE 12724) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200902600-GE-In-Wall-Paddle-Dimmer-Switch-GE-12724-Z-Wave-)
+* [GE Z-Wave In-Wall Smart Dimmer (Toggle) (GE 12729) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/207568463-GE-In-Wall-Smart-Toggle-Dimmer-GE-12729-Z-Wave-)
+* [GE Z-Wave Plug-in Smart Dimmer (GE 12718) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/202088474-GE-Plug-In-Smart-Dimmer-GE-12718-Z-Wave-)

devicetypes/smartthings/dimmer-switch.src/dimmer-switch.groovy

@@ -20,6 +20,7 @@ metadata {
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
+		capability "Health Check"
 
 		fingerprint mfr:"0063", prod:"4457", deviceJoinName: "Z-Wave Wall Dimmer"
 		fingerprint mfr:"0063", prod:"4944", deviceJoinName: "Z-Wave Wall Dimmer"
@@ -82,6 +83,8 @@ metadata {
 }
 
 def updated(){
+	// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
   switch (ledIndicator) {
         case "on":
             indicatorWhenOn()
@@ -215,6 +218,13 @@ def poll() {
 	zwave.switchMultilevelV1.switchMultilevelGet().format()
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	log.debug "refresh() is called"
 	def commands = []

devicetypes/smartthings/leedarson-led-tunable-white.src/leedarson-led-tunable-white.groovy

