Merge pull request #1378 from surfous/DVCSMP-2155-ZigBee-switch-power-dh-hchk

DVCSMP-2155 ZigBee switch power DH health check

devicetypes/fibargroup/fibaro-motion-sensor-zw5.src/fibaro-motion-sensor-zw5.groovy

@@ -127,9 +127,10 @@ def zwaveEvent(physicalgraph.zwave.commands.sensormultilevelv5.SensorMultilevelR
 	def map = [ displayed: true ]
     switch (cmd.sensorType) {
     	case 1:
-        	map.name = "temperature"
-            map.unit = cmd.scale == 1 ? "F" : "C"
-            map.value = convertTemperatureIfNeeded(cmd.scaledSensorValue, map.unit, cmd.precision)
+			def cmdScale = cmd.scale == 1 ? "F" : "C"
+			map.name = "temperature"
+            map.unit = getTemperatureScale()
+            map.value = convertTemperatureIfNeeded(cmd.scaledSensorValue, cmdScale, cmd.precision)
             break
     	case 3:
         	map.name = "illuminance"

devicetypes/smartthings/arrival-sensor.src/arrival-sensor.groovy

@@ -87,16 +87,27 @@ def beep() {
 	up to this long from the time you send the message to the time you hear a sound.
 	*/
 
+	// Used source endpoint of 0x02 because we are using smartthings manufacturer specific cluster.
 	[
 		"raw 0xFC05 {15 0A 11 00 00 15 01}",
+		"delay 200",
+		"send 0x$zigbee.deviceNetworkId 0x02 0x$zigbee.endpointId",
 		"delay 7000",
 		"raw 0xFC05 {15 0A 11 00 00 15 01}",
+		"delay 200",
+		"send 0x$zigbee.deviceNetworkId 0x02 0x$zigbee.endpointId",
 		"delay 7000",
 		"raw 0xFC05 {15 0A 11 00 00 15 01}",
+		"delay 200",
+		"send 0x$zigbee.deviceNetworkId 0x02 0x$zigbee.endpointId",
 		"delay 7000",
 		"raw 0xFC05 {15 0A 11 00 00 15 01}",
+		"delay 200",
+		"send 0x$zigbee.deviceNetworkId 0x02 0x$zigbee.endpointId",
 		"delay 7000",
-		"raw 0xFC05 {15 0A 11 00 00 15 01}"
+		"raw 0xFC05 {15 0A 11 00 00 15 01}",
+		"delay 200",
+		"send 0x$zigbee.deviceNetworkId 0x02 0x$zigbee.endpointId",
 	]
 }
 

devicetypes/smartthings/centralite-dimmer.src/centralite-dimmer.groovy

@@ -105,11 +105,21 @@ def parseDescriptionAsMap(description) {
 
 // Commands to device
 def on() {
-	'zcl on-off on'
+	[
+			'zcl on-off on',
+			'delay 200',
+			"send 0x${zigbee.deviceNetworkId} 0x01 0x${zigbee.endpointId}",
+			'delay 500'
+	]
 }
 
 def off() {
-	'zcl on-off off'
+	[
+			'zcl on-off off',
+			'delay 200',
+			"send 0x${zigbee.deviceNetworkId} 0x01 0x${zigbee.endpointId}",
+			'delay 500'
+	]
 }
 
 def setLevel(value) {

devicetypes/smartthings/cree-bulb.src/README.md

@@ -23,10 +23,8 @@ Works with:
 
 ## Device Health
 
-A Category C6 Connected Cree LED Bulb with maxReportTime of 10 min.
-Check-in interval is double the value of maxReportTime for Zigbee device. 
-This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 2*10 = 20 min
+A Category C6 Connected Cree LED Bulb with maxReportTime of 5 mins.
+Check-in interval = 12 mins
 
 ## Troubleshooting
 

devicetypes/smartthings/cree-bulb.src/cree-bulb.groovy

@@ -19,7 +19,6 @@ metadata {
 
         capability "Actuator"
         capability "Configuration"
-        capability "Polling"
         capability "Refresh"
         capability "Switch"
         capability "Switch Level"
@@ -60,6 +59,15 @@ metadata {
     }
 }
 
+def installed() {
+    log.debug "${device} installed"
+}
+
+def updated() {
+    log.debug "${device} updated"
+    configureHealthCheck()
+}
+
 // Parse incoming device messages to generate events
 def parse(String description) {
     log.debug "description is $description"
@@ -94,17 +102,23 @@ def ping() {
 }
 
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig() + zigbee.levelConfig()
-}
-
-def poll() {
     zigbee.onOffRefresh() + zigbee.levelRefresh()
 }
 
-def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-    sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
-    // minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()
+def configureHealthCheck() {
+    log.debug "configureHealthCheck"
+    unschedule("healthPoll")
+    runEvery5Minutes("healthPoll")
+    // Device-Watch allows 2 check-in misses from device
+    sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+}
+
+def healthPoll() {
+    log.debug "healthPoll()"
+    def cmds = zigbee.onOffRefresh() + zigbee.levelRefresh()
+    cmds.each{ sendHubCommand(new physicalgraph.device.HubAction(it))}
+}
+
+def configure() {
+    refresh()
 }

devicetypes/smartthings/dimmer-switch.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/dimmer-switch.src/README.md

@@ -0,0 +1,45 @@
+# Z-wave Dimmer Switch
+
+
+
+Works with:
+
+* [GE Z-Wave In-Wall Smart Dimmer (GE 12724)](http://products.z-wavealliance.org/products/1197)
+* [GE Z-Wave In-Wall Smart Dimmer (Toggle) (GE 12729)](http://products.z-wavealliance.org/products/1201)
+* [GE Z-Wave Plug-in Smart Dimmer (GE 12718)](http://products.z-wavealliance.org/products/1191)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#Troubleshooting)
+
+## Capabilities
+
+* **Switch Level** - it's defined to accept two parameters, the level and the rate of dimming
+* **Actuator** - represents that a Device has commands
+* **Indicator** - gives you the ability to set the indicator LED light on a Z-Wave switch
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Z-Wave Smart Dimmers (In-Wall, In-Wall(Toggle), Plug-In) are polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Check-in interval = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [General Z-Wave Dimmer/Switch Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200955890-Troubleshooting-GE-in-wall-switch-or-dimmer-won-t-respond-to-commands-or-automations-Z-Wave-)
+* [GE Z-Wave In-Wall Smart Dimmer (GE 12724) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200902600-GE-In-Wall-Paddle-Dimmer-Switch-GE-12724-Z-Wave-)
+* [GE Z-Wave In-Wall Smart Dimmer (Toggle) (GE 12729) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/207568463-GE-In-Wall-Smart-Toggle-Dimmer-GE-12729-Z-Wave-)
+* [GE Z-Wave Plug-in Smart Dimmer (GE 12718) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/202088474-GE-Plug-In-Smart-Dimmer-GE-12718-Z-Wave-)

devicetypes/smartthings/dimmer-switch.src/dimmer-switch.groovy

@@ -20,6 +20,7 @@ metadata {
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
+		capability "Health Check"
 
 		fingerprint mfr:"0063", prod:"4457", deviceJoinName: "Z-Wave Wall Dimmer"
 		fingerprint mfr:"0063", prod:"4944", deviceJoinName: "Z-Wave Wall Dimmer"
@@ -82,6 +83,8 @@ metadata {
 }
 
 def updated(){
+	// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
   switch (ledIndicator) {
         case "on":
             indicatorWhenOn()
@@ -215,6 +218,13 @@ def poll() {
 	zwave.switchMultilevelV1.switchMultilevelGet().format()
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	log.debug "refresh() is called"
 	def commands = []

devicetypes/smartthings/ecobee-sensor.src/ecobee-sensor.groovy

@@ -67,6 +67,6 @@ def refresh() {
 
 void poll() {
 	log.debug "Executing 'poll' using parent SmartApp"
-	parent.poll()
+	parent.pollChild()
 
 }

devicetypes/smartthings/ecobee-thermostat.src/ecobee-thermostat.groovy

@@ -31,13 +31,13 @@ metadata {
 		command "switchMode"
 		command "switchFanMode"
 
-		attribute "thermostatSetpoint","number"
-		attribute "thermostatStatus","string"
+		attribute "thermostatSetpoint", "number"
+		attribute "thermostatStatus", "string"
 		attribute "maxHeatingSetpoint", "number"
 		attribute "minHeatingSetpoint", "number"
 		attribute "maxCoolingSetpoint", "number"
 		attribute "minCoolingSetpoint", "number"
-		attribute "deviceTemperatureUnit", "number"
+		attribute "deviceTemperatureUnit", "string"
 	}
 
 	tiles {
@@ -133,7 +133,7 @@ def refresh() {
 
 void poll() {
 	log.debug "Executing 'poll' using parent SmartApp"
-	parent.poll()
+	parent.pollChild()
 }
 
 def generateEvent(Map results) {
@@ -148,14 +148,12 @@ def generateEvent(Map results) {
 						 handlerName: name]
 
 			if (name=="temperature" || name=="heatingSetpoint" || name=="coolingSetpoint" ) {
-				def sendValue = convertTemperatureIfNeeded(value.toDouble(), "F", 1) //API return temperature value in F
-				sendValue =  location.temperatureScale == "C"? roundC(sendValue) : sendValue
+				def sendValue =  location.temperatureScale == "C"? roundC(convertFtoC(value.toDouble())) : value.toInteger()
 				isChange = isTemperatureStateChange(device, name, value.toString())
 				isDisplayed = isChange
 				event << [value: sendValue, unit: temperatureScale, isStateChange: isChange, displayed: isDisplayed]
 			}  else if (name=="maxCoolingSetpoint" || name=="minCoolingSetpoint" || name=="maxHeatingSetpoint" || name=="minHeatingSetpoint") {
-				def sendValue = convertTemperatureIfNeeded(value.toDouble(), "F", 1) //API return temperature value in F
-				sendValue =  location.temperatureScale == "C"? roundC(sendValue) : sendValue
+				def sendValue =  location.temperatureScale == "C"? roundC(convertFtoC(value.toDouble())) : value.toInteger()
 				event << [value: sendValue, unit: temperatureScale, displayed: false]
 			}  else if (name=="heatMode" || name=="coolMode" || name=="autoMode" || name=="auxHeatMode"){
 				isChange = isStateChange(device, name, value.toString())
@@ -253,7 +251,6 @@ void setCoolingSetpoint(setpoint) {
 	def maxCoolingSetpoint = device.currentValue("maxCoolingSetpoint")
 	def minCoolingSetpoint = device.currentValue("minCoolingSetpoint")
 
