Merge pull request #1367 from surfous/DVCSMP-2134-2135-ZLL-bulb-hchk2

Add health check for:
* DVCSMP-2134 ZLL white color temperature bulb
* DVCSMP-2135 ZLL dimmer bulb

devicetypes/smartthings/dimmer-switch.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/dimmer-switch.src/README.md

@@ -0,0 +1,45 @@
+# Z-wave Dimmer Switch
+
+
+
+Works with:
+
+* [GE Z-Wave In-Wall Smart Dimmer (GE 12724)](http://products.z-wavealliance.org/products/1197)
+* [GE Z-Wave In-Wall Smart Dimmer (Toggle) (GE 12729)](http://products.z-wavealliance.org/products/1201)
+* [GE Z-Wave Plug-in Smart Dimmer (GE 12718)](http://products.z-wavealliance.org/products/1191)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#Troubleshooting)
+
+## Capabilities
+
+* **Switch Level** - it's defined to accept two parameters, the level and the rate of dimming
+* **Actuator** - represents that a Device has commands
+* **Indicator** - gives you the ability to set the indicator LED light on a Z-Wave switch
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Z-Wave Smart Dimmers (In-Wall, In-Wall(Toggle), Plug-In) are polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Check-in interval = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [General Z-Wave Dimmer/Switch Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200955890-Troubleshooting-GE-in-wall-switch-or-dimmer-won-t-respond-to-commands-or-automations-Z-Wave-)
+* [GE Z-Wave In-Wall Smart Dimmer (GE 12724) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200902600-GE-In-Wall-Paddle-Dimmer-Switch-GE-12724-Z-Wave-)
+* [GE Z-Wave In-Wall Smart Dimmer (Toggle) (GE 12729) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/207568463-GE-In-Wall-Smart-Toggle-Dimmer-GE-12729-Z-Wave-)
+* [GE Z-Wave Plug-in Smart Dimmer (GE 12718) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/202088474-GE-Plug-In-Smart-Dimmer-GE-12718-Z-Wave-)

devicetypes/smartthings/dimmer-switch.src/dimmer-switch.groovy

@@ -20,6 +20,7 @@ metadata {
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
+		capability "Health Check"
 
 		fingerprint mfr:"0063", prod:"4457", deviceJoinName: "Z-Wave Wall Dimmer"
 		fingerprint mfr:"0063", prod:"4944", deviceJoinName: "Z-Wave Wall Dimmer"
@@ -82,6 +83,8 @@ metadata {
 }
 
 def updated(){
+	// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
   switch (ledIndicator) {
         case "on":
             indicatorWhenOn()
@@ -215,6 +218,13 @@ def poll() {
 	zwave.switchMultilevelV1.switchMultilevelGet().format()
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	log.debug "refresh() is called"
 	def commands = []

devicetypes/smartthings/osram-lightify-gardenspot-mini-rgb.src/osram-lightify-gardenspot-mini-rgb.groovy

@@ -21,9 +21,6 @@ metadata {
         attribute "colorName", "string"
 
         command "setAdjustedColor"
-
-        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Gardenspot RGB"
-		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY Gardenspot RGB"
     }
 
     // simulator metadata

devicetypes/smartthings/smartpower-dimming-outlet.src/smartpower-dimming-outlet.groovy

@@ -133,7 +133,7 @@ def refresh() {
 }
 
 def configure() {
-	onOffConfig() + levelConfig() + powerConfig() + refresh()
+	refresh() + onOffConfig() + levelConfig() + powerConfig()
 }
 
 

devicetypes/smartthings/smartpower-outlet.src/smartpower-outlet.groovy

@@ -146,7 +146,7 @@ def configure() {
 	sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	// OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-	zigbee.onOffConfig(0, 300) + powerConfig() + refresh()
+	refresh() + zigbee.onOffConfig(0, 300) + powerConfig()
 }
 
 //power config for devices with min reporting interval as 1 seconds and reporting interval if no activity as 10min (600s)

devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy

@@ -308,16 +308,9 @@ def configure() {
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
 	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
-	log.debug "Configuring Reporting, IAS CIE, and Bindings."
-	def enrollCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 1", "delay 500",
-	]
-
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	return enrollCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) + refresh() // send refresh cmds as part of config
+	return refresh() + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy

