MSA-1875: Originally developed by Don Caruanna with minor changes from Sensative.

This is intended to be the official/default device handler for Strips by Sensative.

The preference defaults are set to the device defaults. 
(If you are looking for accurate values in the IDE, you have to hit "Done" in preferences once, even if you don't change any settings.)

Preferences with an asterisk have to wait for the next wakeup, automatic or manual. The pending icon will display if there are changes pending and say "Synced" otherwise. If you revert your preferences to values that match the device before the next wakeup, it will go back to "Synced". Only changed preferences are pushed to the device.

The actual wakeup by the device is approximately 90% of the wakeupinterval setting. So the observed wakeup interval will be a little less than the chosen one. Also, the wakeupinterval has a minimum of 1800 and a maximum of 86400.

A tamper notification is sent in 2 cases:
Putting a magnet on the round edge when there is a magnet on the square one triggers tamper
During a Manual Wake Up, a tamper is sent before the Node Info.
The tamper event time can be cleared by just tapping on the time itself. Tamper events are reported so they can be seen historically in the GUI.

devicetypes/doncaruana/strips-by-sensative.src/strips-by-sensative.groovy

@@ -0,0 +1,438 @@
+/**
+ *  Strips by Sensative
+ *  Device Handler by Don Caruana
+ *
+ *  Date: 2017-2-19
+ *  Supported Command Classes per device specs
+ *  
+ *         Association v2
+ *         Association Group Information
+ *         Battery
+ *         Binary Sensor
+ *         Configuration
+ *         Device Reset Local
+ *         Manufacturer Specific
+ *         Notification v4
+ *         Powerlevel
+ *         Version v2
+ *         Wake Up v2
+ *         ZWavePlus Info v2
+ *
+ *   Parm Size Description                                   Value
+ *      1    1 Type of report to send                        1 (Default)-Notification Report, 0-Binary Sensor report, 2-Basic report
+ *      2    1 LED Indication                                1 (Default)-On for event (ex. door opened), 0-Off
+ * 
+ *    This device handler will just override the smartthings default wakeup interval of 4 hours and set to 24 hours (manufacturer default)
+ *      and check the battery once a day (no sooner than every 23 hours)
+ */
+
+metadata {
+	definition (name: "Strips by Sensative", namespace: "doncaruana/Sensative", author: "Don Caruana, Sensative") {
+
+	capability "Contact Sensor"
+	capability "Configuration"
+	capability "Battery"
+	capability "Sensor"
+	capability "Refresh"
+		attribute "needUpdate", "string"
+        attribute "tamper" , "string"
+
+	fingerprint mfr:"019A", prod:"0003", model:"0003", deviceJoinName:"Strips by Sensative"
+	fingerprint deviceId:"0x0701", inClusters: "0x5E,0x86,0x72,0x30,0x70,0x71,0x5A,0x85,0x59,0x80,0x84,0x73"
+	fingerprint cc: "0x5E,0x86,0x72,0x30,0x70,0x71,0x5A,0x85,0x59,0x80,0x84,0x73", mfr:"019A", prod:"0003", model:"0003", deviceJoinName:"Strips by Sensative"
+	}
+
+	preferences {
+    	section ("configuration settings") {
+		input(
+			title : "Changes in Settings marked with  *  will not   take effect until the next device Wake Up."
+			,description : null
+			,type : "paragraph")
+		input "sendType", "enum", 
+			title: "* Reporting Type",
+			description: "Notification Report",
+			options:["binary": "Sensor Binary Report", "notification": "Notification Report", "basic": "Basic Report"],
+			defaultValue: "notification",
+			displayDuringSetup: false
+		input "wakeupInterval","enum",
+			title: "* Device Wake Up Interval",
+			description: "24 hours",
+			defaultValue: "86400",
+			required: false,
+			displayDuringSetup: false,
+			options: buildInterval()
+        input "led", "bool", 
+			title: "* LED On",
+			defaultValue: true,
+			displayDuringSetup: false
+		input "ignoreWakeup", "bool", 
+			title: "Ignore Manual Wake Up",
+			defaultValue: false,
+			displayDuringSetup: false
+		input "invertOutput", "bool", 
+			title: "Invert Open/Close Reporting",
+			defaultValue: false,
+			displayDuringSetup: false
+		}
+    }
+
+	tiles(scale: 2) {
+		multiAttributeTile(name:"contact", width: 6, height: 4, canChangeIcon: true){
+			tileAttribute ("device.contact", key: "PRIMARY_CONTROL") {
+				attributeState "open", label:'${name}', icon:"st.contact.contact.open", backgroundColor:"#ffa81e"
+				attributeState "closed", label:'${name}', icon:"st.contact.contact.closed", backgroundColor:"#79b821"
+			}
+		}
+		standardTile("tamper", "device.tamper", inactiveLabel: false, width: 4, height: 3) {
+			state "tamper", label:'${currentValue}', action:"refresh.refresh", backgroundColor:"#FFCC7B"
+		}
+		standardTile("configure", "device.needUpdate", inactiveLabel: false, width: 2, height: 2) {
+			state "NO" , label:'Synced', backgroundColor:"#B1D57D"
+			state "YES", label:'Pending changes', backgroundColor:"#FFCC7B"
+        }
+		standardTile("battery", "device.battery",  inactiveLabel: false, width: 2, height: 1) {
+			state "battery", label:'Battery: ${currentValue}%'
+		}
+
+		main (["contact"])
+		details(["contact","battery","tamper","configure"])
+	}
+
+	simulator {
+		// messages the device returns in response to commands it receives
+		status "open (basic)" : "command: 9881, payload: 00 20 01 FF"
+		status "closed (basic)" : "command: 9881 payload: 00 20 01 00"
+		status "open (notification)" : "command: 9881, payload: 00 71 05 06 FF 00 FF 06 16 00 00"
+		status "closed (notification)" : "command: 9881, payload: 00 71 05 06 00 00 FF 06 17 00 00"
+		status "wake up" : "command: 9881, payload: 00 84 07"
+		status "battery (100%)" : "command: 9881, payload: 00 80 03 64"
+		status "battery low" : "command: 9881, payload: 00 80 03 FF"
+	}
+}
+
+def configure() {
+	def commands = []  
+	state.lastupdate = now()
+	sendEvent(name: "tamper", value: "No Tamper", displayed: false)
+	log.debug "Listing all device parameters and defaults since this is a new inclusion"
+	commands << zwave.manufacturerSpecificV1.manufacturerSpecificGet().format()
+	commands << zwave.versionV1.versionGet().format()
+	commands << zwave.batteryV1.batteryGet().format()
+	commands << zwave.configurationV1.configurationGet(parameterNumber: 1).format()
+	commands << zwave.configurationV1.configurationGet(parameterNumber: 2).format()
+	commands << zwave.wakeUpV2.wakeUpIntervalSet(seconds: 86400, nodeid:zwaveHubNodeId).format()
+	commands << zwave.wakeUpV2.wakeUpIntervalGet().format()
+	commands << zwave.wakeUpV2.wakeUpNoMoreInformation().format()
+	delayBetween(commands, 1500)
+}
+
+private getCommandClassVersions() {
+	[
+		0x71: 3,  // Notification
+		0x5E: 2,  // ZwaveplusInfo
+		0x59: 1,  // AssociationGrpInfo
+		0x85: 2,  // Association
+		0x80: 1,  // Battery
+		0x70: 1,  // Configuration
+		0x5A: 1,  // DeviceResetLocally
+		0x72: 1,  // ManufacturerSpecific
+		0x73: 1,  // Powerlevel
+		0x84: 2,  // WakeUp
+		0x86: 1,  // Version
+		0x30: 1,  // Binary Sensor
+	]
+}
+
+// Parse incoming device messages to generate events
+def parse(String description) {
+	def result = []
+	def cmd
+	if (description.startsWith("Err 106")) {
+		state.sec = 0
+		result = createEvent( name: "secureInclusion", value: "failed", eventType: "ALERT",
+				descriptionText: "This sensor failed to complete the network security key exchange. If you are unable to control it via SmartThings, you must remove it from your network and add it again.")
+	} else if (description.startsWith("Err")) {
+		result = createEvent(descriptionText: "$device.displayName $description", isStateChange: true)
+	} else {
+		cmd = zwave.parse(description, commandClassVersions)
+		if (cmd) {
+			result = zwaveEvent(cmd)
+		}
+	}
+	if (result instanceof List) {
+		result = result.flatten()
+	}
+	log.debug "Parsed '$description' to $result"
+	return result
+}
+
+/**
+* Triggered when Done button is pushed on Preference Pane
+*/
+def updated()
+{
+	if(now() - state.lastupdate > 3000){
+		def isUpdateNeeded = "NO"
+		if(wakeupInterval != null && state.wakeupInterval != wakeupInterval) {isUpdateNeeded = "YES"}
+		if (sendType != null && sendType != state.sendType) {isUpdateNeeded = "YES"}
+		if (led != null && led != state.led) {isUpdateNeeded = "YES"}
+		state.lastupdate = now()
+		sendEvent(name:"needUpdate", value: isUpdateNeeded, displayed:false, isStateChange: true)
+	}
+}
+
+/**
+* Only device parameter changes require a state change 
+*/
+def update_settings()
+{
+	def cmds = []
+	def isUpdateNeeded = "NO"
+	if (state.wakeupInterval != wakeupInterval){
+		cmds << zwave.wakeUpV2.wakeUpIntervalSet(seconds: wakeupInterval.toInteger(), nodeid:zwaveHubNodeId).format()
+		cmds << "delay 1000"
+		cmds << zwave.wakeUpV2.wakeUpIntervalGet().format()
+	}
+	if (sendType != state.sendType){
+		cmds << zwave.configurationV1.configurationSet(parameterNumber: 1, size: 1, configurationValue: [sendType == "binary" ? 0 : sendType == "basic" ? 2 : 1]).format()
+		cmds << "delay 1000"