-
 	if (coolingSetpoint > maxCoolingSetpoint) {
 		coolingSetpoint = maxCoolingSetpoint
 	} else if (coolingSetpoint < minCoolingSetpoint) {
@@ -283,7 +280,6 @@ void setCoolingSetpoint(setpoint) {
 }
 
 void resumeProgram() {
-
 	log.debug "resumeProgram() is called"
 	sendEvent("name":"thermostatStatus", "value":"resuming schedule", "description":statusText, displayed: false)
 	def deviceId = device.deviceNetworkId.split(/\./).last()
@@ -354,7 +350,6 @@ def switchFanMode() {
 }
 
 def switchToFanMode(nextMode) {
-
 	log.debug "switching to fan mode: $nextMode"
 	def returnCommand
 
@@ -520,63 +515,56 @@ def fanAuto() {
 }
 
 def generateSetpointEvent() {
-
 	log.debug "Generate SetPoint Event"
 
 	def mode = device.currentValue("thermostatMode")
-	log.debug "Current Mode = ${mode}"
 
 	def heatingSetpoint = device.currentValue("heatingSetpoint")
-	log.debug "Heating Setpoint = ${heatingSetpoint}"
-
 	def coolingSetpoint = device.currentValue("coolingSetpoint")
-	log.debug "Cooling Setpoint = ${coolingSetpoint}"
-
 	def maxHeatingSetpoint = device.currentValue("maxHeatingSetpoint")
 	def maxCoolingSetpoint = device.currentValue("maxCoolingSetpoint")
 	def minHeatingSetpoint = device.currentValue("minHeatingSetpoint")
 	def minCoolingSetpoint = device.currentValue("minCoolingSetpoint")
 
-	if(location.temperatureScale == "C")
-	{
-		maxHeatingSetpoint = roundC(maxHeatingSetpoint)
-		maxCoolingSetpoint = roundC(maxCoolingSetpoint)
-		minHeatingSetpoint = roundC(minHeatingSetpoint)
-		minCoolingSetpoint = roundC(minCoolingSetpoint)
-		heatingSetpoint = roundC(heatingSetpoint)
-		coolingSetpoint = roundC(coolingSetpoint)
+	if(location.temperatureScale == "C") {
+		maxHeatingSetpoint = maxHeatingSetpoint > 40 ? roundC(convertFtoC(maxHeatingSetpoint)) : roundC(maxHeatingSetpoint)
+		maxCoolingSetpoint = maxCoolingSetpoint > 40 ? roundC(convertFtoC(maxCoolingSetpoint)) : roundC(maxCoolingSetpoint)
+		minHeatingSetpoint = minHeatingSetpoint > 40 ? roundC(convertFtoC(minHeatingSetpoint)) : roundC(minHeatingSetpoint)
+		minCoolingSetpoint = minCoolingSetpoint > 40 ? roundC(convertFtoC(minCoolingSetpoint)) : roundC(minCoolingSetpoint)
+		heatingSetpoint = heatingSetpoint > 40 ? roundC(convertFtoC(heatingSetpoint)) : roundC(heatingSetpoint)
+		coolingSetpoint = coolingSetpoint > 40 ? roundC(convertFtoC(coolingSetpoint)) : roundC(coolingSetpoint)
+	} else {
+		maxHeatingSetpoint = maxHeatingSetpoint < 40 ? roundC(convertCtoF(maxHeatingSetpoint)) : maxHeatingSetpoint
+		maxCoolingSetpoint = maxCoolingSetpoint < 40 ? roundC(convertCtoF(maxCoolingSetpoint)) : maxCoolingSetpoint
+		minHeatingSetpoint = minHeatingSetpoint < 40 ? roundC(convertCtoF(minHeatingSetpoint)) : minHeatingSetpoint
+		minCoolingSetpoint = minCoolingSetpoint < 40 ? roundC(convertCtoF(minCoolingSetpoint)) : minCoolingSetpoint
+		heatingSetpoint = heatingSetpoint < 40 ? roundC(convertCtoF(heatingSetpoint)) : heatingSetpoint
+		coolingSetpoint = coolingSetpoint < 40 ? roundC(convertCtoF(coolingSetpoint)) : coolingSetpoint
 	}
 
+	log.debug "Current Mode = ${mode}"
+	log.debug "Heating Setpoint = ${heatingSetpoint}"
+	log.debug "Cooling Setpoint = ${coolingSetpoint}"
 
 	sendEvent("name":"maxHeatingSetpoint", "value":maxHeatingSetpoint, "unit":location.temperatureScale)
 	sendEvent("name":"maxCoolingSetpoint", "value":maxCoolingSetpoint, "unit":location.temperatureScale)
 	sendEvent("name":"minHeatingSetpoint", "value":minHeatingSetpoint, "unit":location.temperatureScale)
 	sendEvent("name":"minCoolingSetpoint", "value":minCoolingSetpoint, "unit":location.temperatureScale)
-
+	sendEvent("name":"heatingSetpoint", "value":heatingSetpoint, "unit":location.temperatureScale)
+	sendEvent("name":"coolingSetpoint", "value":coolingSetpoint, "unit":location.temperatureScale)
 
 	if (mode == "heat") {
-
 		sendEvent("name":"thermostatSetpoint", "value":heatingSetpoint, "unit":location.temperatureScale)
-
 	}
 	else if (mode == "cool") {
-
 		sendEvent("name":"thermostatSetpoint", "value":coolingSetpoint, "unit":location.temperatureScale)
-
 	} else if (mode == "auto") {
-
 		sendEvent("name":"thermostatSetpoint", "value":"Auto")
-
 	} else if (mode == "off") {
-
 		sendEvent("name":"thermostatSetpoint", "value":"Off")
-
 	} else if (mode == "auxHeatOnly") {
-
 		sendEvent("name":"thermostatSetpoint", "value":heatingSetpoint, "unit":location.temperatureScale)
-
 	}
-
 }
 
 void raiseSetpoint() {
@@ -585,21 +573,31 @@ void raiseSetpoint() {
 	def maxHeatingSetpoint = device.currentValue("maxHeatingSetpoint")
 	def maxCoolingSetpoint = device.currentValue("maxCoolingSetpoint")
 
-
 	if (mode == "off" || mode == "auto") {
 		log.warn "this mode: $mode does not allow raiseSetpoint"
 	} else {
+
 		def heatingSetpoint = device.currentValue("heatingSetpoint")
 		def coolingSetpoint = device.currentValue("coolingSetpoint")
 		def thermostatSetpoint = device.currentValue("thermostatSetpoint")
+
+		if (location.temperatureScale == "C") {
+			maxHeatingSetpoint = maxHeatingSetpoint > 40 ? convertFtoC(maxHeatingSetpoint) : maxHeatingSetpoint
+			maxCoolingSetpoint = maxCoolingSetpoint > 40 ? convertFtoC(maxCoolingSetpoint) : maxCoolingSetpoint
+			heatingSetpoint = heatingSetpoint > 40 ? convertFtoC(heatingSetpoint) : heatingSetpoint
+			coolingSetpoint = coolingSetpoint > 40 ? convertFtoC(coolingSetpoint) : coolingSetpoint
+			thermostatSetpoint = thermostatSetpoint > 40 ? convertFtoC(thermostatSetpoint) : thermostatSetpoint
+		} else {
+			maxHeatingSetpoint = maxHeatingSetpoint < 40 ? convertCtoF(maxHeatingSetpoint) : maxHeatingSetpoint
+			maxCoolingSetpoint = maxCoolingSetpoint < 40 ? convertCtoF(maxCoolingSetpoint) : maxCoolingSetpoint
+			heatingSetpoint = heatingSetpoint < 40 ? convertCtoF(heatingSetpoint) : heatingSetpoint
+			coolingSetpoint = coolingSetpoint < 40 ? convertCtoF(coolingSetpoint) : coolingSetpoint
+			thermostatSetpoint = thermostatSetpoint < 40 ? convertCtoF(thermostatSetpoint) : thermostatSetpoint
+		}
+
 		log.debug "raiseSetpoint() mode = ${mode}, heatingSetpoint: ${heatingSetpoint}, coolingSetpoint:${coolingSetpoint}, thermostatSetpoint:${thermostatSetpoint}"
 
-		if (device.latestState('thermostatSetpoint')) {
-			targetvalue = device.latestState('thermostatSetpoint').value
-			targetvalue = location.temperatureScale == "F"? targetvalue.toInteger() : targetvalue.toDouble()
-		} else {
-			targetvalue = 0
-		}
+		targetvalue = thermostatSetpoint ? thermostatSetpoint : 0
 		targetvalue = location.temperatureScale == "F"? targetvalue + 1 : targetvalue + 0.5
 
 		if ((mode == "heat" || mode == "auxHeatOnly") && targetvalue > maxHeatingSetpoint) {
@@ -622,20 +620,29 @@ void lowerSetpoint() {
 	def minHeatingSetpoint = device.currentValue("minHeatingSetpoint")
 	def minCoolingSetpoint = device.currentValue("minCoolingSetpoint")
 
-
 	if (mode == "off" || mode == "auto") {
 		log.warn "this mode: $mode does not allow lowerSetpoint"
 	} else {
 		def heatingSetpoint = device.currentValue("heatingSetpoint")
 		def coolingSetpoint = device.currentValue("coolingSetpoint")
 		def thermostatSetpoint = device.currentValue("thermostatSetpoint")
-		log.debug "lowerSetpoint() mode = ${mode}, heatingSetpoint: ${heatingSetpoint}, coolingSetpoint:${coolingSetpoint}, thermostatSetpoint:${thermostatSetpoint}"
-		if (device.latestState('thermostatSetpoint')) {
-			targetvalue = device.latestState('thermostatSetpoint').value
-			targetvalue = location.temperatureScale == "F"? targetvalue.toInteger() : targetvalue.toDouble()
+
+		if (location.temperatureScale == "C") {
+			minHeatingSetpoint = minHeatingSetpoint > 40 ? convertFtoC(minHeatingSetpoint) : minHeatingSetpoint
+			minCoolingSetpoint = minCoolingSetpoint > 40 ? convertFtoC(minCoolingSetpoint) : minCoolingSetpoint
+			heatingSetpoint = heatingSetpoint > 40 ? convertFtoC(heatingSetpoint) : heatingSetpoint
+			coolingSetpoint = coolingSetpoint > 40 ? convertFtoC(coolingSetpoint) : coolingSetpoint
+			thermostatSetpoint = thermostatSetpoint > 40 ? convertFtoC(thermostatSetpoint) : thermostatSetpoint
 		} else {
-			targetvalue = 0
+			minHeatingSetpoint = minHeatingSetpoint < 40 ? convertCtoF(minHeatingSetpoint) : minHeatingSetpoint
+			minCoolingSetpoint = minCoolingSetpoint < 40 ? convertCtoF(minCoolingSetpoint) : minCoolingSetpoint
+			heatingSetpoint = heatingSetpoint < 40 ? convertCtoF(heatingSetpoint) : heatingSetpoint
+			coolingSetpoint = coolingSetpoint < 40 ? convertCtoF(coolingSetpoint) : coolingSetpoint
+			thermostatSetpoint = thermostatSetpoint < 40 ? convertCtoF(thermostatSetpoint) : thermostatSetpoint
 		}
+		log.debug "lowerSetpoint() mode = ${mode}, heatingSetpoint: ${heatingSetpoint}, coolingSetpoint:${coolingSetpoint}, thermostatSetpoint:${thermostatSetpoint}"
+
+		targetvalue = thermostatSetpoint ? thermostatSetpoint : 0
 		targetvalue = location.temperatureScale == "F"? targetvalue - 1 : targetvalue - 0.5
 
 		if ((mode == "heat" || mode == "auxHeatOnly") && targetvalue < minHeatingSetpoint) {
@@ -653,66 +660,83 @@ void lowerSetpoint() {
 