@@ -323,16 +323,9 @@ def configure() {
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
 	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
-	log.debug "Configuring Reporting, IAS CIE, and Bindings."
-
-	def enrollCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
-	]
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	return enrollCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) + refresh() // send refresh cmds as part of config
+	return refresh() + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-motion-temp-sensor.src/smartsense-motion-temp-sensor.groovy

@@ -255,13 +255,9 @@ def refresh() {
 }
 
 def configure() {
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
 	log.debug "Configuring Reporting, IAS CIE, and Bindings."
 
 	def configCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
-
 		"zdo bind 0x${device.deviceNetworkId} ${endpointId} 1 1 {${device.zigbeeId}} {}", "delay 200",
 		"zcl global send-me-a-report 1 0x20 0x20 30 21600 {01}",		//checkin time 6 hrs
 		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
@@ -270,7 +266,7 @@ def configure() {
 		"zcl global send-me-a-report 0x402 0 0x29 30 3600 {6400}",
 		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500"
 	]
-    return configCmds + refresh() // send refresh cmds as part of config
+    return refresh() + configCmds  // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-multi-sensor.src/smartsense-multi-sensor.groovy

@@ -420,15 +420,14 @@ def configure() {
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	def configCmds = enrollResponse() +
-			zigbee.batteryConfig() +
+	def configCmds = zigbee.batteryConfig() +
 			zigbee.temperatureConfig(30, 300) +
 			zigbee.configureReporting(0xFC02, 0x0010, 0x18, 10, 3600, 0x01, [mfgCode: manufacturerCode]) +
 			zigbee.configureReporting(0xFC02, 0x0012, 0x29, 1, 3600, 0x0001, [mfgCode: manufacturerCode]) +
 			zigbee.configureReporting(0xFC02, 0x0013, 0x29, 1, 3600, 0x0001, [mfgCode: manufacturerCode]) +
 			zigbee.configureReporting(0xFC02, 0x0014, 0x29, 1, 3600, 0x0001, [mfgCode: manufacturerCode])
 
-	return configCmds + refresh()
+	return refresh() + configCmds
 }
 
 private getEndpointId() {

devicetypes/smartthings/smartsense-open-closed-accelerometer-sensor.src/smartsense-open-closed-accelerometer-sensor.groovy

@@ -277,12 +277,8 @@ def getTemperature(value) {
 def configure() {
 	sendEvent(name: "checkInterval", value: 7200, displayed: false)
 
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
 	log.debug "Configuring Reporting, IAS CIE, and Bindings."
 	def configCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
-
 		"zdo bind 0x${device.deviceNetworkId} ${endpointId} 1 1 {${device.zigbeeId}} {}", "delay 200",
 		"zcl global send-me-a-report 1 0x20 0x20 30 21600 {01}",		//checkin time 6 hrs
 		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
@@ -295,7 +291,7 @@ def configure() {
 		"zcl global send-me-a-report 0xFC02 2 0x18 30 3600 {01}",
 		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500"
 	]
-	return configCmds + refresh() // send refresh cmds as part of config
+	return refresh() + configCmds // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy

@@ -270,16 +270,11 @@ def configure() {
 	// enrolls with default periodic reporting until newer 5 min interval is confirmed
 	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
 	log.debug "Configuring Reporting, IAS CIE, and Bindings."
-	def enrollCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 1", "delay 500",
-	]
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-    return enrollCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) + refresh() // send refresh cmds as part of config
+    return refresh() + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy

@@ -250,11 +250,7 @@ private Map getTemperatureResult(value) {
 
 private Map getHumidityResult(value) {
 	log.debug 'Humidity'
-	return [
-		name: 'humidity',
-		value: value,
-		unit: '%'
-	]
+	return value ? [name: 'humidity', value: value, unit: '%'] : [:]
 }
 