@@ -1,267 +0,0 @@
-/**
- *  Leedarson Light
- *
- *  Copyright 2016 Jungle
- *
- *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
- *  in compliance with the License. You may obtain a copy of the License at:
- *
- *      http://www.apache.org/licenses/LICENSE-2.0
- *
- *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
- *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
- *  for the specific language governing permissions and limitations under the License.
- *
- */
-/*
-    Osram Tunable White 60 A19 bulb
-
-    Osram bulbs have a firmware issue causing it to forget its dimming level when turned off (via commands). Handling
-    that issue by using state variables
-*/
-
-//DEPRECATED - Using the generic DTH for this device. Users need to be moved before deleting this DTH
-
-metadata {
-    definition (name: "LEEDARSON LED Tunable White", namespace: "smartthings", author: "Yechi") {
-
-        capability "Color Temperature"
-        capability "Actuator"
-        capability "Switch"
-        capability "Switch Level"
-        capability "Configuration"
-        capability "Refresh"
-        capability "Sensor"
-
-        attribute "colorName", "string"
-    }
-
-    // simulator metadata
-    simulator {
-        // status messages
-        status "on": "on/off: 1"
-        status "off": "on/off: 0"
-
-        // reply messages
-        reply "zcl on-off on": "on/off: 1"
-        reply "zcl on-off off": "on/off: 0"
-    }
-
-    // UI tile definitions
-    tiles {
-        standardTile("switch", "device.switch", width: 2, height: 2, canChangeIcon: true) {
-            state "on", label: '${name}', action: "switch.off", icon: "st.switches.light.on", backgroundColor: "#79b821"
-            state "off", label: '${name}', action: "switch.on", icon: "st.switches.light.off", backgroundColor: "#ffffff"
-        }
-        standardTile("refresh", "device.switch", inactiveLabel: false, decoration: "flat") {
-            state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
-        }
-
-        controlTile("colorTempSliderControl", "device.colorTemperature", "slider", height: 1, width: 2, inactiveLabel: false, range:"(2700..5000)") {
-            state "colorTemperature", action:"color temperature.setColorTemperature"
-        }
-        valueTile("colorTemp", "device.colorTemperature", inactiveLabel: false, decoration: "flat") {
-            state "colorTemperature", label: '${currentValue} K'
-        }
-        valueTile("colorName", "device.colorName", inactiveLabel: false, decoration: "flat") {
-            state "colorName", label: '${currentValue}'
-        }
-
-
-        controlTile("levelSliderControl", "device.level", "slider", height: 1, width: 2, inactiveLabel: false, range:"(0..100)") {
-            state "level", action:"switch level.setLevel"
-        }
-        valueTile("level", "device.level", inactiveLabel: false, decoration: "flat") {
-            state "level", label: 'Level ${currentValue}%'
-        }
-
-
-        main(["switch"])
-        details(["switch", "refresh", "colorName", "levelSliderControl", "level", "colorTempSliderControl", "colorTemp"])
-    }
-}
-
-// Parse incoming device messages to generate events
-def parse(String description) {
-    //log.trace description
-
-    if (description?.startsWith("catchall:")) {
-        if(description?.endsWith("0100") ||description?.endsWith("1001") || description?.matches("on/off\\s*:\\s*1"))
-        {
-            def result = createEvent(name: "switch", value: "on")
-            log.debug "Parse returned ${result?.descriptionText}"
-            return result
-        }
-        else if(description?.endsWith("0000") || description?.endsWith("1000") || description?.matches("on/off\\s*:\\s*0"))
-        {
-            def result = createEvent(name: "switch", value: "off")
-            log.debug "Parse returned ${result?.descriptionText}"
-            return result
-        }
-
-    }
-    else if (description?.startsWith("read attr -")) {
-        def descMap = parseDescriptionAsMap(description)
-        log.trace "descMap : $descMap"
-
-        if (descMap.cluster == "0300") {
-            log.debug descMap.value
-            def tempInMired = convertHexToInt(descMap.value)
-            def tempInKelvin = Math.round(1000000/tempInMired)
-            log.trace "temp in kelvin: $tempInKelvin"
-            sendEvent(name: "colorTemperature", value: tempInKelvin, displayed:false)
-        }
-        else if(descMap.cluster == "0008"){
-            def dimmerValue = Math.round(convertHexToInt(descMap.value) * 100 / 255)
-            log.debug "dimmer value is $dimmerValue"
-            sendEvent(name: "level", value: dimmerValue)
-        }
-    }
-    else {
-        def name = description?.startsWith("on/off: ") ? "switch" : null
-        def value = name == "switch" ? (description?.endsWith(" 1") ? "on" : "off") : null
-        def result = createEvent(name: name, value: value)
-        log.debug "Parse returned ${result?.descriptionText}"
-        return result
-    }
-}
-
-def on() {
-    log.debug "on()"
-    sendEvent(name: "switch", value: "on")
-    setLevel(state?.levelValue)
-}
-
-def off() {
-    log.debug "off()"
-    sendEvent(name: "switch", value: "off")
-    "st cmd 0x${device.deviceNetworkId} ${endpointId} 6 0 {}"
-}
-
-def refresh() {
-    [
-            "st rattr 0x${device.deviceNetworkId} ${endpointId} 6 0", "delay 500",
-            "st rattr 0x${device.deviceNetworkId} ${endpointId} 8 0", "delay 500",
-            "st rattr 0x${device.deviceNetworkId} ${endpointId} 0x0300 7"
-    ]
-
-}
-
-def configure() {
-    state.levelValue = 100
-    log.debug "Configuring Reporting and Bindings."
-    def configCmds = [
-            "zdo bind 0x${device.deviceNetworkId} ${endpointId} 1 0x0300 {${device.zigbeeId}} {}", "delay 500"
-    ]
-    return onOffConfig() + levelConfig() + configCmds + refresh() // send refresh cmds as part of config
-}
-
-def onOffConfig() {
-    [
-            "zdo bind 0x${device.deviceNetworkId} ${endpointId} 1 6 {${device.zigbeeId}} {}", "delay 200",
-            "zcl global send-me-a-report 6 0 0x10 0 300 {01}",
-            "send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 1500"
-    ]
-}
-
-//level config for devices with min reporting interval as 5 seconds and reporting interval if no activity as 1hour (3600s)
-//min level change is 01
-def levelConfig() {
-    [
-            "zdo bind 0x${device.deviceNetworkId} ${endpointId} 1 8 {${device.zigbeeId}} {}", "delay 200",
-            "zcl global send-me-a-report 8 0 0x20 5 3600 {01}",
-            "send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 1500"
-    ]
-}
-
-def setColorTemperature(value) {
-    if(value<101){
-        value = (value*23) + 2700		//Calculation of mapping 0-100 to 2700-6500
-    }
-
-    def tempInMired = Math.round(1000000/value)
-    def finalHex = swapEndianHex(hex(tempInMired, 4))
-    def genericName = getGenericName(value)
-    log.debug "generic name is : $genericName"
-
-    def cmds = []
-    sendEvent(name: "colorTemperature", value: value, displayed:false)
-    sendEvent(name: "colorName", value: genericName)
-
-    cmds << "st cmd 0x${device.deviceNetworkId} ${endpointId} 0x0300 0x0a {${finalHex} 2000}"
-
-    cmds
-}
-
-def parseDescriptionAsMap(description) {
-    (description - "read attr - ").split(",").inject([:]) { map, param ->
-        def nameAndValue = param.split(":")
-        map += [(nameAndValue[0].trim()):nameAndValue[1].trim()]
-    }
-}
-
-def setLevel(value) {
-    state.levelValue = (value==null) ? 100 : value
-    log.trace "setLevel($value)"
-    def cmds = []
-
-    if (value == 0) {
-        sendEvent(name: "switch", value: "off")
-        cmds << "st cmd 0x${device.deviceNetworkId} ${endpointId} 6 0 {}"
-    }
-    else if (device.latestValue("switch") == "off") {
-        sendEvent(name: "switch", value: "on")
-    }
-
-    sendEvent(name: "level", value: state.levelValue)
-    def level = hex(state.levelValue * 254 / 100)
-    cmds << "st cmd 0x${device.deviceNetworkId} ${endpointId} 8 4 {${level} 0000}"
-
-    //log.debug cmds
-    cmds
-}
-
-//Naming based on the wiki article here: http://en.wikipedia.org/wiki/Color_temperature
-private getGenericName(value){
-    def genericName = "White"
-    if(value < 3300){
-        genericName = "Soft White"
-    } else if(value < 4150){
-        genericName = "Moonlight"
-    } else if(value < 5000){
-        genericName = "Cool White"
-    } else if(value <= 6500){
-        genericName = "Daylight"
-    }
-
-    genericName
-}
-
-private getEndpointId() {
-    new BigInteger(device.endpointId, 16).toString()
-}
-
-private hex(value, width=2) {
-    def s = new BigInteger(Math.round(value).toString()).toString(16)
-    while (s.size() < width) {
-        s = "0" + s
-    }
-    s
-}
-
-private String swapEndianHex(String hex) {
-    reverseArray(hex.decodeHex()).encodeHex()
-}
-
-private Integer convertHexToInt(hex) {
-    Integer.parseInt(hex,16)
-}
-
-//Need to reverse array of size 2
-private byte[] reverseArray(byte[] array) {
-    byte tmp;
-    tmp = array[1];
-    array[1] = array[0];
-    array[0] = tmp;
-    return array
-}