 //called by raiseSetpoint() and lowerSetpoint()
 void alterSetpoint(temp) {
-
 	def mode = device.currentValue("thermostatMode")
-	def heatingSetpoint = device.currentValue("heatingSetpoint")
-	def coolingSetpoint = device.currentValue("coolingSetpoint")
-	def deviceId = device.deviceNetworkId.split(/\./).last()
 
-	def targetHeatingSetpoint
-	def targetCoolingSetpoint
-
-	//step1: check thermostatMode, enforce limits before sending request to cloud
-	if (mode == "heat" || mode == "auxHeatOnly"){
-		if (temp.value > coolingSetpoint){
-			targetHeatingSetpoint = temp.value
-			targetCoolingSetpoint = temp.value
-		} else {
-			targetHeatingSetpoint = temp.value
-			targetCoolingSetpoint = coolingSetpoint
-		}
-	} else if (mode == "cool") {
-		//enforce limits before sending request to cloud
-		if (temp.value < heatingSetpoint){
-			targetHeatingSetpoint = temp.value
-			targetCoolingSetpoint = temp.value
-		} else {
-			targetHeatingSetpoint = heatingSetpoint
-			targetCoolingSetpoint = temp.value
-		}
-	}
-
-	log.debug "alterSetpoint >> in mode ${mode} trying to change heatingSetpoint to $targetHeatingSetpoint " +
-			"coolingSetpoint to $targetCoolingSetpoint with holdType : ${holdType}"
-
-	def sendHoldType = holdType ? (holdType=="Temporary")? "nextTransition" : (holdType=="Permanent")? "indefinite" : "indefinite" : "indefinite"
-
-	def coolingValue = location.temperatureScale == "C"? convertCtoF(targetCoolingSetpoint) : targetCoolingSetpoint
-	def heatingValue = location.temperatureScale == "C"? convertCtoF(targetHeatingSetpoint) : targetHeatingSetpoint
-
-	if (parent.setHold(heatingValue, coolingValue, deviceId, sendHoldType)) {
-		sendEvent("name": "thermostatSetpoint", "value": temp.value, displayed: false)
-		sendEvent("name": "heatingSetpoint", "value": targetHeatingSetpoint, "unit": location.temperatureScale)
-		sendEvent("name": "coolingSetpoint", "value": targetCoolingSetpoint, "unit": location.temperatureScale)
-		log.debug "alterSetpoint in mode $mode succeed change setpoint to= ${temp.value}"
+	if (mode == "off" || mode == "auto") {
+		log.warn "this mode: $mode does not allow alterSetpoint"
 	} else {
-		log.error "Error alterSetpoint()"
-		if (mode == "heat" || mode == "auxHeatOnly"){
-			sendEvent("name": "thermostatSetpoint", "value": heatingSetpoint.toString(), displayed: false)
-		} else if (mode == "cool") {
-			sendEvent("name": "thermostatSetpoint", "value": coolingSetpoint.toString(), displayed: false)
+		def heatingSetpoint = device.currentValue("heatingSetpoint")
+		def coolingSetpoint = device.currentValue("coolingSetpoint")
+		def deviceId = device.deviceNetworkId.split(/\./).last()
+
+		def targetHeatingSetpoint
+		def targetCoolingSetpoint
+
+		def temperatureScaleHasChanged = false
+
+		if (location.temperatureScale == "C") {
+			if ( heatingSetpoint > 40.0 || coolingSetpoint > 40.0 ) {
+				temperatureScaleHasChanged = true
+			}
+		} else {
+			if ( heatingSetpoint < 40.0 || coolingSetpoint < 40.0 ) {
+				temperatureScaleHasChanged = true
+			}
 		}
+
+		//step1: check thermostatMode, enforce limits before sending request to cloud
+		if (mode == "heat" || mode == "auxHeatOnly"){
+			if (temp.value > coolingSetpoint){
+				targetHeatingSetpoint = temp.value
+				targetCoolingSetpoint = temp.value
+			} else {
+				targetHeatingSetpoint = temp.value
+				targetCoolingSetpoint = coolingSetpoint
+			}
+		} else if (mode == "cool") {
+			//enforce limits before sending request to cloud
+			if (temp.value < heatingSetpoint){
+				targetHeatingSetpoint = temp.value
+				targetCoolingSetpoint = temp.value
+			} else {
+				targetHeatingSetpoint = heatingSetpoint
+				targetCoolingSetpoint = temp.value
+			}
+		}
+
+		log.debug "alterSetpoint >> in mode ${mode} trying to change heatingSetpoint to $targetHeatingSetpoint " +
+				"coolingSetpoint to $targetCoolingSetpoint with holdType : ${holdType}"
+
+		def sendHoldType = holdType ? (holdType=="Temporary")? "nextTransition" : (holdType=="Permanent")? "indefinite" : "indefinite" : "indefinite"
+
+		def coolingValue = location.temperatureScale == "C"? convertCtoF(targetCoolingSetpoint) : targetCoolingSetpoint
+		def heatingValue = location.temperatureScale == "C"? convertCtoF(targetHeatingSetpoint) : targetHeatingSetpoint
+
+		if (parent.setHold(heatingValue, coolingValue, deviceId, sendHoldType)) {
+			sendEvent("name": "thermostatSetpoint", "value": temp.value, displayed: false)
+			sendEvent("name": "heatingSetpoint", "value": targetHeatingSetpoint, "unit": location.temperatureScale)
+			sendEvent("name": "coolingSetpoint", "value": targetCoolingSetpoint, "unit": location.temperatureScale)
+			log.debug "alterSetpoint in mode $mode succeed change setpoint to= ${temp.value}"
+		} else {
+			log.error "Error alterSetpoint()"
+			if (mode == "heat" || mode == "auxHeatOnly"){
+				sendEvent("name": "thermostatSetpoint", "value": heatingSetpoint.toString(), displayed: false)
+			} else if (mode == "cool") {
+				sendEvent("name": "thermostatSetpoint", "value": coolingSetpoint.toString(), displayed: false)
+			}
+		}
+
+		if ( temperatureScaleHasChanged )
+			generateSetpointEvent()
+		generateStatusEvent()
 	}
-	generateStatusEvent()
 }
 
 def generateStatusEvent() {
-
 	def mode = device.currentValue("thermostatMode")
 	def heatingSetpoint = device.currentValue("heatingSetpoint")
 	def coolingSetpoint = device.currentValue("coolingSetpoint")
 	def temperature = device.currentValue("temperature")
-
 	def statusText
 
 	log.debug "Generate Status Event for Mode = ${mode}"
@@ -722,36 +746,25 @@ def generateStatusEvent() {
 	log.debug "HVAC Mode = ${mode}"
 
 	if (mode == "heat") {
-
 		if (temperature >= heatingSetpoint)
 			statusText = "Right Now: Idle"
 		else
 			statusText = "Heating to ${heatingSetpoint} ${location.temperatureScale}"
-
 	} else if (mode == "cool") {
-
 		if (temperature <= coolingSetpoint)
 			statusText = "Right Now: Idle"
 		else
 			statusText = "Cooling to ${coolingSetpoint} ${location.temperatureScale}"
-
 	} else if (mode == "auto") {
-
 		statusText = "Right Now: Auto"
-
 	} else if (mode == "off") {
-
 		statusText = "Right Now: Off"
-
 	} else if (mode == "auxHeatOnly") {
-
 		statusText = "Emergency Heat"
-
 	} else {
-
 		statusText = "?"
-
 	}
+
 	log.debug "Generate Status Event = ${statusText}"
 	sendEvent("name":"thermostatStatus", "value":statusText, "description":statusText, displayed: true)
 }
@@ -765,7 +778,7 @@ def roundC (tempC) {
 }
 
 def convertFtoC (tempF) {
-	return String.format("%.1f", (Math.round(((tempF - 32)*(5/9)) * 2))/2)
+	return ((Math.round(((tempF - 32)*(5/9)) * 2))/2).toDouble()
 }
 
 def convertCtoF (tempC) {

devicetypes/smartthings/hue-bloom.src/hue-bloom.groovy

@@ -57,7 +57,7 @@ metadata {
 }
 
 void installed() {
-	sendEvent(name: "checkInterval", value: 60 * 15, data: [protocol: "lan"], displayed: false)
+	sendEvent(name: "DeviceWatch-Enroll", value: "{\"protocol\": \"LAN\", \"scheme\":\"untracked\", \"hubHardwareId\": \"${device.hub.hardwareID}\"}")
 }
 
 // parse events into attributes
@@ -172,6 +172,3 @@ def verifyPercent(percent) {
     }
 }
 
-def ping() {
-    log.debug "${parent.ping(this)}"
-}

devicetypes/smartthings/hue-bridge.src/hue-bridge.groovy

@@ -7,9 +7,11 @@
 metadata {
 	// Automatically generated. Make future change here.
 	definition (name: "Hue Bridge", namespace: "smartthings", author: "SmartThings") {
+		capability "Health Check"
+
 		attribute "networkAddress", "string"
-        // Used to indicate if bridge is reachable or not, i.e. is the bridge connected to the network
-        // Possible values "Online" or "Offline"
+		// Used to indicate if bridge is reachable or not, i.e. is the bridge connected to the network
+		// Possible values "Online" or "Offline"
 		attribute "status", "string"
 		// Id is the number on the back of the hub, Hue uses last six digits of Mac address
 		// This is also used in the Hue application as ID
@@ -42,6 +44,10 @@ metadata {
 	}
 }
 