 /**
@@ -267,15 +263,10 @@ def ping() {
 def refresh()
 {
 	log.debug "refresh temperature, humidity, and battery"
-	[
-
-		"zcl mfg-code 0xC2DF", "delay 1000",
-		"zcl global read 0xFC45 0", "delay 1000",
-		"send 0x${device.deviceNetworkId} 1 1", "delay 1000",
-        "st rattr 0x${device.deviceNetworkId} 1 0x402 0", "delay 200",
-        "st rattr 0x${device.deviceNetworkId} 1 1 0x20"
-
-	]
+	return zigbee.readAttribute(0xFC45, 0x0000, ["mfgCode": 0xC2DF]) +   // Original firmware
+			zigbee.readAttribute(0xFC45, 0x0000, ["mfgCode": 0x104E]) +  // New firmware
+			zigbee.readAttribute(0x0402, 0x0000) +
+			zigbee.readAttribute(0x0001, 0x0020)
 }
 
 def configure() {
@@ -292,7 +283,7 @@ def configure() {
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	return humidityConfigCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) +  refresh() // send refresh cmds as part of config
+	return refresh() + humidityConfigCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300)  // send refresh cmds as part of config
 }
 
 private hex(value) {

devicetypes/smartthings/zigbee-button.src/zigbee-button.groovy

@@ -89,14 +89,8 @@ def parse(String description) {
 }
 
 private Map parseIasButtonMessage(String description) {
-    int zoneInt = Integer.parseInt((description - "zone status 0x"), 16)
-    if (zoneInt & 0x02) {
-        resultMap = getButtonResult('press')
-    } else {
-        resultMap = getButtonResult('release')
-    }
-
-    return resultMap
+    def zs = zigbee.parseZoneStatus(description)
+    return zs.isAlarm2Set() ? getButtonResult("press") : getButtonResult("release")
 }
 
 private Map getBatteryResult(rawValue) {

devicetypes/smartthings/zigbee-dimmer-power.src/zigbee-dimmer-power.groovy

@@ -93,5 +93,5 @@ def refresh() {
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh()
+    refresh()
 }

devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy

@@ -107,5 +107,5 @@ def configure() {
     sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig()
 }

devicetypes/smartthings/zigbee-lock.src/zigbee-lock.groovy

@@ -90,7 +90,7 @@ def configure() {
         zigbee.configureReporting(CLUSTER_POWER, POWER_ATTR_BATTERY_PERCENTAGE_REMAINING,
                                   TYPE_U8, 600, 21600, 0x01)
     log.info "configure() --- cmds: $cmds"
-    return cmds + refresh() // send refresh cmds as part of config
+    return refresh() + cmds // send refresh cmds as part of config
 }
 