+		cmds << zwave.configurationV1.configurationGet(parameterNumber: 1).format()
+	}
+	if (led != state.led){
+		cmds << zwave.configurationV1.configurationSet(parameterNumber: 2, size: 1, configurationValue: [led == true ? 1 : 0]).format()
+		cmds << "delay 1000"
+		cmds << zwave.configurationV1.configurationGet(parameterNumber: 2).format()
+	}
+	cmds << "delay 1000"
+	sendEvent(name:"needUpdate", value: isUpdateNeeded, displayed:false, isStateChange: true)
+	return cmds
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.configurationv1.ConfigurationReport cmd) {
+	def name = ""
+	def value = ""
+	def tmpParm = cmd.parameterNumber
+
+	def reportValue = cmd.configurationValue[0]
+	switch (cmd.parameterNumber) {
+		case 1:
+			name = "sendType"
+			switch (reportValue) {
+				case 0:
+					value = "binary"
+					break
+				case 1:
+					value = "notification"
+					break
+				case 2:
+				  value = "basic"
+					break
+						default:
+						break
+			}
+			state.sendType = value
+			log.debug "sendType = $value"
+			break
+		case 2:
+			name = "led"
+			value = reportValue
+			log.debug "led = $value"
+			state.led = reportValue == 1 ? true : false
+			break
+		default:
+			break
+	}
+	sendEvent(name: name, value: value, displayed: true)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.securityv1.SecurityMessageEncapsulation cmd) {
+	def encapsulatedCommand = cmd.encapsulatedCommand(commandClassVersions)
+	log.debug "encapsulated: $encapsulatedCommand"
+	if (encapsulatedCommand) {
+		state.sec = 1
+		return zwaveEvent(encapsulatedCommand)
+	} else {
+		log.warn "Unable to extract encapsulated cmd from $cmd"
+		return [createEvent(descriptionText: cmd.toString())]
+	}
+}
+
+def sensorValueEvent(value) {
+	//If the invertOutput parameter is set, logically invert the output value
+	def flip = 0
+	if (state.sendType == "notification"){
+		flip = value ^ 0x1}
+	else{
+		flip = value ^ 0xFF}
+  if (invertOutput) {value = flip}
+	if (value) {
+		createEvent(name: "contact", value: "open", descriptionText: "$device.displayName is open")
+	} else {
+		createEvent(name: "contact", value: "closed", descriptionText: "$device.displayName is closed")
+	}
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.basicv1.BasicReport cmd) {
+	return sensorValueEvent(cmd.value)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.basicv1.BasicSet cmd) {
+	return sensorValueEvent(cmd.value)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.sensorbinaryv1.SensorBinaryReport cmd) {
+	return sensorValueEvent(cmd.sensorValue)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.sensoralarmv1.SensorAlarmReport cmd) {
+	return sensorValueEvent(cmd.sensorState)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.notificationv3.NotificationReport cmd) {
+	def result = []
+	if (cmd.notificationType == 0x06 && cmd.event == 0x16) {
+		result << sensorValueEvent(1)
+	} else if (cmd.notificationType == 0x06 && cmd.event == 0x17) {
+		result << sensorValueEvent(0)
+	} else if (cmd.notificationType == 0x07) {
+		if (cmd.event == 0x00) {
+			if (cmd.eventParametersLength == 0 || cmd.eventParameter[0] != 3) {
+				result << createEvent(descriptionText: "$device.displayName covering replaced", isStateChange: true, displayed: false)
+			} else {
+				result << sensorValueEvent(0)
+			}
+		} else if (cmd.event == 0x01 || cmd.event == 0x02) {
+			result << sensorValueEvent(1)
+		} else if (cmd.event == 0x03) {
+			result << createEvent(descriptionText: "$device.displayName covering was removed", isStateChange: true)
+			if (!device.currentState("ManufacturerCode")) {
+				result << response(secure(zwave.manufacturerSpecificV1.manufacturerSpecificGet()))
+			}
+		} else if (cmd.event == 0x04) {
+				def timeString1 = new Date().format("MMM d", location.timeZone)
+				def timeString2 = new Date().format("hh:mm:ss", location.timeZone)
+				result << createEvent(name: "tamper", value: "Tampered\n${timeString1}\n${timeString2}", descriptionText: "$device.displayName was tampered with at ${timeString1} ${timeString2}", isStateChange: true)
+				if (!ignoreWakeup) {
+					sendEvent(name:"WakeUp", value: "Manual Wakeup", descriptionText: "${device.displayName} woke up", isStateChange: true, displayed: true)
+					result << doWakeup()
+				}
+		} else if (cmd.event == 0x05 || cmd.event == 0x06) {
+			result << createEvent(descriptionText: "$device.displayName detected glass breakage", isStateChange: true)
+		} else {
+			result << createEvent(descriptionText: "$device.displayName event $cmd.event ${cmd.eventParameter.inspect()}", isStateChange: true, displayed: false)
+		}
+	} else if (cmd.notificationType) {
+			result << createEvent(descriptionText: "$device.displayName notification $cmd.notificationType event $cmd.event ${cmd.eventParameter.inspect()}", isStateChange: true, displayed: false)
+	} else {
+			def value = cmd.v1AlarmLevel == 255 ? "active" : cmd.v1AlarmLevel ?: "inactive"
+			result << createEvent(name: "alarm $cmd.v1AlarmType", value: value, isStateChange: true, displayed: false)
+	}
+	return result
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.wakeupv2.WakeUpNotification cmd) {
+	def event = createEvent(name: "WakeUp", value: "Auto Wakeup", descriptionText: "${device.displayName} woke up", isStateChange: true, displayed: true)
+	def cmds = []
+
+	if (!device.currentState("ManufacturerCode")) {
+		cmds << zwave.manufacturerSpecificV1.manufacturerSpecificGet().format()
+		cmds << "delay 2000"
+	}
+	if (!state.lastbat || now() - state.lastbat > 23*60*60*1000) {  //check no sooner than once every 23 hours (once a day)
+		log.debug "checking battery"
+		event.descriptionText += ", requesting battery"
+		cmds << zwave.batteryV1.batteryGet().format()
+		cmds << "delay 2000"
+	} else {
+		log.debug "not checking battery, was updated ${(now() - state.lastbat)/60000 as int} min ago"
+	}
+	if (device.currentValue("needUpdate") == "YES") { cmds += update_settings() }
+	cmds << zwave.wakeUpV2.wakeUpNoMoreInformation().format()
+	return [event, response(cmds)]
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.batteryv1.BatteryReport cmd) {
+  def map = [ name: "battery", unit: "%" ]
+	if (cmd.batteryLevel == 0xFF) {
+		map.value = 1
+		map.descriptionText = "${device.displayName} has a low battery"
+		map.isStateChange = true
+	} else {
+		map.value = cmd.batteryLevel
+	}
+	def event = createEvent(map)
+	map.isStateChange = true
+	state.lastbat = now()
+	return [event]
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.manufacturerspecificv1.ManufacturerSpecificReport cmd) {
+	def result = []
+	def manufacturerCode = String.format("%04X", cmd.manufacturerId)
+	def productTypeCode = String.format("%04X", cmd.productTypeId)
+	def productCode = String.format("%04X", cmd.productId)
+	def wirelessConfig = "ZWP"
+
+	updateDataValue("Manufacturer", cmd.manufacturerName)
+	updateDataValue("Manufacturer ID", manufacturerCode)
+	updateDataValue("Product Type", productTypeCode)
+	updateDataValue("Product Code", productCode)
+	return result
+}
+
+def zwaveEvent(physicalgraph.zwave.Command cmd) {
+	return [createEvent(descriptionText: "$device.displayName: $cmd", displayed: false)]
+}
+
+private secure(physicalgraph.zwave.Command cmd) {
+	if (state.sec == 0) {  // default to secure
+		cmd.format()
+	} else {
+		zwave.securityV1.securityMessageEncapsulation().encapsulate(cmd).format()
+	}
+}
+
+private secureSequence(commands, delay=200) {
+	delayBetween(commands.collect{ secure(it) }, delay)
+}
+
+def buildInterval() {
+	def intervalList = []
+   	intervalList << [ "0" : "Disabled" ]
+	intervalList << [ "1800" : "30 minutes" ]
+	intervalList << [ "3600" : "1 hour" ]
+	intervalList << [ "7200" : "2 hours" ]
+	intervalList << [ "10800" : "3 hours" ]
+	intervalList << [ "14400" : "4 hours" ]
+	intervalList << [ "18000" : "5 hours" ]
+	intervalList << [ "21600" : "6 hours" ]
+	intervalList << [ "36000" : "10 hours" ]
+	intervalList << [ "43200" : "12 hours" ]
+	intervalList << [ "86400" : "24 hours" ]
+}
+
+def doWakeup() {	
+	def cmds = []
+	cmds << "delay 2000"
+	if (device.currentValue("needUpdate") == "YES") { cmds += update_settings() }
+	cmds << zwave.wakeUpV2.wakeUpNoMoreInformation().format()
+	return response(cmds)
+}
+
+def refresh() {
+ sendEvent(name: "tamper", value: "No Tamper", displayed: false)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.versionv1.VersionReport cmd) {
+	def appversion = String.format("%02d.%02d", cmd.applicationVersion, cmd.applicationSubVersion)
+	def zprotoversion = String.format("%d.%02d", cmd.zWaveProtocolVersion, cmd.zWaveProtocolSubVersion)
+	updateDataValue("zWave Library", cmd.zWaveLibraryType.toString())
+	updateDataValue("Firmware", appversion)
+	updateDataValue("zWave Version", zprotoversion)
+	sendEvent(name: "Firmware", value: appversion, displayed: true)
+}
+
+def zwaveEvent(physicalgraph.zwave.commands.wakeupv2.WakeUpIntervalReport cmd) {
+	state.wakeupInterval = cmd.seconds.toString()
+	sendEvent(name: "wakeupInterval", value: state.wakeupInterval, displayed: true)
+}