+void installed() {
+	sendEvent(name: "DeviceWatch-Enroll", value: "{\"protocol\": \"LAN\", \"scheme\":\"untracked\", \"hubHardwareId\": \"${device.hub.hardwareID}\"}")
+}
+
 // parse events into attributes
 def parse(description) {
 	log.debug "Parsing '${description}'"
@@ -70,13 +76,8 @@ def parse(description) {
 					def bulbs = new groovy.json.JsonSlurper().parseText(msg.body)
 					if (bulbs.state) {
 						log.info "Bridge response: $msg.body"
-					} else {
-						// Sending Bulbs List to parent"
-						if (parent.isInBulbDiscovery())
-							log.info parent.bulbListHandler(device.hub.id, msg.body)
 					}
-				}
-				else if (contentType?.contains("xml")) {
+				} else if (contentType?.contains("xml")) {
 					log.debug "HUE BRIDGE ALREADY PRESENT"
 					parent.hubVerification(device.hub.id, msg.body)
 				}
@@ -85,3 +86,4 @@ def parse(description) {
 	}
 	results
 }
+

devicetypes/smartthings/hue-bulb.src/hue-bulb.groovy

@@ -66,7 +66,7 @@ metadata {
 }
 
 void installed() {
-	sendEvent(name: "checkInterval", value: 60 * 15, data: [protocol: "lan"], displayed: false)
+	sendEvent(name: "DeviceWatch-Enroll", value: "{\"protocol\": \"LAN\", \"scheme\":\"untracked\", \"hubHardwareId\": \"${device.hub.hardwareID}\"}")
 }
 
 // parse events into attributes
@@ -174,7 +174,7 @@ void setColorTemperature(value) {
 
 void refresh() {
     log.debug "Executing 'refresh'"
-    parent.manualRefresh()
+    parent?.manualRefresh()
 }
 
 def verifyPercent(percent) {
@@ -188,6 +188,3 @@ def verifyPercent(percent) {
     }
 }
 
-def ping() {
-    log.trace "${parent.ping(this)}"
-}

devicetypes/smartthings/hue-lux-bulb.src/hue-lux-bulb.groovy

@@ -50,7 +50,7 @@ metadata {
 }
 
 void installed() {
-	sendEvent(name: "checkInterval", value: 60 * 15, data: [protocol: "lan"], displayed: false)
+	sendEvent(name: "DeviceWatch-Enroll", value: "{\"protocol\": \"LAN\", \"scheme\":\"untracked\", \"hubHardwareId\": \"${device.hub.hardwareID}\"}")
 }
 
 // parse events into attributes
@@ -93,6 +93,3 @@ void refresh() {
 	parent.manualRefresh()
 }
 
-def ping() {
-    log.debug "${parent.ping(this)}"
-}

devicetypes/smartthings/hue-white-ambiance-bulb.src/hue-white-ambiance-bulb.groovy

@@ -55,7 +55,7 @@ metadata {
 }
 
 void installed() {
-	sendEvent(name: "checkInterval", value: 60 * 15, data: [protocol: "lan"], displayed: false)
+	sendEvent(name: "DeviceWatch-Enroll", value: "{\"protocol\": \"LAN\", \"scheme\":\"untracked\", \"hubHardwareId\": \"${device.hub.hardwareID}\"}")
 }
 
 // parse events into attributes
@@ -107,6 +107,3 @@ void refresh() {
     parent.manualRefresh()
 }
 
-def ping() {
-    log.debug "${parent.ping(this)}"
-}

devicetypes/smartthings/lifx-color-bulb.src/lifx-color-bulb.groovy

@@ -11,9 +11,9 @@ metadata {
 		capability "Color Temperature"
 		capability "Switch"
 		capability "Switch Level" // brightness
-		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
+		capability "Health Check"
 	}
 
 	simulator {
@@ -23,7 +23,6 @@ metadata {
 	tiles(scale: 2) {
 		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
 			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-				attributeState "unreachable", label: "?", action:"refresh.refresh", icon:"http://hosted.lifx.co/smartthings/v1/196xUnreachable.png", backgroundColor:"#666666"
 				attributeState "on", label:'${name}', action:"switch.off", icon:"http://hosted.lifx.co/smartthings/v1/196xOn.png", backgroundColor:"#79b821", nextState:"turningOff"
 				attributeState "off", label:'${name}', action:"switch.on", icon:"http://hosted.lifx.co/smartthings/v1/196xOff.png", backgroundColor:"#ffffff", nextState:"turningOn"
 				attributeState "turningOn", label:'Turning on', action:"switch.off", icon:"http://hosted.lifx.co/smartthings/v1/196xOn.png", backgroundColor:"#79b821", nextState:"turningOff"
@@ -64,12 +63,8 @@ metadata {
 	}
 }
 
-// parse events into attributes
-def parse(String description) {
-	if (description == 'updated') {
-		return // don't poll when config settings is being updated as it may time out
-	}
-	poll()
+void installed() {
+	sendEvent(name: "DeviceWatch-Enroll", value: "{\"protocol\": \"cloud\", \"scheme\":\"untracked\", \"hubHardwareId\": \"${device?.hub?.hardwareID}\"}")
 }
 
 // handle commands
@@ -141,7 +136,6 @@ def setLevel(percentage) {
 		percentage = 1 // clamp to 1%
 	}
 	if (percentage == 0) {
-		sendEvent(name: "level", value: 0) // Otherwise the level value tile does not update
 		return off() // if the brightness is set to 0, just turn it off
 	}
 	parent.logErrors(logObject:log) {
@@ -193,14 +187,17 @@ def off() {
 	return []
 }
 
-def poll() {
-	log.debug "Executing 'poll' for ${device} ${this} ${device.deviceNetworkId}"
+def refresh() {
+	log.debug "Executing 'refresh'"
+	
 	def resp = parent.apiGET("/lights/${selector()}")
 	if (resp.status == 404) {
-		sendEvent(name: "switch", value: "unreachable")
+		state.online = false
+		sendEvent(name: "DeviceWatch-DeviceStatusUpdate", value: "offline", displayed: false)
+ 		log.warn "$device is Offline"
 		return []
 	} else if (resp.status != 200) {
-		log.error("Unexpected result in poll(): [${resp.status}] ${resp.data}")
+		log.error("Unexpected result in refresh(): [${resp.status}] ${resp.data}")
 		return []
 	}
 	def data = resp.data[0]
@@ -209,19 +206,20 @@ def poll() {
 	sendEvent(name: "label", value: data.label)
 	sendEvent(name: "level", value: Math.round((data.brightness ?: 1) * 100))
 	sendEvent(name: "switch.setLevel", value: Math.round((data.brightness ?: 1) * 100))
-	sendEvent(name: "switch", value: data.connected ? data.power : "unreachable")
+	sendEvent(name: "switch", value: data.power)
 	sendEvent(name: "color", value: colorUtil.hslToHex((data.color.hue / 3.6) as int, (data.color.saturation * 100) as int))
 	sendEvent(name: "hue", value: data.color.hue / 3.6)
 	sendEvent(name: "saturation", value: data.color.saturation * 100)
 	sendEvent(name: "colorTemperature", value: data.color.kelvin)
-	sendEvent(name: "model", value: "${data.product.company} ${data.product.name}")
+	sendEvent(name: "model", value: data.product.name)
 
-	return []
+	if (data.connected) {
+		sendEvent(name: "DeviceWatch-DeviceStatus", value: "online", displayed: false)
+		log.debug "$device is Online"
+	} else {
+		sendEvent(name: "DeviceWatch-DeviceStatus", value: "offline", displayed: false)
+		log.warn "$device is Offline"
 }
-
-def refresh() {
-	log.debug "Executing 'refresh'"
-	poll()
 }
 
 def selector() {

devicetypes/smartthings/lifx-white-bulb.src/lifx-white-bulb.groovy

@@ -10,9 +10,9 @@ metadata {
 		capability "Color Temperature"
 		capability "Switch"
 		capability "Switch Level" // brightness
-		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
+		capability "Health Check"
 	}
 
 	simulator {
@@ -22,13 +22,12 @@ metadata {
 	tiles(scale: 2) {
 		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
 			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
-				attributeState "unreachable", label: "?", action:"refresh.refresh", icon:"http://hosted.lifx.co/smartthings/v1/196xUnreachable.png", backgroundColor:"#666666"
 				attributeState "on", label:'${name}', action:"switch.off", icon:"http://hosted.lifx.co/smartthings/v1/196xOn.png", backgroundColor:"#79b821", nextState:"turningOff"
 				attributeState "off", label:'${name}', action:"switch.on", icon:"http://hosted.lifx.co/smartthings/v1/196xOff.png", backgroundColor:"#ffffff", nextState:"turningOn"
 				attributeState "turningOn", label:'Turning on', action:"switch.off", icon:"http://hosted.lifx.co/smartthings/v1/196xOn.png", backgroundColor:"#79b821", nextState:"turningOff"
 				attributeState "turningOff", label:'Turning off', action:"switch.on", icon:"http://hosted.lifx.co/smartthings/v1/196xOff.png", backgroundColor:"#ffffff", nextState:"turningOn"
-
 			}
+
 			tileAttribute ("device.level", key: "SLIDER_CONTROL") {
 				attributeState "level", action:"switch level.setLevel"
 			}
@@ -53,15 +52,10 @@ metadata {
 		main "switch"
 		details(["switch", "colorTempSliderControl", "colorTemp", "refresh"])
 	}
-
 }
 
-// parse events into attributes
-def parse(String description) {
-	if (description == 'updated') {
-		return // don't poll when config settings is being updated as it may time out
-	}
-	poll()
+void installed() {
+	sendEvent(name: "DeviceWatch-Enroll", value: "{\"protocol\": \"cloud\", \"scheme\":\"untracked\", \"hubHardwareId\": \"${device?.hub?.hardwareID}\"}")
 }
 
 // handle commands
@@ -71,7 +65,6 @@ def setLevel(percentage) {
 		percentage = 1 // clamp to 1%
 	}
 	if (percentage == 0) {
-		sendEvent(name: "level", value: 0) // Otherwise the level value tile does not update
 		return off() // if the brightness is set to 0, just turn it off
 	}
 	parent.logErrors(logObject:log) {
@@ -123,14 +116,17 @@ def off() {
 	return []
 }
 