 def refresh() {

devicetypes/smartthings/zigbee-rgb-bulb.src/zigbee-rgb-bulb.groovy

@@ -0,0 +1,154 @@
+/**
+ *  Copyright 2016 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ *  Author: SmartThings
+ *  Date: 2016-01-19
+ *
+ *  This DTH should serve as the generic DTH to handle RGB ZigBee HA devices (For color bulbs with no color temperature)
+ */
+
+metadata {
+	definition (name: "ZigBee RGB Bulb", namespace: "smartthings", author: "SmartThings") {
+
+		capability "Actuator"
+		capability "Color Control"
+		capability "Configuration"
+		capability "Polling"
+		capability "Refresh"
+		capability "Switch"
+		capability "Switch Level"
+		capability "Health Check"
+
+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Gardenspot RGB", deviceJoinName: "OSRAM LIGHTIFY Gardenspot mini RGB"
+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY Gardenspot RGB", deviceJoinName: "OSRAM LIGHTIFY Gardenspot mini RGB"
+	}
+
+	// UI tile definitions
+	tiles(scale: 2) {
+		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
+			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
+				attributeState "on", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
+				attributeState "off", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
+				attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
+				attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
+			}
+			tileAttribute ("device.level", key: "SLIDER_CONTROL") {
+				attributeState "level", action:"switch level.setLevel"
+			}
+			tileAttribute ("device.color", key: "COLOR_CONTROL") {
+				attributeState "color", action:"color control.setColor"
+			}
+		}
+		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
+			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
+		}
+
+		main(["switch"])
+		details(["switch", "refresh"])
+	}
+}
+
+//Globals
+private getATTRIBUTE_HUE() { 0x0000 }
+private getATTRIBUTE_SATURATION() { 0x0001 }
+private getHUE_COMMAND() { 0x00 }
+private getSATURATION_COMMAND() { 0x03 }
+private getCOLOR_CONTROL_CLUSTER() { 0x0300 }
+
+// Parse incoming device messages to generate events
+def parse(String description) {
+	log.debug "description is $description"
+
+	def event = zigbee.getEvent(description)
+	if (event) {
+		log.debug event
+		if (event.name=="level" && event.value==0) {}
+		else {
+			sendEvent(event)
+		}
+	}
+	else {
+		def zigbeeMap = zigbee.parseDescriptionAsMap(description)
+		def cluster = zigbee.parse(description)
+
+		if (zigbeeMap?.clusterInt == COLOR_CONTROL_CLUSTER) {
+			if(zigbeeMap.attrInt == ATTRIBUTE_HUE){  //Hue Attribute
+				def hueValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
+				sendEvent(name: "hue", value: hueValue, descriptionText: "Color has changed")
+			}
+			else if(zigbeeMap.attrInt == ATTRIBUTE_SATURATION){ //Saturation Attribute
+				def saturationValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
+				sendEvent(name: "saturation", value: saturationValue, descriptionText: "Color has changed", displayed: false)
+			}
+		}
+		else if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
+			if (cluster.data[0] == 0x00){
+				log.debug "ON/OFF REPORTING CONFIG RESPONSE: $cluster"
+				sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+			}
+			else {
+				log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+			}
+		}
+		else {
+			log.info "DID NOT PARSE MESSAGE for description : $description"
+			log.debug zigbeeMap
+		}
+	}
+}
+
+def on() {
+	zigbee.on()
+}
+
+def off() {
+	zigbee.off()
+}
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	return zigbee.onOffRefresh()
+}
+
+def refresh() {
+	zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION) + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
+}
+
+def configure() {
+	log.debug "Configuring Reporting and Bindings."
+	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// enrolls with default periodic reporting until newer 5 min interval is confirmed
+	sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+
+	// OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
+	zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01) + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
+}
+
+def setLevel(value) {
+	zigbee.setLevel(value)
+}
+
+def setColor(value){
+	log.trace "setColor($value)"
+	zigbee.on() + setHue(value.hue) + "delay 500" + setSaturation(value.saturation)
+}
+
+def setHue(value) {
+	def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
+	zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500")       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
+}
+
+def setSaturation(value) {
+	def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
+	zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + "delay 1000" + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
+}

devicetypes/smartthings/zigbee-rgbw-bulb.src/zigbee-rgbw-bulb.groovy

@@ -138,7 +138,7 @@ def ping() {
 }
 
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.readAttribute(0x0008, 0x00) + zigbee.readAttribute(0x0300, 0x00) + zigbee.readAttribute(0x0300, ATTRIBUTE_COLOR_TEMPERATURE) + zigbee.readAttribute(0x0300, ATTRIBUTE_HUE) + zigbee.readAttribute(0x0300, ATTRIBUTE_SATURATION) + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_COLOR_TEMPERATURE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION) + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
 }
 
 def configure() {
@@ -148,7 +148,7 @@ def configure() {
     sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01) + zigbee.readAttribute(0x0006, 0x00) + zigbee.readAttribute(0x0008, 0x00) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, 0x00) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_COLOR_TEMPERATURE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
+    refresh()
 }
 
 def setColorTemperature(value) {

devicetypes/smartthings/zigbee-switch-power.src/zigbee-switch-power.groovy

@@ -82,5 +82,5 @@ def refresh() {
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig() + zigbee.onOffRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh()
+    refresh()
 }

devicetypes/smartthings/zigbee-switch.src/zigbee-switch.groovy

@@ -78,5 +78,5 @@ def refresh() {
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.onOffRefresh()
+    zigbee.onOffRefresh() + zigbee.onOffConfig()
 }

devicetypes/smartthings/zigbee-valve.src/zigbee-valve.groovy

@@ -134,10 +134,5 @@ def refresh() {
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() +
-    zigbee.configureReporting(CLUSTER_POWER, POWER_ATTR_BATTERY_PERCENTAGE_REMAINING, TYPE_U8, 600, 21600, 1) +
-    zigbee.configureReporting(CLUSTER_BASIC, BASIC_ATTR_POWER_SOURCE, TYPE_ENUM8, 5, 21600, 1) +
-    zigbee.onOffRefresh() +
-    zigbee.readAttribute(CLUSTER_BASIC, BASIC_ATTR_POWER_SOURCE) +
-    zigbee.readAttribute(CLUSTER_POWER, POWER_ATTR_BATTERY_PERCENTAGE_REMAINING)
+    refresh()
 }