devicetypes/fibargroup/fibaro-door-window-sensor-zw5.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/fibargroup/fibaro-door-window-sensor-zw5.src/README.md

@@ -0,0 +1,41 @@
+# Fibaro Door Window Sensor ZW5
+
+Cloud Execution
+
+Works with: 
+
+* [Fibaro Door/Window Sensor ZW5](https://www.smartthings.com/works-with-smartthings/sensors/fibaro-doorwindow-sensor)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Battery** - defines device uses a battery
+* **Contact Sensor** - can detect contact (possible values: open,closed)
+* **Sensor** - detects sensor events
+* **Tamper Alert** - detects tampers
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Fibaro Door/Window Sensor ZW5 is a Z-wave sleepy device and wakes up every 4 hours.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*4*60 + 2)mins = 482 mins.
+
+* __482min__ checkInterval
+
+## Battery Specification
+
+One 1/2AA 3.6V battery is required.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Fibaro Door/Window Sensor ZW5 Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/204075194-Fibaro-Door-Window-Sensor)

devicetypes/fibargroup/fibaro-door-window-sensor-zw5.src/fibaro-door-window-sensor-zw5.groovy

@@ -20,6 +20,7 @@ metadata {
 		capability "Sensor"
         capability "Configuration"
         capability "Tamper Alert"
+		capability "Health Check"
 
         fingerprint deviceId: "0x0701", inClusters: "0x5E, 0x85, 0x59, 0x22, 0x20, 0x80, 0x70, 0x56, 0x5A, 0x7A, 0x72, 0x8E, 0x71, 0x73, 0x98, 0x2B, 0x9C, 0x30, 0x86, 0x84", outClusters: ""
 	}
@@ -199,7 +200,9 @@ def zwaveEvent(physicalgraph.zwave.commands.deviceresetlocallyv1.DeviceResetLoca
 
 def configure() {
 	log.debug "Executing 'configure'"
-    
+	// Device wakes up every 4 hours, this interval allows us to miss one wakeup notification before marking offline
+	sendEvent(name: "checkInterval", value: 8 * 60 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+
     def cmds = []
     
     cmds += zwave.wakeUpV2.wakeUpIntervalSet(seconds:21600, nodeid: zwaveHubNodeId)//FGK's default wake up interval

devicetypes/fibargroup/fibaro-flood-sensor-zw5.src/fibaro-flood-sensor-zw5.groovy

@@ -34,13 +34,13 @@ metadata {
 	tiles(scale: 2) {
 		multiAttributeTile(name:"FGFS", type:"lighting", width:6, height:4) {//with generic type secondary control text is not displayed in Android app
 			tileAttribute("device.water", key:"PRIMARY_CONTROL") {
-				attributeState("dry", icon:"st.alarm.water.dry", backgroundColor:"#00a0dc")
-				attributeState("wet", icon:"st.alarm.water.wet", backgroundColor:"#e86d13")
+				attributeState("dry", icon:"st.alarm.water.dry", backgroundColor:"#ffffff")
+				attributeState("wet", icon:"st.alarm.water.wet", backgroundColor:"#00a0dc")
 			}
 			
 			tileAttribute("device.tamper", key:"SECONDARY_CONTROL") {
-				attributeState("active", label:'tamper active', backgroundColor:"#00a0dc")
-				attributeState("inactive", label:'tamper inactive', backgroundColor:"#cccccc")
+				attributeState("active", label:'tamper active', backgroundColor:"#cccccc")
+				attributeState("inactive", label:'tamper inactive', backgroundColor:"#00A0DC")
 			}
 		}
 		

devicetypes/keen-home/keen-home-smart-vent.src/keen-home-smart-vent.groovy

@@ -22,7 +22,6 @@ metadata {
         command "clearObstruction"
 
         fingerprint endpoint: "1", profileId: "0104", inClusters: "0000,0001,0003,0004,0005,0006,0008,0020,0402,0403,0B05,FC01,FC02", outClusters: "0019"
-        fingerprint endpoint: "1", profileId: "0104", inClusters: "0000,0001,0003,0004,0005,0006,0008,0020,0402,0403,0B05,FC01,FC02", outClusters: "0019", manufacturer: "Keen Home Inc", model: "SV01-410-DV-1.0", deviceJoinName: "Keen Home Smart Vent"
     }
 
     // simulator metadata

devicetypes/smartthings/dimmer-switch.src/dimmer-switch.groovy

@@ -12,7 +12,7 @@
  *
  */
 metadata {
-	definition (name: "Dimmer Switch", namespace: "smartthings", author: "SmartThings") {
+	definition (name: "Dimmer Switch", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.switch") {
 		capability "Switch Level"
 		capability "Actuator"
 		capability "Indicator"

devicetypes/smartthings/ecobee-thermostat.src/ecobee-thermostat.groovy

@@ -32,7 +32,7 @@ metadata {
 		command "switchMode"
 		command "switchFanMode"
 
-		attribute "thermostatSetpoint", "number"
+		attribute "displayThermostatSetpoint", "string" // Added to be able to show "Auto"/"Off" keeping attribute thermostatSetpoint a number
 		attribute "thermostatStatus", "string"
 		attribute "maxHeatingSetpoint", "number"
 		attribute "minHeatingSetpoint", "number"
@@ -43,8 +43,8 @@ metadata {
 	}
 