-def poll() {
-	log.debug "Executing 'poll' for ${device} ${this} ${device.deviceNetworkId}"
+def refresh() {
+	log.debug "Executing 'refresh'"
+	
 	def resp = parent.apiGET("/lights/${selector()}")
 	if (resp.status == 404) {
-		sendEvent(name: "switch", value: "unreachable")
+		state.online = false
+		sendEvent(name: "DeviceWatch-DeviceStatusUpdate", value: "offline", displayed: false)
+		log.warn "$device is Offline"
 		return []
 	} else if (resp.status != 200) {
-		log.error("Unexpected result in poll(): [${resp.status}] ${resp.data}")
+		log.error("Unexpected result in refresh(): [${resp.status}] ${resp.data}")
 		return []
 	}
 	def data = resp.data[0]
@@ -138,16 +134,17 @@ def poll() {
 	sendEvent(name: "label", value: data.label)
 	sendEvent(name: "level", value: Math.round((data.brightness ?: 1) * 100))
 	sendEvent(name: "switch.setLevel", value: Math.round((data.brightness ?: 1) * 100))
-	sendEvent(name: "switch", value: data.connected ? data.power : "unreachable")
+	sendEvent(name: "switch", value: data.power)
 	sendEvent(name: "colorTemperature", value: data.color.kelvin)
 	sendEvent(name: "model", value: data.product.name)
 
-	return []
-}
-
-def refresh() {
-	log.debug "Executing 'refresh'"
-	poll()
+	if (data.connected) {
+		sendEvent(name: "DeviceWatch-DeviceStatus", value: "online", displayed: false)
+		log.debug "$device is Online"
+	} else {
+		sendEvent(name: "DeviceWatch-DeviceStatus", value: "offline", displayed: false)
+		log.warn "$device is Offline"
+	}
 }
 
 def selector() {

devicetypes/smartthings/nyce-open-closed-sensor.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/nyce-open-closed-sensor.src/README.md

@@ -0,0 +1,37 @@
+# Nyce Door/Window Sensor (Open/Close Sensor)
+
+
+
+Works with:
+
+* [NYCE Door/Window Sensor NCZ-3011](https://support.smartthings.com/hc/en-us/articles/204576764-NYCE-Door-Window-Sensor)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Contact Sensor** - can detect contact (with possible values - open/closed)
+* **Battery** - defines device uses a battery
+* **Refresh** - _refresh()_ command for status updates
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+A Category C2 Nyce Door/Window sensor that has 12min check-in interval
+
+## Battery Specification
+
+One 3V CR2032 battery required.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the sensor is out of range.
+Pairing needs to be tried again by placing the sensor closer to the hub.
+Instructions related to pairing, resetting and removing the sensor from SmartThings can be found in the following link:
+* [Nyce Door/Window Sensor](https://support.smartthings.com/hc/en-us/articles/204576764-NYCE-Door-Window-Sensor)

devicetypes/smartthings/nyce-open-closed-sensor.src/nyce-open-closed-sensor.groovy

@@ -19,25 +19,26 @@ import physicalgraph.zigbee.clusters.iaszone.ZoneStatus
 
 metadata {
 	definition (name: "NYCE Open/Closed Sensor", namespace: "smartthings", author: "NYCE") {
-    	capability "Battery"
+		capability "Battery"
 		capability "Configuration"
-        capability "Contact Sensor"
+		capability "Contact Sensor"
 		capability "Refresh"
-        
-        command "enrollResponse"
- 
- 
- 		fingerprint inClusters: "0000,0001,0003,0500,0020", manufacturer: "NYCE", model: "3010", deviceJoinName: "NYCE Door Hinge Sensor"
+		capability "Health Check"
+
+		command "enrollResponse"
+
+
+		fingerprint inClusters: "0000,0001,0003,0500,0020", manufacturer: "NYCE", model: "3010", deviceJoinName: "NYCE Door Hinge Sensor"
 		fingerprint inClusters: "0000,0001,0003,0406,0500,0020", manufacturer: "NYCE", model: "3011", deviceJoinName: "NYCE Door/Window Sensor"
-        fingerprint inClusters: "0000,0001,0003,0500,0020", manufacturer: "NYCE", model: "3011", deviceJoinName: "NYCE Door/Window Sensor"
-        fingerprint inClusters: "0000,0001,0003,0406,0500,0020", manufacturer: "NYCE", model: "3014", deviceJoinName: "NYCE Tilt Sensor"
-        fingerprint inClusters: "0000,0001,0003,0500,0020", manufacturer: "NYCE", model: "3014", deviceJoinName: "NYCE Tilt Sensor"
+		fingerprint inClusters: "0000,0001,0003,0500,0020", manufacturer: "NYCE", model: "3011", deviceJoinName: "NYCE Door/Window Sensor"
+		fingerprint inClusters: "0000,0001,0003,0406,0500,0020", manufacturer: "NYCE", model: "3014", deviceJoinName: "NYCE Tilt Sensor"
+		fingerprint inClusters: "0000,0001,0003,0500,0020", manufacturer: "NYCE", model: "3014", deviceJoinName: "NYCE Tilt Sensor"
 	}
- 
+
 	simulator {
- 
+
 	}
- 
+
 	tiles {
 		standardTile("contact", "device.contact", width: 2, height: 2) {
 			state("open", label:'${name}', icon:"st.contact.contact.open", backgroundColor:"#ffa81e")
@@ -273,23 +274,28 @@ private List parseIasMessage(String description) {
 	return resultListMap
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	return zigbee.readAttribute(0x001, 0x0020) // Read the Battery Level
+}
+
 def configure() {
+	// Device-Watch allows 2 check-in misses from device
+	sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+
 	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
 
-	def configCmds = [
-			//battery reporting and heartbeat
-			"zdo bind 0x${device.deviceNetworkId} 1 ${endpointId} 1 {${device.zigbeeId}} {}", "delay 200",
-			"zcl global send-me-a-report 1 0x20 0x20 600 3600 {01}", "delay 200",
-			"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 1500",
-
-
+	def enrollCmds = [
 			// Writes CIE attribute on end device to direct reports to the hub's EUID
 			"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
 			"send 0x${device.deviceNetworkId} 1 1", "delay 500",
 	]
 
 	log.debug "configure: Write IAS CIE"
-	return configCmds
+	// battery minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
+	return enrollCmds + zigbee.batteryConfig(30, 300) + refresh() // send refresh cmds as part of config
 }
 
 def enrollResponse() {
@@ -334,7 +340,8 @@ Integer convertHexToInt(hex) {
 
 def refresh() {
 	log.debug "Refreshing Battery"
-	[
+	def refreshCmds = [
 			"st rattr 0x${device.deviceNetworkId} ${endpointId} 1 0x20", "delay 200"
 	]
+	return refreshCmds + enrollResponse()
 }

devicetypes/smartthings/osram-lightify-gardenspot-mini-rgb.src/osram-lightify-gardenspot-mini-rgb.groovy

@@ -21,9 +21,6 @@ metadata {
         attribute "colorName", "string"
 
         command "setAdjustedColor"
-
-        fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Gardenspot RGB"
-		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY Gardenspot RGB"
     }
 
     // simulator metadata

devicetypes/smartthings/smartpower-dimming-outlet.src/smartpower-dimming-outlet.groovy

@@ -133,7 +133,7 @@ def refresh() {
 }
 
 def configure() {
-	onOffConfig() + levelConfig() + powerConfig() + refresh()
+	refresh() + onOffConfig() + levelConfig() + powerConfig()
 }
 
 

devicetypes/smartthings/smartpower-outlet-v1.src/smartpower-outlet-v1.groovy

@@ -47,9 +47,21 @@ def parse(String description) {
 
 // Commands to device
 def on() {
-	'zcl on-off on'
+	[
+			'zcl on-off on',
+			'delay 200',
+			"send 0x${zigbee.deviceNetworkId} 0x01 0x${zigbee.endpointId}",
+			'delay 500'
+
+	]
+
 }
 
 def off() {
-	'zcl on-off off'
+	[
+			'zcl on-off off',
+			'delay 200',
+			"send 0x${zigbee.deviceNetworkId} 0x01 0x${zigbee.endpointId}",
+			'delay 500'
+	]
 }

devicetypes/smartthings/smartpower-outlet.src/README.md

@@ -23,10 +23,10 @@ Works with:
 
 ## Device Health
 
-A Category C1 smart power outlet with maxReportTime of 10 min.
-Check-in interval is double the value of maxReportTime for Zigbee device. 
+A Category C1 smart power outlet with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime. 
 This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 2*10 = 20 min
+Check-in interval = 12 mins
 
 ## Troubleshooting
 

devicetypes/smartthings/smartpower-outlet.src/smartpower-outlet.groovy

@@ -16,7 +16,7 @@
 
 metadata {
 	// Automatically generated. Make future change here.
-	definition (name: "SmartPower Outlet", namespace: "smartthings", author: "SmartThings", category: "C1") {
+	definition (name: "SmartPower Outlet", namespace: "smartthings", author: "SmartThings") {
 		capability "Actuator"
 		capability "Switch"
 		capability "Power Meter"
@@ -74,6 +74,15 @@ metadata {
 	}
 }
 
+def installed() {
+	log.debug "${device} installed"
+}
+
+def updated() {
+	log.debug "${device} updated"
+	configureHealthCheck()
+}
+
 // Parse incoming device messages to generate events
 def parse(String description) {
 	log.debug "description is $description"
@@ -104,8 +113,21 @@ def parse(String description) {
 		}
 	}
 	else {
-		log.warn "DID NOT PARSE MESSAGE for description : $description"
-		log.debug zigbee.parseDescriptionAsMap(description)
+		def cluster = zigbee.parse(description)
+
+		if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07){
+			if (cluster.data[0] == 0x00) {
+				log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
+				sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+			}
+			else {
+				log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+			}
+		}
+		else {
+			log.warn "DID NOT PARSE MESSAGE for description : $description"
+			log.debug "${cluster}"
+		}
 	}
 }
 
@@ -127,11 +149,17 @@ def refresh() {
 	zigbee.onOffRefresh() + zigbee.electricMeasurementPowerRefresh()
 }
 
+def configureHealthCheck() {
+	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// enrolls with default periodic reporting until newer 5 min interval is confirmed
+	sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+}
+
 def configure() {
-	// Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-	sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
+
+
 	// OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-	zigbee.onOffConfig(0, 300) + powerConfig() + refresh()
+	refresh() + zigbee.onOffConfig(0, 300) + powerConfig()
 }
 
 //power config for devices with min reporting interval as 1 seconds and reporting interval if no activity as 10min (600s)

devicetypes/smartthings/smartsense-moisture-sensor.src/README.md

@@ -23,10 +23,10 @@ Works with:
 
 ## Device Health
 
-A Category C2 moisture sensor with maxReportTime of 1 hr.
-Check-in interval is double the value of maxReportTime for Zigbee device. 
+A Category C2 moisture sensor with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime. 
 This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 2*60 = 120 min
+Check-in interval = 12 mins
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-moisture-sensor.src/smartsense-moisture-sensor.groovy