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/zigbee-white-color-temperature-bulb.groovy

@@ -131,7 +131,7 @@ def configure() {
     sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
+    refresh()
 }
 
 def setColorTemperature(value) {

devicetypes/smartthings/zll-dimmer-bulb.src/zll-dimmer-bulb.groovy

@@ -11,6 +11,9 @@
  *  for the specific language governing permissions and limitations under the License.
  *
  */
+import groovy.transform.Field
+
+@Field Boolean hasConfiguredHealthCheck = false
 
 metadata {
     definition (name: "ZLL Dimmer Bulb", namespace: "smartthings", author: "SmartThings") {
@@ -21,6 +24,7 @@ metadata {
         capability "Refresh"
         capability "Switch"
         capability "Switch Level"
+        capability "Health Check"
 
         //fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0000,0019"
         fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0019"
@@ -96,7 +100,38 @@ def poll() {
     refresh()
 }
 
-def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+    return zigbee.levelRefresh()
+}
+
+def healthPoll() {
+    log.debug "healthPoll()"
+    def cmds = refresh()
+    cmds.each{ sendHubCommand(new physicalgraph.device.HubAction(it))}
+}
+
+def configureHealthCheck() {
+    Integer hcIntervalMinutes = 12
+    if (!hasConfiguredHealthCheck) {
+        log.debug "Configuring Health Check, Reporting"
+        unschedule("healthPoll")
+        runEvery5Minutes("healthPoll")
+        // Device-Watch allows 2 check-in misses from device
+        sendEvent(name: "checkInterval", value: hcIntervalMinutes * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+        hasConfiguredHealthCheck = true
+    }
+}
+
+def configure() {
+    log.debug "configure()"
+    zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()
+    configureHealthCheck()
+}
+
+def updated() {
+    log.debug "updated()"
+    configureHealthCheck()
 }

devicetypes/smartthings/zll-rgb-bulb.src/zll-rgb-bulb.groovy

@@ -0,0 +1,134 @@
+/**
+ *  Copyright 2016 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+
+metadata {
+	definition (name: "ZLL RGB Bulb", namespace: "smartthings", author: "SmartThings") {
+
+		capability "Actuator"
+		capability "Color Control"
+		capability "Configuration"
+		capability "Polling"
+		capability "Refresh"
+		capability "Switch"
+		capability "Switch Level"
+	}
+
+	// UI tile definitions
+	tiles(scale: 2) {
+		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
+			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
+				attributeState "on", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
+				attributeState "off", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
+				attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
+				attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
+			}
+			tileAttribute ("device.level", key: "SLIDER_CONTROL") {
+				attributeState "level", action:"switch level.setLevel"
+			}
+			tileAttribute ("device.color", key: "COLOR_CONTROL") {
+				attributeState "color", action:"color control.setColor"
+			}
+		}
+		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
+			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
+		}
+
+		main(["switch"])
+		details(["switch", "refresh"])
+	}
+}
+
+//Globals
+private getATTRIBUTE_HUE() { 0x0000 }
+private getATTRIBUTE_SATURATION() { 0x0001 }
+private getHUE_COMMAND() { 0x00 }
+private getSATURATION_COMMAND() { 0x03 }
+private getCOLOR_CONTROL_CLUSTER() { 0x0300 }
+
+// Parse incoming device messages to generate events
+def parse(String description) {
+	log.debug "description is $description"
+
+	def finalResult = zigbee.getEvent(description)
+	if (finalResult) {
+		log.debug finalResult
+		sendEvent(finalResult)
+	}
+	else {
+		def zigbeeMap = zigbee.parseDescriptionAsMap(description)
+		log.trace "zigbeeMap : $zigbeeMap"
+
+		if (zigbeeMap?.clusterInt == COLOR_CONTROL_CLUSTER) {
+			if(zigbeeMap.attrInt == ATTRIBUTE_HUE){  //Hue Attribute
+				def hueValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 360)
+				sendEvent(name: "hue", value: hueValue, displayed:false)
+			}
+			else if(zigbeeMap.attrInt == ATTRIBUTE_SATURATION){ //Saturation Attribute
+				def saturationValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
+				sendEvent(name: "saturation", value: saturationValue, displayed:false)
+			}
+		}
+		else {
+			log.info "DID NOT PARSE MESSAGE for description : $description"
+		}
+	}
+}
+
+def on() {
+	zigbee.on() + ["delay 1500"] + zigbee.onOffRefresh()
+}
+
+def off() {
+	zigbee.off() + ["delay 1500"] + zigbee.onOffRefresh()
+}
+
+def refresh() {
+	refreshAttributes() + configureAttributes()
+}
+
+def poll() {
+	refreshAttributes()
+}
+
+def configure() {
+	log.debug "Configuring Reporting and Bindings."
+	configureAttributes() + refreshAttributes()
+}
+
+def configureAttributes() {
+	zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
+}
+
+def refreshAttributes() {
+	zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
+}
+
+def setLevel(value) {
+	zigbee.setLevel(value) + ["delay 1500"] + zigbee.levelRefresh()         //adding refresh because of ZLL bulb not conforming to send-me-a-report
+}
+
+def setColor(value){
+	log.trace "setColor($value)"
+	zigbee.on() + setHue(value.hue) + ["delay 300"] + setSaturation(value.saturation) + ["delay 2000"] + refreshAttributes()
+}
+
+def setHue(value) {
+	def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
+	zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE)      //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
+}
+
+def setSaturation(value) {
+	def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
+	zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)      //payload-> sat value, transition time
+}