devicetypes/smartthings/smartpower-outlet.src/smartpower-outlet.groovy

@@ -143,7 +143,7 @@ def refresh() {
 def configure() {
 	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
-	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+	sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	// OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
 	refresh() + zigbee.onOffConfig(0, 300) + powerConfig()

devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy

@@ -104,7 +104,7 @@ def configure() {
     log.debug "Configuring Reporting and Bindings."
     // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig()

devicetypes/smartthings/zigbee-rgb-bulb.src/zigbee-rgb-bulb.groovy

@@ -28,8 +28,8 @@ metadata {
 		capability "Switch Level"
 		capability "Health Check"
 
-		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Gardenspot RGB"
-		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY Gardenspot RGB"
+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Gardenspot RGB", deviceJoinName: "OSRAM LIGHTIFY Gardenspot mini RGB"
+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY Gardenspot RGB", deviceJoinName: "OSRAM LIGHTIFY Gardenspot mini RGB"
 	}
 
 	// UI tile definitions

devicetypes/smartthings/zigbee-rgbw-bulb.src/zigbee-rgbw-bulb.groovy

@@ -145,7 +145,7 @@ def configure() {
     log.debug "Configuring Reporting and Bindings."
     // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     refresh()

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/zigbee-white-color-temperature-bulb.groovy

@@ -37,7 +37,6 @@ metadata {
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Classic A60 TW", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY A19 Tunable White", deviceJoinName: "OSRAM LIGHTIFY LED Tunable White 60W"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300, 0B04, FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Classic B40 TW - LIGHTIFY", deviceJoinName: "OSRAM LIGHTIFY Classic B40 Tunable White"
-        fingerprint profileId: "0104", deviceId: "0102", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0300", outClusters: "0019", manufacturer: "Eaton", model: "Halo_LT01", deviceJoinName: "Halo_LT01"
     }
 
     // UI tile definitions
@@ -129,7 +128,7 @@ def configure() {
     log.debug "Configuring Reporting and Bindings."
     // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
     // enrolls with default periodic reporting until newer 5 min interval is confirmed
-    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
     refresh()
@@ -155,4 +154,4 @@ def setGenericName(value){
         }
         sendEvent(name: "colorName", value: genericName)
     }
-}
+}

devicetypes/smartthings/zwave-switch-generic.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-switch-generic.src/README.md