@@ -17,7 +17,7 @@ import physicalgraph.zigbee.clusters.iaszone.ZoneStatus
 
 
 metadata {
-	definition (name: "SmartSense Moisture Sensor",namespace: "smartthings", author: "SmartThings", category: "C2") {
+	definition (name: "SmartSense Moisture Sensor",namespace: "smartthings", author: "SmartThings") {
 		capability "Configuration"
 		capability "Battery"
 		capability "Refresh"
@@ -84,6 +84,15 @@ metadata {
 	}
 }
 
+def installed() {
+	log.debug "${device} installed"
+}
+
+def updated() {
+	log.debug "${device} updated"
+	configureHealthCheck()
+}
+
 def parse(String description) {
 	log.debug "description: $description"
 
@@ -118,14 +127,28 @@ private Map parseCatchAllMessage(String description) {
 	if (shouldProcessMessage(cluster)) {
 		switch(cluster.clusterId) {
 			case 0x0001:
-				resultMap = getBatteryResult(cluster.data.last())
+				// 0x07 - configure reporting
+				if (cluster.command != 0x07) {
+					resultMap = getBatteryResult(cluster.data.last())
+				}
 				break
 
             case 0x0402:
-                // temp is last 2 data values. reverse to swap endian
-                String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
-                def value = getTemperature(temp)
-                resultMap = getTemperatureResult(value)
+				if (cluster.command == 0x07) {
+					if (cluster.data[0] == 0x00){
+						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
+						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+					}
+					else {
+						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+					}
+				}
+				else {
+					// temp is last 2 data values. reverse to swap endian
+					String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
+					def value = getTemperature(temp)
+					resultMap = getTemperatureResult(value)
+				}
                 break
         }
     }
@@ -135,10 +158,8 @@ private Map parseCatchAllMessage(String description) {
 
 private boolean shouldProcessMessage(cluster) {
 	// 0x0B is default response indicating message got through
-	// 0x07 is bind message
 	boolean ignoredMessage = cluster.profileId != 0x0104 ||
 		cluster.command == 0x0B ||
-		cluster.command == 0x07 ||
 		(cluster.data.size() > 0 && cluster.data.first() == 0x3e)
 	return !ignoredMessage
 }
@@ -180,9 +201,9 @@ private Map parseIasMessage(String description) {
 def getTemperature(value) {
 	def celsius = Integer.parseInt(value, 16).shortValue() / 100
 	if(getTemperatureScale() == "C"){
-		return celsius
+		return Math.round(celsius)
 	} else {
-		return celsiusToFahrenheit(celsius) as Integer
+		return Math.round(celsiusToFahrenheit(celsius))
 	}
 }
 
@@ -291,20 +312,16 @@ def refresh() {
 	return refreshCmds + enrollResponse()
 }
 
+def configureHealthCheck() {
+	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// enrolls with default periodic reporting until newer 5 min interval is confirmed
+	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+}
+
 def configure() {
-	// Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-	sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
-
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
-	log.debug "Configuring Reporting, IAS CIE, and Bindings."
-	def enrollCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 1", "delay 500",
-	]
-
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	return enrollCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) + refresh() // send refresh cmds as part of config
+	return refresh() + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-motion-sensor.src/README.md

@@ -22,10 +22,10 @@ Works with:
 
 ## Device Health
 
-A Category C2 motion sensor with maxReportTime of 1 hr.
-Check-in interval is double the value of maxReportTime for Zigbee device. 
+A Category C2 motion sensor with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime.
 This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 2*60 = 120 min
+Check-in interval = 12 mins
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-motion-sensor.src/smartsense-motion-sensor.groovy

@@ -17,7 +17,7 @@ import physicalgraph.zigbee.clusters.iaszone.ZoneStatus
 
 
 metadata {
-	definition (name: "SmartSense Motion Sensor", namespace: "smartthings", author: "SmartThings", category: "C2") {
+	definition (name: "SmartSense Motion Sensor", namespace: "smartthings", author: "SmartThings") {
 		capability "Motion Sensor"
 		capability "Configuration"
 		capability "Battery"
@@ -88,6 +88,15 @@ metadata {
 	}
 }
 
+def installed() {
+	log.debug "${device} installed"
+}
+
+def updated() {
+	log.debug "${device} updated"
+	configureHealthCheck()
+}
+
 def parse(String description) {
 	log.debug "description: $description"
 
@@ -122,19 +131,37 @@ private Map parseCatchAllMessage(String description) {
 	if (shouldProcessMessage(cluster)) {
 		switch(cluster.clusterId) {
 			case 0x0001:
-				resultMap = getBatteryResult(cluster.data.last())
+				// 0x07 - configure reporting
+				if (cluster.command != 0x07) {
+					resultMap = getBatteryResult(cluster.data.last())
+				}
 				break
 
 			case 0x0402:
-				// temp is last 2 data values. reverse to swap endian
-				String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
-				def value = getTemperature(temp)
-				resultMap = getTemperatureResult(value)
+				if (cluster.command == 0x07) {
+					if (cluster.data[0] == 0x00) {
+						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
+						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+					}
+					else {
+						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+					}
+
+				}
+				else {
+					// temp is last 2 data values. reverse to swap endian
+					String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
+					def value = getTemperature(temp)
+					resultMap = getTemperatureResult(value)
+				}
 				break
 
 			case 0x0406:
-				log.debug 'motion'
-				resultMap.name = 'motion'
+				// 0x07 - configure reporting
+				if (cluster.command != 0x07) {
+					log.debug 'motion'
+					resultMap.name = 'motion'
+				}
 				break
 		}
 	}
@@ -144,10 +171,8 @@ private Map parseCatchAllMessage(String description) {
 
 private boolean shouldProcessMessage(cluster) {
 	// 0x0B is default response indicating message got through
-	// 0x07 is bind message
 	boolean ignoredMessage = cluster.profileId != 0x0104 ||
 		cluster.command == 0x0B ||
-		cluster.command == 0x07 ||
 		(cluster.data.size() > 0 && cluster.data.first() == 0x3e)
 	return !ignoredMessage
 }
@@ -194,9 +219,9 @@ private Map parseIasMessage(String description) {
 def getTemperature(value) {
 	def celsius = Integer.parseInt(value, 16).shortValue() / 100
 	if(getTemperatureScale() == "C"){
-		return celsius
+		return Math.round(celsius)
 	} else {
-		return celsiusToFahrenheit(celsius) as Integer
+		return Math.round(celsiusToFahrenheit(celsius))
 	}
 }
 
@@ -302,20 +327,16 @@ def refresh() {
 	return refreshCmds + enrollResponse()
 }
 
+def configureHealthCheck() {
+	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// enrolls with default periodic reporting until newer 5 min interval is confirmed
+	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+}
+
 def configure() {
-	// Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-	sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
-
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
-	log.debug "Configuring Reporting, IAS CIE, and Bindings."
-
-	def enrollCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
-	]
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	return enrollCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) + refresh() // send refresh cmds as part of config
+	return refresh() + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-motion-temp-sensor.src/smartsense-motion-temp-sensor.groovy

@@ -255,13 +255,9 @@ def refresh() {
 }
 
 def configure() {
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
 	log.debug "Configuring Reporting, IAS CIE, and Bindings."
 
 	def configCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
-
 		"zdo bind 0x${device.deviceNetworkId} ${endpointId} 1 1 {${device.zigbeeId}} {}", "delay 200",
 		"zcl global send-me-a-report 1 0x20 0x20 30 21600 {01}",		//checkin time 6 hrs
 		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
@@ -270,7 +266,7 @@ def configure() {
 		"zcl global send-me-a-report 0x402 0 0x29 30 3600 {6400}",
 		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500"
 	]
-    return configCmds + refresh() // send refresh cmds as part of config
+    return refresh() + configCmds  // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-multi-sensor.src/README.md

@@ -26,10 +26,10 @@ Works with:
 
 ## Device Health
 
-A Category C2 multi sensor with maxReportTime of 1 hr.
-Check-in interval is double the value of maxReportTime for Zigbee device. 
+A Category C2 multi sensor with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime. 
 This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 2*60 = 120 min
+Check-in interval = 12 mins
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-multi-sensor.src/smartsense-multi-sensor.groovy

@@ -16,7 +16,7 @@
 import physicalgraph.zigbee.clusters.iaszone.ZoneStatus
 
 metadata {
-	definition (name: "SmartSense Multi Sensor", namespace: "smartthings", author: "SmartThings", category: "C2") {
+	definition (name: "SmartSense Multi Sensor", namespace: "smartthings", author: "SmartThings") {
 
 		capability "Three Axis"
 		capability "Battery"
@@ -115,6 +115,34 @@ metadata {
 	}
  }
 
+def installed() {
+	log.debug "${device} installed"
+}
+
+def updated() {
+	log.debug "updated called"
+	log.info "garage value : $garageSensor"
+	if (garageSensor == "Yes") {
+		def descriptionText = "Updating device to garage sensor"
+		if (device.latestValue("status") == "open") {
+			sendEvent(name: 'status', value: 'garage-open', descriptionText: descriptionText, translatable: true)
+		}
+		else if (device.latestValue("status") == "closed") {
+			sendEvent(name: 'status', value: 'garage-closed', descriptionText: descriptionText, translatable: true)
+		}
+	}
+	else {
+		def descriptionText = "Updating device to open/close sensor"
+		if (device.latestValue("status") == "garage-open") {
+			sendEvent(name: 'status', value: 'open', descriptionText: descriptionText, translatable: true)
+		}
+		else if (device.latestValue("status") == "garage-closed") {
+			sendEvent(name: 'status', value: 'closed', descriptionText: descriptionText, translatable: true)
+		}
+	}
+	configureHealthCheck()
+}
+
 def parse(String description) {
 	Map map = [:]
 	if (description?.startsWith('catchall:')) {
@@ -147,20 +175,33 @@ private Map parseCatchAllMessage(String description) {
 	if (shouldProcessMessage(cluster)) {
 		switch(cluster.clusterId) {
 			case 0x0001:
-			resultMap = getBatteryResult(cluster.data.last())
+				// 0x07 - configure reporting
+				if (cluster.command != 0x07) {
+					resultMap = getBatteryResult(cluster.data.last())
+				}
 			break
 
 			case 0xFC02:
-			log.debug 'ACCELERATION'
+				log.debug 'ACCELERATION'
 			break
 
 			case 0x0402:
-			log.debug 'TEMP'
-				// temp is last 2 data values. reverse to swap endian
-				String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
-				def value = getTemperature(temp)
-				resultMap = getTemperatureResult(value)
-				break
+				if (cluster.command == 0x07) {
+					if(cluster.data[0] == 0x00) {
+						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
+						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+					}
+					else {
+						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+					}
+				}
+				else {
+					// temp is last 2 data values. reverse to swap endian
+					String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
+					def value = getTemperature(temp)
+					resultMap = getTemperatureResult(value)
+				}
+			break
 		}
 	}
 