 	tiles {
-		valueTile("temperature", "device.temperature", width: 2, height: 2) {
-			state("temperature", label:'${currentValue}°', unit:"F",
+		standardTile("temperature", "device.temperature", width: 2, height: 2, decoration: "flat") {
+			state("temperature", label:'${currentValue}°', unit:"F", icon: "st.thermostat.ac.air-conditioning",
 					backgroundColors:[
 							// Celsius
 							[value: 0, color: "#153591"],
@@ -70,7 +70,7 @@ metadata {
 			state "heat", action:"switchMode",  nextState: "updating", icon: "st.thermostat.heat"
 			state "cool", action:"switchMode",  nextState: "updating", icon: "st.thermostat.cool"
 			state "auto", action:"switchMode",  nextState: "updating", icon: "st.thermostat.auto"
-			state "auxHeatOnly", action:"switchMode", icon: "st.thermostat.emergency-heat"
+			state "emergency heat", action:"switchMode", icon: "st.thermostat.emergency-heat" // emergency heat = auxHeatOnly
 			state "updating", label:"Working", icon: "st.secondary.secondary"
 		}
 		standardTile("fanMode", "device.thermostatFanMode", inactiveLabel: false, decoration: "flat") {
@@ -81,8 +81,8 @@ metadata {
 		standardTile("upButtonControl", "device.thermostatSetpoint", inactiveLabel: false, decoration: "flat") {
 			state "setpoint", action:"raiseSetpoint", icon:"st.thermostat.thermostat-up"
 		}
-		valueTile("thermostatSetpoint", "device.thermostatSetpoint", width: 1, height: 1, decoration: "flat") {
-			state "thermostatSetpoint", label:'${currentValue}'
+		valueTile("displayThermostatSetpoint", "device.displayThermostatSetpoint", width: 1, height: 1, decoration: "flat") {
+			state "displayThermostatSetpoint", label:'${currentValue}'
 		}
 		valueTile("currentStatus", "device.thermostatStatus", height: 1, width: 2, decoration: "flat") {
 			state "thermostatStatus", label:'${currentValue}', backgroundColor:"#ffffff"
@@ -113,7 +113,7 @@ metadata {
 			state "humidity", label:'${currentValue}%'
 		}
 		main "temperature"
-		details(["temperature", "upButtonControl", "thermostatSetpoint", "currentStatus", "downButtonControl", "mode", "fanMode","humidity", "resumeProgram", "refresh"])
+		details(["temperature", "upButtonControl", "displayThermostatSetpoint", "currentStatus", "downButtonControl", "mode", "fanMode","humidity", "resumeProgram", "refresh"])
 	}
 
 	preferences {
@@ -185,6 +185,11 @@ def generateEvent(Map results) {
 				isChange = isStateChange(device, name, value.toString())
 				event['isStateChange'] = isChange
 				event['displayed'] = false
+			} else if (name == "thermostatMode") {
+				def mode = value.toString()
+				mode = (mode == "auxHeatOnly") ? "emergency heat" : mode
+				isChange = isStateChange(device, name, mode)
+				event << [value: mode, isStateChange: isChange, displayed: isDisplayed]
 			} else {
 				isChange = isStateChange(device, name, value.toString())
 				isDisplayed = isChange
@@ -452,10 +457,10 @@ def emergencyHeat() {
 }
 
 def auxHeatOnly() {
-	log.debug "auxHeatOnly"
+	log.debug "auxHeatOnly = emergency heat"
 	def deviceId = device.deviceNetworkId.split(/\./).last()
 	if (parent.setMode ("auxHeatOnly", deviceId))
-		generateModeEvent("auxHeatOnly")
+		generateModeEvent("emergency heat") // emergency heat = auxHeatOnly
 	else {
 		log.debug "Error setting new mode."
 		def currentMode = device.currentState("thermostatMode")?.value
@@ -574,17 +579,23 @@ def generateSetpointEvent() {
 	sendEvent("name":"heatingSetpoint", "value":heatingSetpoint, "unit":location.temperatureScale)
 	sendEvent("name":"coolingSetpoint", "value":coolingSetpoint, "unit":location.temperatureScale)
 
+	def averageSetpoint = roundC((heatingSetpoint + coolingSetpoint) / 2)
 	if (mode == "heat") {
 		sendEvent("name":"thermostatSetpoint", "value":heatingSetpoint, "unit":location.temperatureScale)
+		sendEvent("name":"displayThermostatSetpoint", "value":heatingSetpoint, "unit":location.temperatureScale, displayed: false)
 	}
 	else if (mode == "cool") {
 		sendEvent("name":"thermostatSetpoint", "value":coolingSetpoint, "unit":location.temperatureScale)
+		sendEvent("name":"displayThermostatSetpoint", "value":coolingSetpoint, "unit":location.temperatureScale, displayed: false)
 	} else if (mode == "auto") {
-		sendEvent("name":"thermostatSetpoint", "value":"Auto")
+		sendEvent("name":"thermostatSetpoint", "value":averageSetpoint, "unit":location.temperatureScale)
+		sendEvent("name":"displayThermostatSetpoint", "value":"Auto", displayed: false)
 	} else if (mode == "off") {
-		sendEvent("name":"thermostatSetpoint", "value":"Off")
-	} else if (mode == "auxHeatOnly") {
+		sendEvent("name":"thermostatSetpoint", "value":averageSetpoint, "unit":location.temperatureScale)
+		sendEvent("name":"displayThermostatSetpoint", "value":"Off", displayed: false)
+	} else if (mode == "emergency heat") { // emergency heat = auxHeatOnly
 		sendEvent("name":"thermostatSetpoint", "value":heatingSetpoint, "unit":location.temperatureScale)
+		sendEvent("name":"displayThermostatSetpoint", "value":heatingSetpoint, "unit":location.temperatureScale, displayed: false)
 	}
 }
 
@@ -621,13 +632,14 @@ void raiseSetpoint() {
 		targetvalue = thermostatSetpoint ? thermostatSetpoint : 0
 		targetvalue = location.temperatureScale == "F"? targetvalue + 1 : targetvalue + 0.5
 
-		if ((mode == "heat" || mode == "auxHeatOnly") && targetvalue > maxHeatingSetpoint) {
+		if ((mode == "heat" || mode == "emergency heat") && targetvalue > maxHeatingSetpoint) { // emergency heat = auxHeatOnly
 			targetvalue = maxHeatingSetpoint
 		} else if (mode == "cool" && targetvalue > maxCoolingSetpoint) {
 			targetvalue = maxCoolingSetpoint
 		}
 
 		sendEvent("name":"thermostatSetpoint", "value":targetvalue, "unit":location.temperatureScale, displayed: false)
+		sendEvent("name":"displayThermostatSetpoint", "value":targetvalue, "unit":location.temperatureScale, displayed: false)
 		log.info "In mode $mode raiseSetpoint() to $targetvalue"
 
 		runIn(3, "alterSetpoint", [data: [value:targetvalue], overwrite: true]) //when user click button this runIn will be overwrite
@@ -666,13 +678,14 @@ void lowerSetpoint() {
 		targetvalue = thermostatSetpoint ? thermostatSetpoint : 0
 		targetvalue = location.temperatureScale == "F"? targetvalue - 1 : targetvalue - 0.5
 
-		if ((mode == "heat" || mode == "auxHeatOnly") && targetvalue < minHeatingSetpoint) {
+		if ((mode == "heat" || mode == "emergency heat") && targetvalue < minHeatingSetpoint) { // emergency heat = auxHeatOnly
 			targetvalue = minHeatingSetpoint
 		} else if (mode == "cool" && targetvalue < minCoolingSetpoint) {
 			targetvalue = minCoolingSetpoint
 		}
 
 		sendEvent("name":"thermostatSetpoint", "value":targetvalue, "unit":location.temperatureScale, displayed: false)
+		sendEvent("name":"displayThermostatSetpoint", "value":targetvalue, "unit":location.temperatureScale, displayed: false)
 		log.info "In mode $mode lowerSetpoint() to $targetvalue"
 
 		runIn(3, "alterSetpoint", [data: [value:targetvalue], overwrite: true]) //when user click button this runIn will be overwrite
@@ -706,7 +719,7 @@ void alterSetpoint(temp) {
 		}
 
 		//step1: check thermostatMode, enforce limits before sending request to cloud
-		if (mode == "heat" || mode == "auxHeatOnly"){
+		if (mode == "heat" || mode == "emergency heat"){ // emergency heat = auxHeatOnly
 			if (temp.value > coolingSetpoint){
 				targetHeatingSetpoint = temp.value
 				targetCoolingSetpoint = temp.value
@@ -735,15 +748,18 @@ void alterSetpoint(temp) {
 
 		if (parent.setHold(heatingValue, coolingValue, deviceId, sendHoldType)) {
 			sendEvent("name": "thermostatSetpoint", "value": temp.value, displayed: false)
+			sendEvent("name": "displayThermostatSetpoint", "value": temp.value, displayed: false)
 			sendEvent("name": "heatingSetpoint", "value": targetHeatingSetpoint, "unit": location.temperatureScale)
 			sendEvent("name": "coolingSetpoint", "value": targetCoolingSetpoint, "unit": location.temperatureScale)
 			log.debug "alterSetpoint in mode $mode succeed change setpoint to= ${temp.value}"
 		} else {
 			log.error "Error alterSetpoint()"
-			if (mode == "heat" || mode == "auxHeatOnly"){
+			if (mode == "heat" || mode == "emergency heat"){ // emergency heat = auxHeatOnly
 				sendEvent("name": "thermostatSetpoint", "value": heatingSetpoint.toString(), displayed: false)
+				sendEvent("name": "displayThermostatSetpoint", "value": heatingSetpoint.toString(), displayed: false)
 			} else if (mode == "cool") {
 				sendEvent("name": "thermostatSetpoint", "value": coolingSetpoint.toString(), displayed: false)
+				sendEvent("name": "displayThermostatSetpoint", "value": heatingSetpoint.toString(), displayed: false)
 			}
 		}
 