devicetypes/smartthings/zll-rgbw-bulb.src/zll-rgbw-bulb.groovy

@@ -123,7 +123,7 @@ def configureAttributes() {
 }
 
 def refreshAttributes() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.readAttribute(0x0300, 0x00) + zigbee.readAttribute(0x0300, ATTRIBUTE_HUE) + zigbee.readAttribute(0x0300, ATTRIBUTE_SATURATION)
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
 }
 
 def setColorTemperature(value) {
@@ -141,10 +141,10 @@ def setColor(value){
 
 def setHue(value) {
     def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500")       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
+    zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE)       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
 }
 
 def setSaturation(value) {
     def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500")      //payload-> sat value, transition time
+    zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)      //payload-> sat value, transition time
 }

devicetypes/smartthings/zll-white-color-temperature-bulb.src/zll-white-color-temperature-bulb.groovy

@@ -11,6 +11,9 @@
  *  for the specific language governing permissions and limitations under the License.
  *
  */
+import groovy.transform.Field
+
+@Field Boolean hasConfiguredHealthCheck = false
 
 metadata {
     definition (name: "ZLL White Color Temperature Bulb", namespace: "smartthings", author: "SmartThings") {
@@ -22,6 +25,7 @@ metadata {
         capability "Refresh"
         capability "Switch"
         capability "Switch Level"
+        capability "Health Check"
 
         attribute "colorName", "string"
         command "setGenericName"
@@ -96,9 +100,41 @@ def poll() {
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+    return zigbee.levelRefresh()
+}
+
+def healthPoll() {
+    log.debug "healthPoll()"
+    def cmds = zigbee.onOffRefresh() + zigbee.levelRefresh()
+    cmds.each{ sendHubCommand(new physicalgraph.device.HubAction(it))}
+}
+
+def configureHealthCheck() {
+    Integer hcIntervalMinutes = 12
+    if (!hasConfiguredHealthCheck) {
+        log.debug "Configuring Health Check, Reporting"
+        unschedule("healthPoll")
+        runEvery5Minutes("healthPoll")
+        // Device-Watch allows 2 check-in misses from device
+        sendEvent(name: "checkInterval", value: hcIntervalMinutes * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+        hasConfiguredHealthCheck = true
+    }
+}
+
 def configure() {
-    log.debug "Configuring Reporting and Bindings."
+    log.debug "configure()"
+    configureHealthCheck()
     zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
+
+}
+
+def updated() {
+    log.debug "updated()"
+    configureHealthCheck()
 }
 
 def setColorTemperature(value) {

devicetypes/smartthings/zwave-switch-generic.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-switch-generic.src/README.md