@@ -0,0 +1,39 @@
+# Z-wave Switch
+
+
+
+Works with: 
+
+* [Leviton Appliance Module (DZPA1-1LW)](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
+* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave)](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Health Check** - indicates ability to get device health notifications
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+
+## Device Health
+
+A Category C5 Leviton Appliance Module (DZPA1-1LW) and GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Leviton Appliance Module (DZPA1-1LW) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
+* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)

devicetypes/smartthings/zwave-switch-generic.src/zwave-switch-generic.groovy

@@ -14,12 +14,15 @@
 metadata {
 	definition (name: "Z-Wave Switch Generic", namespace: "smartthings", author: "SmartThings") {
 		capability "Actuator"
+		capability "Health Check"
  		capability "Switch"
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
 
 		fingerprint inClusters: "0x25", deviceJoinName: "Z-Wave Switch"
+		fingerprint mfr:"001D", prod:"1A02", deviceJoinName: "Z-Wave Switch"
+		fingerprint mfr:"0063", prod:"4F50", deviceJoinName: "Z-Wave Switch"
 	}
 
 	// simulator metadata
@@ -50,6 +53,11 @@ metadata {
 	}
 }
 
+def updated(){
+// Device-Watch simply pings if no device events received for checkInterval duration of 32min = 2 * 15min + 2min lag time
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description) {
 	def result = null
 	def cmd = zwave.parse(description, [0x20: 1, 0x70: 1])
@@ -126,6 +134,13 @@ def poll() {
 	])
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),

devicetypes/smartthings/zwave-switch.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-switch.src/README.md

@@ -0,0 +1,49 @@
+# Z-Wave Switch
+
+
+Works with: 
+
+* [GE Z-Wave Plug-In Smart Switch (12719)](http://products.z-wavealliance.org/products/1193)
+* [GE Z-Wave In-Wall Smart Outlet (12721)](http://products.z-wavealliance.org/products/1195)
+* [GE Z-Wave In-Wall Smart Switch (12722)](http://products.z-wavealliance.org/products/1196)
+* [GE Z-Wave In-Wall Smart Toggle Switch (12727)](http://products.z-wavealliance.org/products/1200)
+
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#Troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Indicator** - gives you the ability to set the indicator LED light on a Z-Wave switch
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Z-Wave Switches (Plug-In, In-Wall(Toggle Switch, Switch, Outlet)) are polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [General Z-Wave Dimmer/Switch Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200955890-Troubleshooting-GE-in-wall-switch-or-dimmer-won-t-respond-to-commands-or-automations-Z-Wave-)
+* [GE Z-Wave Plug-In Smart Switch (12719) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200903070-GE-Plug-In-Smart-Switch-GE-12719-Z-Wave)
+* [GE Z-Wave In-Wall Smart Outlet (12721) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200903020-GE-In-Wall-Smart-Outlet-GE-12721-Z-Wave)
+* [GE Z-Wave In-Wall Smart Switch (12722) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200902540-GE-In-Wall-Smart-Switch-GE-12722-Z-Wave)
+* [GE Z-Wave In-Wall Smart Toggle Switch (12727) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/207568933-GE-In-Wall-Smart-Toggle-Switch-GE-12727-Z-Wave)
+
+

devicetypes/smartthings/zwave-switch.src/zwave-switch.groovy

@@ -19,6 +19,7 @@ metadata {
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
+		capability "Health Check"
 
 		fingerprint mfr:"0063", prod:"4952", deviceJoinName: "Z-Wave Wall Switch"
 		fingerprint mfr:"0063", prod:"5257", deviceJoinName: "Z-Wave Wall Switch"
@@ -64,6 +65,8 @@ metadata {
 }
 
 def updated(){
+		// Device-Watch simply pings if no device events received for 32min(checkInterval)
+		sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
   switch (ledIndicator) {
         case "on":
             indicatorWhenOn()
@@ -156,6 +159,13 @@ def poll() {
 	])
 }
 