@@ -759,6 +775,7 @@ def generateStatusEvent() {
 	def coolingSetpoint = device.currentValue("coolingSetpoint")
 	def temperature = device.currentValue("temperature")
 	def statusText
+	def operatingState = "idle"
 
 	log.debug "Generate Status Event for Mode = ${mode}"
 	log.debug "Temperature = ${temperature}"
@@ -767,20 +784,29 @@ def generateStatusEvent() {
 	log.debug "HVAC Mode = ${mode}"
 
 	if (mode == "heat") {
-		if (temperature >= heatingSetpoint)
+		if (temperature >= heatingSetpoint) {
 			statusText = "Right Now: Idle"
-		else
+		} else {
 			statusText = "Heating to ${heatingSetpoint} ${location.temperatureScale}"
+			operatingState = "heating"
+		}
 	} else if (mode == "cool") {
-		if (temperature <= coolingSetpoint)
+		if (temperature <= coolingSetpoint) {
 			statusText = "Right Now: Idle"
-		else
+		} else {
 			statusText = "Cooling to ${coolingSetpoint} ${location.temperatureScale}"
+			operatingState = "cooling"
+		}
 	} else if (mode == "auto") {
 		statusText = "Right Now: Auto"
+		if (temperature < heatingSetpoint) {
+			operatingState = "heating"
+		} else if (temperature > coolingSetpoint) {
+			operatingState = "cooling"
+		}
 	} else if (mode == "off") {
 		statusText = "Right Now: Off"
-	} else if (mode == "auxHeatOnly") {
+	} else if (mode == "emergency heat") { // emergency heat = auxHeatOnly
 		statusText = "Emergency Heat"
 	} else {
 		statusText = "?"
@@ -788,6 +814,7 @@ def generateStatusEvent() {
 
 	log.debug "Generate Status Event = ${statusText}"
 	sendEvent("name":"thermostatStatus", "value":statusText, "description":statusText, displayed: true)
+	sendEvent("name":"thermostatOperatingState", "value":operatingState, "description":operatingState, displayed: false)
 }
 
 def generateActivityFeedsEvent(notificationMessage) {

devicetypes/smartthings/everspring-flood-sensor.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/everspring-flood-sensor.src/README.md

@@ -0,0 +1,40 @@
+# Everspring Flood Sensor
+
+Cloud Execution
+
+Works with: 
+
+* [Everspring Water Detector](https://www.smartthings.com/works-with-smartthings/sensors/everspring-water-detector)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Water Sensor** - can detect presence of water (dry or wet)
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Sensor** - detects sensor events
+* **Battery** - defines device uses a battery
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Everspring Water Detector is a Z-wave sleepy device and wakes up every 4 hours.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*4*60 + 2)mins = 482 mins.
+
+* __482min__ checkInterval
+
+## Battery Specification
+
+Three AA 1.5V batteries are required.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Everspring Water Detector Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/202088304-Everspring-Water-Detector)

devicetypes/smartthings/everspring-flood-sensor.src/everspring-flood-sensor.groovy

@@ -17,6 +17,7 @@ metadata {
 		capability "Configuration"
 		capability "Sensor"
 		capability "Battery"
+		capability "Health Check"
 
 		fingerprint deviceId: "0xA102", inClusters: "0x86,0x72,0x85,0x84,0x80,0x70,0x9C,0x20,0x71"
 	}
@@ -138,6 +139,8 @@ def zwaveEvent(physicalgraph.zwave.Command cmd)
 
 def configure()
 {
+	// Device wakes up every 4 hours, this interval allows us to miss one wakeup notification before marking offline
+	sendEvent(name: "checkInterval", value: 8 * 60 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
 	if (!device.currentState("battery")) {
 		sendEvent(name: "battery", value:100, unit:"%", descriptionText:"(Default battery event)", displayed:false)
 	}

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy

@@ -135,10 +135,7 @@ def refresh() {
 	return zigbee.readAttribute(0xFC45, 0x0000, ["mfgCode": 0x104E]) +   // New firmware
 			zigbee.readAttribute(0xFC45, 0x0000, ["mfgCode": 0xC2DF]) +   // Original firmware
 			zigbee.readAttribute(zigbee.TEMPERATURE_MEASUREMENT_CLUSTER, 0x0000) +
-			zigbee.readAttribute(zigbee.POWER_CONFIGURATION_CLUSTER, 0x0020) +
-			zigbee.configureReporting(0xFC45, 0x0000, DataType.INT16, 30, 3600, 100) +
-			zigbee.batteryConfig() +
-			zigbee.temperatureConfig(30, 300)
+			zigbee.readAttribute(zigbee.POWER_CONFIGURATION_CLUSTER, 0x0020)
 }
 
 def configure() {
@@ -150,5 +147,10 @@ def configure() {
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	return refresh()
+	return refresh() +
+			zigbee.configureReporting(0xFC45, 0x0000, DataType.UINT16, 30, 3600, 100, ["mfgCode": 0x104E]) +   // New firmware
+			zigbee.configureReporting(0xFC45, 0x0000, DataType.UINT16, 30, 3600, 100, ["mfgCode": 0xC2DF]) +   // Original firmware
+			zigbee.batteryConfig() +
+			zigbee.temperatureConfig(30, 300)
+
 }

devicetypes/smartthings/testing/simulated-refrigerator-door.src/simulated-refrigerator-door.groovy

@@ -0,0 +1,57 @@
+/**
+ *  Copyright 2017 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+metadata {
+	definition (name: "Simulated Refrigerator Door", namespace: "smartthings/testing", author: "SmartThings") {
+		capability "Contact Sensor"
+		capability "Sensor"
+
+		command "open"
+		command "close"
+	}
+
+	tiles {
+		standardTile("contact", "device.contact", width: 2, height: 2) {
+			state("closed", label:'${name}', icon:"st.contact.contact.closed", backgroundColor:"#79b821", action: "open")
+			state("open", label:'${name}', icon:"st.contact.contact.open", backgroundColor:"#ffa81e", action: "close")
+		}
+		standardTile("freezerDoor", "device.contact", width: 2, height: 2, decoration: "flat") {
+			state("closed", label:'Freezer', icon:"st.contact.contact.closed", backgroundColor:"#79b821")
+			state("open", label:'Freezer', icon:"st.contact.contact.open", backgroundColor:"#ffa81e")
+		}
+		standardTile("mainDoor", "device.contact", width: 2, height: 2, decoration: "flat") {
+			state("closed", label:'Fridge', icon:"st.contact.contact.closed", backgroundColor:"#79b821")
+			state("open", label:'Fridge', icon:"st.contact.contact.open", backgroundColor:"#ffa81e")
+		}
+		standardTile("control", "device.contact", width: 1, height: 1, decoration: "flat") {
+			state("closed", label:'${name}', icon:"st.contact.contact.closed", action: "open")
+			state("open", label:'${name}', icon:"st.contact.contact.open", action: "close")
+		}
+		main "contact"
+		details "contact"
+	}
+}
+
+def installed() {
+	sendEvent(name: "contact", value: "closed")
+}
+
+def open() {
+	sendEvent(name: "contact", value: "open")
+	parent.doorOpen(device.deviceNetworkId)
+}
+
+def close() {
+	sendEvent(name: "contact", value: "closed")
+	parent.doorClosed(device.deviceNetworkId)
+}

devicetypes/smartthings/testing/simulated-refrigerator-temperature-control.src/simulated-refrigerator-temperature-control.groovy