@@ -169,10 +210,8 @@ private Map parseCatchAllMessage(String description) {
 
 private boolean shouldProcessMessage(cluster) {
 	// 0x0B is default response indicating message got through
-	// 0x07 is bind message
 	boolean ignoredMessage = cluster.profileId != 0x0104 ||
 	cluster.command == 0x0B ||
-	cluster.command == 0x07 ||
 	(cluster.data.size() > 0 && cluster.data.first() == 0x3e)
 	return !ignoredMessage
 }
@@ -235,35 +274,12 @@ private Map parseIasMessage(String description) {
 	return resultMap
 }
 
-def updated() {
-	log.debug "updated called"
-	log.info "garage value : $garageSensor"
-	if (garageSensor == "Yes") {
-		def descriptionText = "Updating device to garage sensor"
-		if (device.latestValue("status") == "open") {
-			sendEvent(name: 'status', value: 'garage-open', descriptionText: descriptionText, translatable: true)
-		}
-		else if (device.latestValue("status") == "closed") {
-			sendEvent(name: 'status', value: 'garage-closed', descriptionText: descriptionText, translatable: true)
-		}
-	}
-	else {
-		def descriptionText = "Updating device to open/close sensor"
-		if (device.latestValue("status") == "garage-open") {
-			sendEvent(name: 'status', value: 'open', descriptionText: descriptionText, translatable: true)
-		}
-		else if (device.latestValue("status") == "garage-closed") {
-			sendEvent(name: 'status', value: 'closed', descriptionText: descriptionText, translatable: true)
-		}
-	}
-}
-
 def getTemperature(value) {
 	def celsius = Integer.parseInt(value, 16).shortValue() / 100
 	if(getTemperatureScale() == "C"){
-		return celsius
+		return Math.round(celsius)
 		} else {
-			return celsiusToFahrenheit(celsius) as Integer
+			return Math.round(celsiusToFahrenheit(celsius))
 		}
 	}
 
@@ -400,23 +416,25 @@ def refresh() {
 	return refreshCmds + enrollResponse()
 }
 
-def configure() {
-	// Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-	sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
+def configureHealthCheck(){
+	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// enrolls with default periodic reporting until newer 5 min interval is confirmed
+	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+}
 
+def configure() {
 	log.debug "Configuring Reporting"
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	def configCmds = enrollResponse() +
-			zigbee.batteryConfig() +
+	def configCmds = zigbee.batteryConfig() +
 			zigbee.temperatureConfig(30, 300) +
 			zigbee.configureReporting(0xFC02, 0x0010, 0x18, 10, 3600, 0x01, [mfgCode: manufacturerCode]) +
 			zigbee.configureReporting(0xFC02, 0x0012, 0x29, 1, 3600, 0x0001, [mfgCode: manufacturerCode]) +
 			zigbee.configureReporting(0xFC02, 0x0013, 0x29, 1, 3600, 0x0001, [mfgCode: manufacturerCode]) +
 			zigbee.configureReporting(0xFC02, 0x0014, 0x29, 1, 3600, 0x0001, [mfgCode: manufacturerCode])
 
-	return configCmds + refresh()
+	return refresh() + configCmds
 }
 
 private getEndpointId() {

devicetypes/smartthings/smartsense-open-closed-accelerometer-sensor.src/smartsense-open-closed-accelerometer-sensor.groovy

@@ -277,12 +277,8 @@ def getTemperature(value) {
 def configure() {
 	sendEvent(name: "checkInterval", value: 7200, displayed: false)
 
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
 	log.debug "Configuring Reporting, IAS CIE, and Bindings."
 	def configCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
-
 		"zdo bind 0x${device.deviceNetworkId} ${endpointId} 1 1 {${device.zigbeeId}} {}", "delay 200",
 		"zcl global send-me-a-report 1 0x20 0x20 30 21600 {01}",		//checkin time 6 hrs
 		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500",
@@ -295,7 +291,7 @@ def configure() {
 		"zcl global send-me-a-report 0xFC02 2 0x18 30 3600 {01}",
 		"send 0x${device.deviceNetworkId} 1 ${endpointId}", "delay 500"
 	]
-	return configCmds + refresh() // send refresh cmds as part of config
+	return refresh() + configCmds // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-open-closed-sensor.src/README.md

@@ -24,10 +24,10 @@ Works with:
 
 ## Device Health
 
-A Category C2 open/closed sensor with maxReportTime of 1 hr.
-Check-in interval is double the value of maxReportTime for Zigbee device. 
+A Category C2 open/closed sensor with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime. 
 This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 2*60 = 120 min
+Check-in interval = 12 mins
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-open-closed-sensor.src/smartsense-open-closed-sensor.groovy

@@ -16,7 +16,7 @@
 import physicalgraph.zigbee.clusters.iaszone.ZoneStatus
 
 metadata {
-	definition (name: "SmartSense Open/Closed Sensor", namespace: "smartthings", author: "SmartThings", category: "C2") {
+	definition (name: "SmartSense Open/Closed Sensor", namespace: "smartthings", author: "SmartThings") {
 		capability "Battery"
 		capability "Configuration"
 		capability "Contact Sensor"
@@ -75,6 +75,15 @@ metadata {
 	}
 }
 
+def installed() {
+	log.debug "${device} installed"
+}
+
+def updated() {
+	log.debug "${device} updated"
+	configureHealthCheck()
+}
+
 def parse(String description) {
 	log.debug "description: $description"
 
@@ -109,15 +118,28 @@ private Map parseCatchAllMessage(String description) {
     if (shouldProcessMessage(cluster)) {
         switch(cluster.clusterId) {
             case 0x0001:
-            	resultMap = getBatteryResult(cluster.data.last())
+				// 0x07 - configure reporting
+				if (cluster.command != 0x07) {
+					resultMap = getBatteryResult(cluster.data.last())
+				}
                 break
 
             case 0x0402:
-                log.debug 'TEMP'
-                // temp is last 2 data values. reverse to swap endian
-                String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
-                def value = getTemperature(temp)
-                resultMap = getTemperatureResult(value)
+				if (cluster.command == 0x07){
+					if (cluster.data[0] == 0x00) {
+						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
+						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+					}
+					else {
+						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+					}
+				}
+				else {
+					// temp is last 2 data values. reverse to swap endian
+					String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
+					def value = getTemperature(temp)
+					resultMap = getTemperatureResult(value)
+				}
                 break
         }
     }
@@ -127,10 +149,8 @@ private Map parseCatchAllMessage(String description) {
 
 private boolean shouldProcessMessage(cluster) {
     // 0x0B is default response indicating message got through
-    // 0x07 is bind message
     boolean ignoredMessage = cluster.profileId != 0x0104 ||
         cluster.command == 0x0B ||
-        cluster.command == 0x07 ||
         (cluster.data.size() > 0 && cluster.data.first() == 0x3e)
     return !ignoredMessage
 }
@@ -254,20 +274,17 @@ def refresh() {
 	return refreshCmds + enrollResponse()
 }
 
+def configureHealthCheck() {
+	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// enrolls with default periodic reporting until newer 5 min interval is confirmed
+	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+}
 def configure() {
-	// Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-	sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
-
-	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
 	log.debug "Configuring Reporting, IAS CIE, and Bindings."
-	def enrollCmds = [
-		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
-		"send 0x${device.deviceNetworkId} 1 1", "delay 500",
-	]
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-    return enrollCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) + refresh() // send refresh cmds as part of config
+    return refresh() + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/README.md

@@ -24,10 +24,10 @@ Works with:
 
 ## Device Health
 
-A Category C2 SmartSense Temp/Humidity Sensor with maxReportTime of 1 hr.
-Check-in interval is double the value of maxReportTime for Zigbee device. 
+A Category C2 SmartSense Temp/Humidity Sensor with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime. 
 This gives the device twice the amount of time to respond before it is marked as offline.
-Check-in interval = 2*60 = 120 min
+Check-in interval = 12 mins
 
 ## Battery Specification
 

devicetypes/smartthings/smartsense-temp-humidity-sensor.src/smartsense-temp-humidity-sensor.groovy

@@ -14,7 +14,7 @@
  *
  */
 metadata {
-	definition (name: "SmartSense Temp/Humidity Sensor",namespace: "smartthings", author: "SmartThings", category: "C2") {
+	definition (name: "SmartSense Temp/Humidity Sensor",namespace: "smartthings", author: "SmartThings") {
 		capability "Configuration"
 		capability "Battery"
 		capability "Refresh"
@@ -69,6 +69,15 @@ metadata {
 	}
 }
 
+def installed() {
+	log.debug "${device} installed"
+}
+
+def updated() {
+	log.debug "${device} updated"
+	configureHealthCheck()
+}
+
 def parse(String description) {
 	log.debug "description: $description"
 
@@ -93,20 +102,37 @@ private Map parseCatchAllMessage(String description) {
     if (shouldProcessMessage(cluster)) {
         switch(cluster.clusterId) {
             case 0x0001:
-            	resultMap = getBatteryResult(cluster.data.last())
+				// 0x07 - configure reporting
+				if (cluster.command != 0x07) {
+					resultMap = getBatteryResult(cluster.data.last())
+				}
                 break
 
             case 0x0402:
-                // temp is last 2 data values. reverse to swap endian
-                String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
-                def value = getTemperature(temp)
-                resultMap = getTemperatureResult(value)
-                break
+				if (cluster.command == 0x07) {
+					if (cluster.data[0] == 0x00){
+						log.debug "TEMP REPORTING CONFIG RESPONSE" + cluster
+						sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+					}
+					else {
+						log.warn "TEMP REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+					}
+				}
+				else {
+					// temp is last 2 data values. reverse to swap endian
+					String temp = cluster.data[-2..-1].reverse().collect { cluster.hex1(it) }.join()
+					def value = getTemperature(temp)
+					resultMap = getTemperatureResult(value)
+				}
+				break
 
 			case 0xFC45:
-                String pctStr = cluster.data[-1, -2].collect { Integer.toHexString(it) }.join('')
-                String display = Math.round(Integer.valueOf(pctStr, 16) / 100)
-                resultMap = getHumidityResult(display)
+				// 0x07 - configure reporting
+				if (cluster.command != 0x07) {
+					String pctStr = cluster.data[-1, -2].collect { Integer.toHexString(it) }.join('')
+					String display = Math.round(Integer.valueOf(pctStr, 16) / 100)
+					resultMap = getHumidityResult(display)
+				}
                 break
         }
     }
@@ -116,10 +142,8 @@ private Map parseCatchAllMessage(String description) {
 
 private boolean shouldProcessMessage(cluster) {
     // 0x0B is default response indicating message got through
-    // 0x07 is bind message
     boolean ignoredMessage = cluster.profileId != 0x0104 ||
         cluster.command == 0x0B ||
-        cluster.command == 0x07 ||
         (cluster.data.size() > 0 && cluster.data.first() == 0x3e)
     return !ignoredMessage
 }
@@ -235,11 +259,7 @@ private Map getTemperatureResult(value) {
 
 private Map getHumidityResult(value) {
 	log.debug 'Humidity'
-	return [
-		name: 'humidity',
-		value: value,
-		unit: '%'
-	]
+	return value ? [name: 'humidity', value: value, unit: '%'] : [:]
 }
 