@@ -0,0 +1,39 @@
+# Z-wave Switch
+
+
+
+Works with: 
+
+* [Leviton Appliance Module (DZPA1-1LW)](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
+* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave)](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Health Check** - indicates ability to get device health notifications
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+
+## Device Health
+
+A Category C5 Leviton Appliance Module (DZPA1-1LW) and GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Leviton Appliance Module (DZPA1-1LW) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
+* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)

devicetypes/smartthings/zwave-switch-generic.src/zwave-switch-generic.groovy

@@ -14,12 +14,15 @@
 metadata {
 	definition (name: "Z-Wave Switch Generic", namespace: "smartthings", author: "SmartThings") {
 		capability "Actuator"
+		capability "Health Check"
  		capability "Switch"
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
 
 		fingerprint inClusters: "0x25", deviceJoinName: "Z-Wave Switch"
+		fingerprint mfr:"001D", prod:"1A02", deviceJoinName: "Z-Wave Switch"
+		fingerprint mfr:"0063", prod:"4F50", deviceJoinName: "Z-Wave Switch"
 	}
 
 	// simulator metadata
@@ -50,6 +53,11 @@ metadata {
 	}
 }
 
+def updated(){
+// Device-Watch simply pings if no device events received for checkInterval duration of 32min = 2 * 15min + 2min lag time
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description) {
 	def result = null
 	def cmd = zwave.parse(description, [0x20: 1, 0x70: 1])
@@ -126,6 +134,13 @@ def poll() {
 	])
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),

devicetypes/smartthings/zwave-switch.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-switch.src/README.md

@@ -0,0 +1,49 @@
+# Z-Wave Switch
+
+
+Works with: 
+
+* [GE Z-Wave Plug-In Smart Switch (12719)](http://products.z-wavealliance.org/products/1193)
+* [GE Z-Wave In-Wall Smart Outlet (12721)](http://products.z-wavealliance.org/products/1195)
+* [GE Z-Wave In-Wall Smart Switch (12722)](http://products.z-wavealliance.org/products/1196)
+* [GE Z-Wave In-Wall Smart Toggle Switch (12727)](http://products.z-wavealliance.org/products/1200)
+
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#Troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Indicator** - gives you the ability to set the indicator LED light on a Z-Wave switch
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Z-Wave Switches (Plug-In, In-Wall(Toggle Switch, Switch, Outlet)) are polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [General Z-Wave Dimmer/Switch Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200955890-Troubleshooting-GE-in-wall-switch-or-dimmer-won-t-respond-to-commands-or-automations-Z-Wave-)
+* [GE Z-Wave Plug-In Smart Switch (12719) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200903070-GE-Plug-In-Smart-Switch-GE-12719-Z-Wave)
+* [GE Z-Wave In-Wall Smart Outlet (12721) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200903020-GE-In-Wall-Smart-Outlet-GE-12721-Z-Wave)
+* [GE Z-Wave In-Wall Smart Switch (12722) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200902540-GE-In-Wall-Smart-Switch-GE-12722-Z-Wave)
+* [GE Z-Wave In-Wall Smart Toggle Switch (12727) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/207568933-GE-In-Wall-Smart-Toggle-Switch-GE-12727-Z-Wave)
+
+

devicetypes/smartthings/zwave-switch.src/zwave-switch.groovy

@@ -19,6 +19,7 @@ metadata {
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
+		capability "Health Check"
 
 		fingerprint mfr:"0063", prod:"4952", deviceJoinName: "Z-Wave Wall Switch"
 		fingerprint mfr:"0063", prod:"5257", deviceJoinName: "Z-Wave Wall Switch"
@@ -64,6 +65,8 @@ metadata {
 }
 
 def updated(){
+		// Device-Watch simply pings if no device events received for 32min(checkInterval)
+		sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
   switch (ledIndicator) {
         case "on":
             indicatorWhenOn()
@@ -156,6 +159,13 @@ def poll() {
 	])
 }
 
+/**
+  * PING is used by Device-Watch in attempt to reach the Device
+**/
+def ping() {
+		refresh()
+}
+
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),