@@ -0,0 +1,94 @@
+/**
+ *  Simulated Refrigerator Temperature Control
+ *
+ *  Copyright 2017 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+metadata {
+	definition (name: "Simulated Refrigerator Temperature Control", namespace: "smartthings/testing", author: "SmartThings") {
+		capability "Temperature Measurement"
+		capability "Thermostat Cooling Setpoint"
+
+		command "tempUp"
+		command "tempDown"
+		command "setpointUp"
+		command "setpointDown"
+	}
+
+	tiles {
+		valueTile("refrigerator", "device.temperature", width: 2, height: 2, canChangeBackground: true) {
+			state("temperature", label:'${currentValue}°', unit:"F",
+					backgroundColors:[
+							[value: 0, color: "#153591"],
+							[value: 40, color: "#1e9cbb"],
+							[value: 45, color: "#f1d801"]
+					]
+			)
+		}
+		valueTile("freezer", "device.temperature", width: 2, height: 2, canChangeBackground: true) {
+			state("temperature", label:'${currentValue}°', unit:"F",
+					backgroundColors:[
+							[value: 0, color: "#153591"],
+							[value: 5, color: "#1e9cbb"],
+							[value: 15, color: "#f1d801"]
+					]
+			)
+		}
+		valueTile("freezerSetpoint", "device.coolingSetpoint", inactiveLabel: false, decoration: "flat") {
+			state "setpoint", label:'Freezer Set: ${currentValue}°', unit:"F"
+		}
+		valueTile("refrigeratorSetpoint", "device.coolingSetpoint", inactiveLabel: false, decoration: "flat") {
+			state "heat", label:'Fridge Set: ${currentValue}°', unit:"F"
+		}
+		standardTile("tempUp", "device.temperature", inactiveLabel: false, decoration: "flat") {
+			state "default", action:"tempUp", icon:"st.thermostat.thermostat-up"
+		}
+		standardTile("tempDown", "device.temperature", inactiveLabel: false, decoration: "flat") {
+			state "default", action:"tempDown", icon:"st.thermostat.thermostat-down"
+		}
+		standardTile("setpointUp", "device.coolingSetpoint", inactiveLabel: false, decoration: "flat") {
+			state "default", action:"setpointUp", icon:"st.thermostat.thermostat-up"
+		}
+		standardTile("setpointDown", "device.coolingSetpoint", inactiveLabel: false, decoration: "flat") {
+			state "default", action:"setpointDown", icon:"st.thermostat.thermostat-down"
+		}
+	}
+}
+
+def installed() {
+	sendEvent(name: "temperature", value: device.componentName == "freezer" ? 2 : 40)
+	sendEvent(name: "coolingSetpoint", value: device.componentName == "freezer" ? 2 : 40)
+}
+
+def updated() {
+	installed()
+}
+
+void tempUp() {
+	def value = device.currentValue("temperature") as Integer
+	sendEvent(name: "temperature", value: value + 1)
+}
+
+void tempDown() {
+	def value = device.currentValue("temperature") as Integer
+	sendEvent(name: "temperature", value: value - 1)
+}
+
+void setpointUp() {
+	def value = device.currentValue("coolingSetpoint") as Integer
+	sendEvent(name: "coolingSetpoint", value: value + 1)
+}
+
+void setpointDown() {
+	def value = device.currentValue("coolingSetpoint") as Integer
+	sendEvent(name: "coolingSetpoint", value: value - 1)
+}

devicetypes/smartthings/testing/simulated-refrigerator.src/simulated-refrigerator.groovy

@@ -0,0 +1,91 @@
+/**
+ *  Simulated Refrigerator
+ *
+ *  Example composite device handler that simulates a refrigerator with a freezer compartment and a main compartment.
+ *  Each of these compartments has its own door, temperature, and temperature setpoint. Each compartment modeled
+ *  as a child device of the main refrigerator device so that temperature-based SmartApps can be used with each
+ *  compartment
+ *
+ *  Copyright 2017 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+metadata {
+	definition (name: "Simulated Refrigerator", namespace: "smartthings/testing", author: "SmartThings") {
+		capability "Contact Sensor"
+	}
+
+	tiles(scale: 2) {
+		standardTile("contact", "device.contact", width: 4, height: 4) {
+			state("closed", label:'${name}', icon:"st.fridge.fridge-closed", backgroundColor:"#79b821")
+			state("open", label:'${name}', icon:"st.fridge.fridge-open", backgroundColor:"#ffa81e")
+		}
+		childDeviceTile("freezerDoor", "freezerDoor", height: 2, width: 2, childTileName: "freezerDoor")
+		childDeviceTile("mainDoor", "mainDoor", height: 2, width: 2, childTileName: "mainDoor")
+		childDeviceTile("freezer", "freezer", height: 2, width: 2, childTileName: "freezer")
+		childDeviceTile("refrigerator", "refrigerator", height: 2, width: 2, childTileName: "refrigerator")
+		childDeviceTile("freezerSetpoint", "freezer", height: 1, width: 2, childTileName: "freezerSetpoint")
+		childDeviceTile("refrigeratorSetpoint", "refrigerator", height: 1, width: 2, childTileName: "refrigeratorSetpoint")
+
+		// for simulator
+		childDeviceTile("freezerUp", "freezer", height: 1, width: 1, childTileName: "tempUp")
+		childDeviceTile("freezerDown", "freezer", height: 1, width: 1, childTileName: "tempDown")
+		childDeviceTile("refrigeratorUp", "refrigerator", height: 1, width: 1, childTileName: "tempUp")
+		childDeviceTile("refrigeratorDown", "refrigerator", height: 1, width: 1, childTileName: "tempDown")
+		childDeviceTile("freezerDoorControl", "freezerDoor", height: 1, width: 1, childTileName: "control")
+		childDeviceTile("mainDoorControl", "mainDoor", height: 1, width: 1, childTileName: "control")
+		childDeviceTile("freezerSetpointUp", "freezer", height: 1, width: 1, childTileName: "setpointUp")
+		childDeviceTile("freezerSetpointDown", "freezer", height: 1, width: 1, childTileName: "setpointDown")
+		childDeviceTile("refrigeratorSetpointUp", "refrigerator", height: 1, width: 1, childTileName: "setpointUp")
+		childDeviceTile("refrigeratorSetpointDown", "refrigerator", height: 1, width: 1, childTileName: "setpointDown")
+	}
+}
+
+def installed() {
+	state.counter = state.counter ? state.counter + 1 : 1
+	if (state.counter == 1) {
+		addChildDevice(
+				"Simulated Refrigerator Door",
+				"${device.deviceNetworkId}.1",
+				null,
+				[completedSetup: true, label: "${device.label} (Freezer Door)", componentName: "freezerDoor", componentLabel: "Freezer Door"])
+
+		addChildDevice(
+				"Simulated Refrigerator Door",
+				"${device.deviceNetworkId}.2",
+				null,
+				[completedSetup: true, label: "${device.label} (Main Door)", componentName: "mainDoor", componentLabel: "Main Door"])
+
+		addChildDevice(
+				"Simulated Refrigerator Temperature Control",
+				"${device.deviceNetworkId}.3",
+				null,
+				[completedSetup: true, label: "${device.label} (Freezer)", componentName: "freezer", componentLabel: "Freezer"])
+
+		addChildDevice(
+				"Simulated Refrigerator Temperature Control",
+				"${device.deviceNetworkId}.3",
+				null,
+				[completedSetup: true, label: "${device.label} (Fridge)", componentName: "refrigerator", componentLabel: "Fridge"])
+	}
+}
+
+def doorOpen(dni) {
+	// If any door opens, then the refrigerator is considered to be open
+	sendEvent(name: "contact", value: "open")
+}
+
+def doorClosed(dni) {
+	// Both doors must be closed for the refrigerator to be considered closed
+	if (!childDevices.find{it.deviceNetworkId != dni && it.currentValue("contact") == "open"}) {
+		sendEvent(name: "contact", value: "closed")
+	}
+}

devicetypes/smartthings/wattvision.src/wattvision.groovy

@@ -20,6 +20,7 @@ metadata {
 	definition(name: "Wattvision", namespace: "smartthings", author: "Steve Vlaminck") {
 		capability "Power Meter"
 		capability "Refresh"
+		capability "Sensor"
 		attribute "powerContent", "string"
 	}
 

devicetypes/smartthings/wemo-light-switch.src/wemo-light-switch.groovy

@@ -18,7 +18,7 @@
 
 
 metadata {
-	definition (name: "Wemo Light Switch", namespace: "smartthings", author: "SmartThings") {
+	definition (name: "Wemo Light Switch", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.switch") {
 		capability "Actuator"
 		capability "Switch"
 		capability "Polling"

devicetypes/smartthings/wemo-switch.src/wemo-switch.groovy

@@ -16,7 +16,7 @@
  * Date: 2015-10-11
  */
  metadata {
- 	definition (name: "Wemo Switch", namespace: "smartthings", author: "SmartThings") {
+ 	definition (name: "Wemo Switch", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.smartplug") {
         capability "Actuator"
         capability "Switch"
         capability "Polling"

devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy

@@ -13,7 +13,7 @@
  */
 
 metadata {
-    definition (name: "ZigBee Dimmer", namespace: "smartthings", author: "SmartThings") {
+    definition (name: "ZigBee Dimmer", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.switch") {
         capability "Actuator"
         capability "Configuration"
         capability "Refresh"

devicetypes/smartthings/zigbee-lock.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zigbee-lock.src/README.md