+/**
+  * PING is used by Device-Watch in attempt to reach the Device
+**/
+def ping() {
+		refresh()
+}
+
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),

smartapps/pope/battery-monitor.src/battery-monitor.groovy

@@ -0,0 +1,83 @@
+/**
+ *  Battery Monitor
+ *
+ *  Copyright 2014 Anders Heie
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+definition(
+    name: "Battery Monitor",
+    namespace: "Pope",
+    author: "Anders Heie",
+    description: "Monitors all Battery levels and sends a notification if lower than a set threshold.  A Button allows an immediate check. ",
+    category: "Convenience",
+    iconUrl: "https://s3.amazonaws.com/smartapp-icons/Convenience/Cat-Convenience.png",
+    iconX2Url: "https://s3.amazonaws.com/smartapp-icons/Convenience/Cat-Convenience@2x.png")
+
+
+preferences {
+	section("Battery Settings") {
+		input "threshold", "number", title: "Alert when below...", required: true
+        input "batteries", "capability.battery", title: "Which devices?", multiple: true
+        input "theTime", "time", title: "Time to battery check every day"
+	}
+}
+
+
+
+def installed() {
+	log.debug "Installed with settings: ${settings}"
+	initialize()
+}
+
+def updated() {
+	log.debug "Updated with settings: ${settings}"
+	unschedule()
+	initialize()
+}
+
+def initialize() {
+
+    //schedule the job
+    // http://docs.smartthings.com/en/latest/smartapp-developers-guide/scheduling.html
+    schedule(theTime, doBatteryCheck)
+
+    //run at install too
+    doBatteryCheck()
+
+}
+
+def doBatteryCheck() {
+    log.debug "doBatteryCheck called at ${new Date()}"
+	
+    def belowLevelCntr = 0
+	def pushMsg = ""
+
+	for (batteryDevice in batteries) {
+    	def batteryLevel = batteryDevice.currentValue("battery")
+		log.debug "${batteryDevice.name} '${batteryDevice.label}' battery: ${batteryLevel}% versus alarm at ${settings.threshold}"
+        if ( batteryLevel <= settings.threshold ) {
+            pushMsg += "${batteryDevice.name} '${batteryDevice.label}' battery: ${batteryLevel}% \n"
+            belowLevelCntr++
+        }
+    }
+
+    if (belowLevelCntr ){
+    	pushMsg = "You have ${belowLevelCntr} devices below the set alarm level ${settings.threshold}% \n" + pushMsg
+
+    } else {
+        pushMsg = "Battery Check App executed with no devices below ${settings.threshold}%"
+    }
+
+    log.debug(pushMsg)
+
+    sendPush(pushMsg)
+}

smartapps/smartthings/hue-connect.src/hue-connect.groovy

@@ -37,7 +37,10 @@ preferences {
 
 def mainPage() {
 	def bridges = bridgesDiscovered()
-	if (state.username && bridges) {
+
+	if (state.refreshUsernameNeeded) {
+		return bridgeLinking()
+	} else if (state.username && bridges) {
 		return bulbDiscovery()
 	} else {
 		return bridgeDiscovery()
@@ -102,13 +105,22 @@ def bridgeLinking() {
 
 	def nextPage = ""
 	def title = "Linking with your Hue"
-    def paragraphText
+	def paragraphText
 	if (selectedHue) {
+		if (state.refreshUsernameNeeded) {
+			paragraphText = "The current Hue username is invalid.\n\nPlease press the button on your Hue Bridge to re-link. "
+		} else {
 		paragraphText = "Press the button on your Hue Bridge to setup a link. "
-    } else {
-    	paragraphText = "You haven't selected a Hue Bridge, please Press \"Done\" and select one before clicking next."
-    }
+		}
+	} else {
+		paragraphText = "You haven't selected a Hue Bridge, please Press \"Done\" and select one before clicking next."
+	}
 	if (state.username) { //if discovery worked
+		if (state.refreshUsernameNeeded) {
+			state.refreshUsernameNeeded = false
+			// Issue one poll with new username to cancel local polling with old username
+			poll()
+		}
 		nextPage = "bulbDiscovery"
 		title = "Success!"
 		paragraphText = "Linking to your hub was a success! Please click 'Next'!"
@@ -915,8 +927,15 @@ private handleCommandResponse(body) {
 					updates[childDeviceNetworkId]."$eventType" = v
 				}
 			}
-		} else if (payload.error) {
-			log.warn "Error returned from Hue bridge error = ${body?.error}"
+		} else if (payload?.error) {
+			log.warn "Error returned from Hue bridge, error = ${payload?.error}"
+			// Check for unauthorized user
+			if (payload?.error?.type?.value == 1) {
+				log.error "Hue username is not valid"
+				state.refreshUsernameNeeded = true
+				state.username = null
+			}
+			return []
 		}
 	}