@@ -0,0 +1,46 @@
+# Zigbee Lock
+
+Cloud Execution
+
+Works with: 
+
+* [Yale Push Button Deadbolt (YRD210-HA)](https://www.smartthings.com/works-with-smartthings/door-locks/yale-push-button-deadbolt-yrd210)
+* [Yale Touchscreen Lever (YRL220-ZB)](https://www.smartthings.com/works-with-smartthings/door-locks/yale-touchscreen-lever-yrl220)
+* [Yale Touchscreen Deadbolt (YRD220-HA))](https://www.smartthings.com/works-with-smartthings/door-locks/yale-touchscreen-deadbolt-yrd220)
+* [Yale Key Free Touchscreen Deadbolt (YRD240-HA)](https://www.smartthings.com/works-with-smartthings/door-locks/yale-key-free-touchscreen-deadbolt-yrd240)
+* [Yale Push Button Lever Lock (YRL210-HA)](https://www.smartthings.com/works-with-smartthings/door-locks/yale-push-button-lever-lock-yrl210)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Lock** - allows for the control of a lock device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+* **Battery** - defines device uses a battery
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Yale Push Button Deadbolt (YRD210-HA) is a Zigbee device and checks in every 1 hour.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*60 + 2)mins = 122 mins.
+
+ * __122min__ checkInterval
+
+## Battery Specification
+
+Four AA 1.5V batteries are required.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the sensor from SmartThings can be found in the following link:
+* [Yale Locks Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/205138400)

devicetypes/smartthings/zigbee-lock.src/zigbee-lock.groovy

@@ -24,6 +24,7 @@ import physicalgraph.zigbee.zcl.DataType
         capability "Sensor"
         capability "Battery"
         capability "Configuration"
+        capability "Health Check"
 
         fingerprint profileId: "0104", inClusters: "0000,0001,0003,0004,0005,0009,0020,0101,0402,0B05,FDBD", outClusters: "000A,0019", manufacturer: "Kwikset", model: "SMARTCODE_DEADBOLT_5", deviceJoinName: "Kwikset 5-Button Deadbolt"
         fingerprint profileId: "0104", inClusters: "0000,0001,0003,0004,0005,0009,0020,0101,0402,0B05,FDBD", outClusters: "000A,0019", manufacturer: "Kwikset", model: "SMARTCODE_LEVER_5", deviceJoinName: "Kwikset 5-Button Lever"
@@ -83,6 +84,9 @@ def uninstalled() {
 }
 
 def configure() {
+    // Device-Watch allows 2 check-in misses from device + ping (plus 2 min lag time)
+    sendEvent(name: "checkInterval", value: 2 * 60 * 60 + 2 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+
     def cmds =
         zigbee.configureReporting(CLUSTER_DOORLOCK, DOORLOCK_ATTR_LOCKSTATE,
                                   DataType.ENUM8, 0, 3600, null) +
@@ -92,6 +96,13 @@ def configure() {
     return refresh() + cmds // send refresh cmds as part of config
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+    zigbee.readAttribute(CLUSTER_DOORLOCK, DOORLOCK_ATTR_LOCKSTATE)
+}
+
 def refresh() {
     def cmds =
         zigbee.readAttribute(CLUSTER_DOORLOCK, DOORLOCK_ATTR_LOCKSTATE) +

devicetypes/smartthings/zooz-power-strip.src/zooz-power-strip.groovy

@@ -25,6 +25,7 @@ metadata {
 		capability "Refresh"
 		capability "Actuator"
 		capability "Sensor"
+		capability "Configuration"
 
 		fingerprint manufacturer: "015D", prod: "0651", model: "F51C", deviceJoinName: "Zooz ZEN 20 Power Strip"
 	}
@@ -65,6 +66,10 @@ def updated() {
 	}
 }
 
+def configure() {
+	refresh()
+}
+
 
 //////////////////////
 // Event Generation //
@@ -107,15 +112,17 @@ def zwaveBinaryEvent(cmd, endpoint) {
 	def result = []
 	def children = childDevices
 	def childDevice = children.find{it.deviceNetworkId.endsWith("$endpoint")}
-	childDevice.sendEvent(name: "switch", value: cmd.value ? "on" : "off")
+	if (childDevice) {
+		childDevice.sendEvent(name: "switch", value: cmd.value ? "on" : "off")
 
-	if (cmd.value) {
-		// One on and the strip is on
-		result << createEvent(name: "switch", value: "on")
-	} else {
-		// All off and the strip is off
-		if (! children.any { it.currentValue("switch") == "on" }) {
-			result  << createEvent(name: "switch", value: "off")
+		if (cmd.value) {
+			// One on and the strip is on
+			result << createEvent(name: "switch", value: "on")
+		} else {
+			// All off and the strip is off
+			if (!children.any { it.currentValue("switch") == "on" }) {
+				result << createEvent(name: "switch", value: "off")
+			}
 		}
 	}
 	result

devicetypes/smartthings/zwave-dimmer-switch-generic.src/zwave-dimmer-switch-generic.groovy

@@ -12,7 +12,7 @@
  *
  */
 metadata {
-	definition (name: "Z-Wave Dimmer Switch Generic", namespace: "smartthings", author: "SmartThings") {
+	definition (name: "Z-Wave Dimmer Switch Generic", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.switch") {
 		capability "Switch Level"
 		capability "Actuator"
 		capability "Health Check"

devicetypes/smartthings/zwave-metering-dimmer.src/zwave-metering-dimmer.groovy

@@ -16,7 +16,7 @@
  *
  */
 metadata {
-	definition (name: "Z-Wave Metering Dimmer", namespace: "smartthings", author: "SmartThings") {
+	definition (name: "Z-Wave Metering Dimmer", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.switch") {
 		capability "Switch"
 		capability "Polling"
 		capability "Power Meter"

devicetypes/smartthings/zwave-metering-switch.src/zwave-metering-switch.groovy

@@ -12,7 +12,7 @@
  *
  */
 metadata {
-	definition (name: "Z-Wave Metering Switch", namespace: "smartthings", author: "SmartThings") {
+	definition (name: "Z-Wave Metering Switch", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.switch") {
 		capability "Energy Meter"
 		capability "Actuator"
 		capability "Switch"
@@ -27,7 +27,7 @@ metadata {
 		command "reset"
 
 		fingerprint inClusters: "0x25,0x32"
-		fingerprint mfr:"0086", prod:"0003", model:"0012", deviceJoinName: "Aeon Labs Micro Smart Switch 2E"
+		fingerprint mfr:"0086", prod:"0003", model:"0012", deviceJoinName: "Aeon Labs Micro Smart Switch"
 	}
 
 	// simulator metadata
@@ -86,7 +86,7 @@ def updated() {
 
 def parse(String description) {
 	def result = null
-	if(description == "updated") return 
+	if(description == "updated") return
 	def cmd = zwave.parse(description, [0x20: 1, 0x32: 1, 0x72: 2])
 	if (cmd) {
 		result = zwaveEvent(cmd)

devicetypes/smartthings/zwave-switch-generic.src/zwave-switch-generic.groovy

@@ -12,7 +12,7 @@
  *
  */
 metadata {
-	definition (name: "Z-Wave Switch Generic", namespace: "smartthings", author: "SmartThings") {
+	definition (name: "Z-Wave Switch Generic", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.switch") {
 		capability "Actuator"
 		capability "Health Check"
  		capability "Switch"

devicetypes/smartthings/zwave-switch-secure.src/zwave-switch-secure.groovy

@@ -12,7 +12,7 @@
  *
  */
 metadata {
-	definition (name: "Z-Wave Switch Secure", namespace: "smartthings", author: "SmartThings") {
+	definition (name: "Z-Wave Switch Secure", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.switch") {
 		capability "Switch"
 		capability "Refresh"
 		capability "Polling"

devicetypes/smartthings/zwave-switch.src/zwave-switch.groovy

@@ -12,7 +12,7 @@
  *
  */
 metadata {
-	definition (name: "Z-Wave Switch", namespace: "smartthings", author: "SmartThings") {
+	definition (name: "Z-Wave Switch", namespace: "smartthings", author: "SmartThings", ocfDeviceType: "oic.d.switch") {
 		capability "Actuator"
 		capability "Indicator"
  		capability "Switch"

devicetypes/smartthings/zwave-thermostat.src/zwave-thermostat.groovy

@@ -42,9 +42,9 @@ metadata {
 		status "auto"			: "command: 4003, payload: 03"
 		status "emergencyHeat"	: "command: 4003, payload: 04"
 
-		status "fanAuto"		: "command: 4403, payload: 00"
-		status "fanOn"			: "command: 4403, payload: 01"
-		status "fanCirculate"	: "command: 4403, payload: 06"
+		status "auto"			: "command: 4403, payload: 00" // "fanAuto"
+		status "on"				: "command: 4403, payload: 01" // "fanOn"
+		status "circulate"		: "command: 4403, payload: 06" // "fanCirculate
 
 		status "heat 60"        : "command: 4303, payload: 01 09 3C"
 		status "heat 68"        : "command: 4303, payload: 01 09 44"
@@ -74,8 +74,9 @@ metadata {
 	}
 
 	tiles {
-		valueTile("temperature", "device.temperature", width: 2, height: 2) {
-			state("temperature", label:'${currentValue}°',
+		// Using standardTile instead of valueTile as it renders the icon better
+		standardTile("temperature", "device.temperature", width: 2, height: 2) {
+			state("temperature", label:'${currentValue}°', icon: "st.thermostat.ac.air-conditioning",
 				backgroundColors:[
 					[value: 31, color: "#153591"],
 					[value: 44, color: "#1e9cbb"],
@@ -88,19 +89,20 @@ metadata {
 			)
 		}
 		standardTile("mode", "device.thermostatMode", inactiveLabel: false, decoration: "flat") {
-			state "off", label:'${name}', action:"switchMode", nextState:"to_heat"
-			state "heat", label:'${name}', action:"switchMode", nextState:"to_cool"
-			state "cool", label:'${name}', action:"switchMode", nextState:"..."
-			state "auto", label:'${name}', action:"switchMode", nextState:"..."
-			state "emergency heat", label:'${name}', action:"switchMode", nextState:"..."
-			state "to_heat", label: "heat", action:"switchMode", nextState:"to_cool"
-			state "to_cool", label: "cool", action:"switchMode", nextState:"..."
+			state "off", action:"switchMode", nextState:"to_heat", icon: "st.thermostat.heating-cooling-off"
+			state "heat", action:"switchMode", nextState:"to_cool", icon: "st.thermostat.heat"
+			state "cool", action:"switchMode", nextState:"...", icon: "st.thermostat.cool"
+			state "auto", action:"switchMode", nextState:"...", icon: "st.thermostat.auto"
+			state "emergency heat", action:"switchMode", nextState:"...", icon: "st.thermostat.emergency-heat"
+			state "to_heat", action:"switchMode", nextState:"to_cool", icon: "st.thermostat.heat"
+			state "to_cool", action:"switchMode", nextState:"...", icon: "st.thermostat.cool"
 			state "...", label: "...", action:"off", nextState:"off"
 		}
 		standardTile("fanMode", "device.thermostatFanMode", inactiveLabel: false, decoration: "flat") {
-			state "fanAuto", label:'${name}', action:"switchFanMode"
-			state "fanOn", label:'${name}', action:"switchFanMode"
-			state "fanCirculate", label:'${name}', action:"switchFanMode"
+			state "auto", action:"switchFanMode", nextState:"...", icon: "st.thermostat.fan-auto" // "fanAuto"
+			state "on", action:"switchFanMode", nextState:"...", icon: "st.thermostat.fan-on" // "fanOn"
+			state "circulate", action:"switchFanMode", nextState:"...", icon: "st.thermostat.fan-circulate" // "fanCirculate"
+			state "...", label: "...", nextState:"..."
 		}
 		controlTile("heatSliderControl", "device.heatingSetpoint", "slider", height: 1, width: 2, inactiveLabel: false) {
 			state "setHeatingSetpoint", action:"quickSetHeat", backgroundColor:"#d04e00"
@@ -117,11 +119,8 @@ metadata {
 		standardTile("refresh", "device.thermostatMode", inactiveLabel: false, decoration: "flat") {
 			state "default", action:"polling.poll", icon:"st.secondary.refresh"
 		}
-		standardTile("configure", "device.configure", inactiveLabel: false, decoration: "flat") {
-			state "configure", label:'', action:"configuration.configure", icon:"st.secondary.configure"
-		}
 		main "temperature"
-		details(["temperature", "mode", "fanMode", "heatSliderControl", "heatingSetpoint", "coolSliderControl", "coolingSetpoint", "refresh", "configure"])
+		details(["temperature", "mode", "fanMode", "heatSliderControl", "heatingSetpoint", "coolSliderControl", "coolingSetpoint", "refresh"])
 	}
 }
 
@@ -286,13 +285,13 @@ def zwaveEvent(physicalgraph.zwave.commands.thermostatfanmodev3.ThermostatFanMod
 	def map = [:]
 	switch (cmd.fanMode) {
 		case physicalgraph.zwave.commands.thermostatfanmodev3.ThermostatFanModeReport.FAN_MODE_AUTO_LOW:
-			map.value = "fanAuto"
+			map.value = "auto" // "fanAuto"
 			break
 		case physicalgraph.zwave.commands.thermostatfanmodev3.ThermostatFanModeReport.FAN_MODE_LOW:
-			map.value = "fanOn"
+			map.value = "on" // "fanOn"
 			break
 		case physicalgraph.zwave.commands.thermostatfanmodev3.ThermostatFanModeReport.FAN_MODE_CIRCULATION:
-			map.value = "fanCirculate"
+			map.value = "circulate" // "fanCirculate"
 			break
 	}
 	map.name = "thermostatFanMode"
@@ -309,15 +308,19 @@ def zwaveEvent(physicalgraph.zwave.commands.thermostatmodev2.ThermostatModeSuppo
 	if(cmd.auto) { supportedModes += "auto " }
 
 	state.supportedModes = supportedModes
+	// No events to be generated, return empty map
+	return [:]
 }
 
 def zwaveEvent(physicalgraph.zwave.commands.thermostatfanmodev3.ThermostatFanModeSupportedReport cmd) {
 	def supportedFanModes = ""
-	if(cmd.auto) { supportedFanModes += "fanAuto " }
-	if(cmd.low) { supportedFanModes += "fanOn " }
-	if(cmd.circulation) { supportedFanModes += "fanCirculate " }
+	if(cmd.auto) { supportedFanModes += "auto " } // "fanAuto "
+	if(cmd.low) { supportedFanModes += "on " } // "fanOn"
+	if(cmd.circulation) { supportedFanModes += "circulate " } // "fanCirculate"
 
 	state.supportedFanModes = supportedFanModes
+	// No events to be generated, return empty map
+	return [:]
 }
 
 def zwaveEvent(physicalgraph.zwave.commands.basicv1.BasicReport cmd) {
@@ -412,7 +415,13 @@ def configure() {
 	delayBetween([
 		zwave.thermostatModeV2.thermostatModeSupportedGet().format(),
 		zwave.thermostatFanModeV3.thermostatFanModeSupportedGet().format(),
-		zwave.associationV1.associationSet(groupingIdentifier:1, nodeId:[zwaveHubNodeId]).format()
+		zwave.associationV1.associationSet(groupingIdentifier:1, nodeId:[zwaveHubNodeId]).format(),
+		zwave.sensorMultilevelV3.sensorMultilevelGet().format(), // current temperature
+		zwave.thermostatSetpointV1.thermostatSetpointGet(setpointType: 1).format(),
+		zwave.thermostatSetpointV1.thermostatSetpointGet(setpointType: 2).format(),
+		zwave.thermostatModeV2.thermostatModeGet().format(),
+		zwave.thermostatFanModeV3.thermostatFanModeGet().format(),
+		zwave.thermostatOperatingStateV1.thermostatOperatingStateGet().format()
 	], 2300)
 }
 
@@ -453,11 +462,11 @@ def switchToMode(nextMode) {
 def switchFanMode() {
 	def currentMode = device.currentState("thermostatFanMode")?.value
 	def lastTriedMode = state.lastTriedFanMode ?: currentMode ?: "off"
-	def supportedModes = getDataByName("supportedFanModes") ?: "fanAuto fanOn"
-	def modeOrder = ["fanAuto", "fanCirculate", "fanOn"]
+	def supportedModes = getDataByName("supportedFanModes") ?: "auto on" // "fanAuto fanOn"
+	def modeOrder = ["auto", "circulate", "on"]                 // "fanAuto", "fanCirculate", "fanOn"
 	def next = { modeOrder[modeOrder.indexOf(it) + 1] ?: modeOrder[0] }
 	def nextMode = next(lastTriedMode)
-	while (!supportedModes?.contains(nextMode) && nextMode != "fanAuto") {
+	while (!supportedModes?.contains(nextMode) && nextMode != "auto") { // "fanAuto"
 		nextMode = next(nextMode)
 	}
 	switchToFanMode(nextMode)
@@ -468,11 +477,11 @@ def switchToFanMode(nextMode) {
 	if(supportedFanModes && !supportedFanModes.contains(nextMode)) log.warn "thermostat mode '$nextMode' is not supported"
 
 	def returnCommand
-	if (nextMode == "fanAuto") {
+	if (nextMode == "auto") { // "fanAuto"
 		returnCommand = fanAuto()
-	} else if (nextMode == "fanOn") {
+	} else if (nextMode == "on") { // "fanOn"
 		returnCommand = fanOn()
-	} else if (nextMode == "fanCirculate") {
+	} else if (nextMode == "circulate") { // "fanCirculate"
 		returnCommand = fanCirculate()
 	} else {
 		log.debug("no fan mode '$nextMode'")