 /**
@@ -252,21 +272,18 @@ def ping() {
 def refresh()
 {
 	log.debug "refresh temperature, humidity, and battery"
-	[
+	return zigbee.readAttribute(0xFC45, 0x0000, ["mfgCode": 0xC2DF]) +   // Original firmware
+			zigbee.readAttribute(0x0402, 0x0000) +
+			zigbee.readAttribute(0x0001, 0x0020)
+}
 
-		"zcl mfg-code 0xC2DF", "delay 1000",
-		"zcl global read 0xFC45 0", "delay 1000",
-		"send 0x${device.deviceNetworkId} 1 1", "delay 1000",
-        "st rattr 0x${device.deviceNetworkId} 1 0x402 0", "delay 200",
-        "st rattr 0x${device.deviceNetworkId} 1 1 0x20"
-
-	]
+def configureHealthCheck() {
+	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// enrolls with default periodic reporting until newer 5 min interval is confirmed
+	sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 }
 
 def configure() {
-	// Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-	sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
-
 	log.debug "Configuring Reporting and Bindings."
 	def humidityConfigCmds = [
 		"zdo bind 0x${device.deviceNetworkId} 1 1 0xFC45 {${device.zigbeeId}} {}", "delay 500",
@@ -276,7 +293,7 @@ def configure() {
 
 	// temperature minReportTime 30 seconds, maxReportTime 5 min. Reporting interval if no activity
 	// battery minReport 30 seconds, maxReportTime 6 hrs by default
-	return humidityConfigCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) +  refresh() // send refresh cmds as part of config
+	return refresh() + humidityConfigCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300)  // send refresh cmds as part of config
 }
 
 private hex(value) {

devicetypes/smartthings/tyco-door-window-sensor.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/tyco-door-window-sensor.src/README.md

@@ -0,0 +1,42 @@
+# Tyco Door Window Sensor
+
+
+
+Works with: 
+
+* [Tyco Door Window Sensor](https://support.smartthings.com/hc/en-us/articles/204834100-Tyco-Door-Window-Sensor)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+
+## Capabilities
+
+* **Battery** - defines device uses a battery
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Contact Sensor** - can detect contact (open/close)
+* **Refresh** - _refresh()_ command for status updates
+* **Temperature Measurement** - can measure the device temperature
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Contact sensor with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime for Zigbee device. 
+This gives the device twice the amount of time to respond before it is marked as offline.
+Check-in interval = 12 min
+
+## Battery Specification
+
+3V CR2032 battery is required.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that either the sensor needs to be reseted or the sensor is out of range.
+Reset needs to be done by inserting the battery in the sensor and then quickly pressing the adjacent black button 10 times. Pairing should be tried again now.
+It may happen that sensor is out of range, then pairing needs to be tried again by placing the sensor closer to the hub.
+Instructions related to pairing, resetting and removing the different motion sensors from SmartThings can be found in the following links
+for the different models:
+* [Tyco Door Window Sensor (MCT-340)](https://support.smartthings.com/hc/en-us/articles/204834100-Tyco-Door-Window-Sensor)

devicetypes/smartthings/tyco-door-window-sensor.src/tyco-door-window-sensor.groovy

@@ -22,6 +22,7 @@ metadata {
 		capability "Contact Sensor"
 		capability "Refresh"
 		capability "Temperature Measurement"
+		capability "Health Check"
 
 		command "enrollResponse"
 
@@ -229,44 +230,42 @@ private Map getContactResult(value) {
 	]
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	return zigbee.readAttribute(0x0402, 0x0000) // Read the Temperature Cluster
+}
+
 def refresh()
 {
 	log.debug "Refreshing Temperature and Battery"
-	[
+	def refreshCmds = [
 
         "st rattr 0x${device.deviceNetworkId} 1 0x402 0", "delay 200",
 		"st rattr 0x${device.deviceNetworkId} 1 1 0x20"
 
 	]
+
+	return refreshCmds + enrollResponse()
 }
 
 def configure() {
+	// Device-Watch allows 2 check-in misses from device
+	sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 
 	String zigbeeEui = swapEndianHex(device.hub.zigbeeEui)
 		log.debug "Configuring Reporting, IAS CIE, and Bindings."
-	def configCmds = [
+	def enrollCmds = [
     	"delay 1000",
 
 		"zcl global write 0x500 0x10 0xf0 {${zigbeeEui}}", "delay 200",
 		"send 0x${device.deviceNetworkId} 1 1", "delay 1500",
 
-        "zcl global send-me-a-report 1 0x20 0x20 600 3600 {01}", "delay 200",
-        "send 0x${device.deviceNetworkId} 1 1", "delay 1500",
-
-        "zcl global send-me-a-report 0x402 0 0x29 300 3600 {6400}", "delay 200",
-        "send 0x${device.deviceNetworkId} 1 1", "delay 1500",
-
-
         //"raw 0x500 {01 23 00 00 00}", "delay 200",
         //"send 0x${device.deviceNetworkId} 1 1", "delay 1500",
-
-
-		"zdo bind 0x${device.deviceNetworkId} 1 1 0x402 {${device.zigbeeId}} {}", "delay 500",
-		"zdo bind 0x${device.deviceNetworkId} 1 1 1 {${device.zigbeeId}} {}",
-
-        "delay 500"
 	]
-    return configCmds + enrollResponse() + refresh() // send refresh cmds as part of config
+    return enrollCmds + zigbee.batteryConfig() + zigbee.temperatureConfig(30, 300) + refresh() // send refresh cmds as part of config
 }
 
 def enrollResponse() {

devicetypes/smartthings/zigbee-button.src/zigbee-button.groovy

@@ -89,14 +89,8 @@ def parse(String description) {
 }
 
 private Map parseIasButtonMessage(String description) {
-    int zoneInt = Integer.parseInt((description - "zone status 0x"), 16)
-    if (zoneInt & 0x02) {
-        resultMap = getButtonResult('press')
-    } else {
-        resultMap = getButtonResult('release')
-    }
-
-    return resultMap
+    def zs = zigbee.parseZoneStatus(description)
+    return zs.isAlarm2Set() ? getButtonResult("press") : getButtonResult("release")
 }
 
 private Map getBatteryResult(rawValue) {

devicetypes/smartthings/zigbee-dimmer-power.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zigbee-dimmer-power.src/README.md

@@ -0,0 +1,41 @@
+# GE Plug-In/In-Wall Smart Dimmer (ZigBee)
+
+
+
+Works with:
+
+* [GE In-Wall Smart Dimmer (ZigBee)](https://shop.smartthings.com/#!/products/ge-in-wall-smart-dimmer-switch)
+* [GE Plug-In Smart Dimmer (ZigBee)](https://www.smartthings.com/works-with-smartthings/ge/ge-plug-in-smart-dimmer-zigbee)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#Troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Refresh** - _refresh()_ command for status updates
+* **Power Meter** - ability to check the power meter(energy consumption) of device
+* **Sensor** - represents the device sensor capability
+* **Switch** - can detect state (possible values: on/off)
+* **Switch Level** - represents current light level, usually 0-100 in percent
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+A Zigbee dimmer with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime.
+This gives the device twice the amount of time to respond before it is marked as offline.
+Enrolls with default periodic reporting until newer 5 min interval is confirmed
+It then enrolls the device with updated checkInterval i.e. 12 mins
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [GE Z-Wave In-Wall Smart Dimmer (GE 45857) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/204988564-GE-In-Wall-Smart-Dimmer-45857GE-ZigBee-)
+* [GE Zigbee Plug-in Smart Dimmer (GE 45852) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/205239280-GE-Plug-In-Smart-Dimmer-45852GE-ZigBee-)

devicetypes/smartthings/zigbee-dimmer-power.src/zigbee-dimmer-power.groovy

@@ -21,6 +21,7 @@ metadata {
         capability "Sensor"
         capability "Switch"
         capability "Switch Level"
+        capability "Health Check"
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0B04"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 0702"
@@ -70,8 +71,20 @@ def parse(String description) {
         }
     }
     else {
-        log.warn "DID NOT PARSE MESSAGE for description : $description"
-        log.debug zigbee.parseDescriptionAsMap(description)
+        def cluster = zigbee.parse(description)
+        if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
+            if (cluster.data[0] == 0x00){
+                log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
+                sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+            }
+            else {
+                log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+            }
+        }
+        else {
+            log.warn "DID NOT PARSE MESSAGE for description : $description"
+            log.debug zigbee.parseDescriptionAsMap(description)
+        }
     }
 }
 
@@ -87,11 +100,22 @@ def setLevel(value) {
     zigbee.setLevel(value)
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+    return zigbee.onOffRefresh()
+}
+
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
 }
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh()
+
+    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+    // enrolls with default periodic reporting until newer 5 min interval is confirmed
+    sendEvent(name: "checkInterval", value: 3 * 60 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+    refresh()
 }

devicetypes/smartthings/zigbee-dimmer.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zigbee-dimmer.src/README.md

@@ -0,0 +1,36 @@
+# OSRAM Lightify LED On/Off/Dim
+
+
+
+Works with: 
+
+* [OSRAM Lightify LED On/Off/Dim](https://shop.smartthings.com/#!/products/osram-led-smart-bulb-on-off-dim)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Refresh** - _refresh()_ command for status updates
+* **Switch** - can detect state (possible values: on/off)
+* **Switch Level** - represents current light level, usually 0-100 in percent
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+A Category C1 Zigbee dimmer with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime. 
+This gives the device twice the amount of time to respond before it is marked as offline.
+Check-in interval = 12 mins
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Other troubleshooting tips are listed as follows:
+* [Troubleshooting:](https://support.smartthings.com/hc/en-us/articles/207191763-OSRAM-LIGHTIFY-LED-Smart-Connected-Light-A19-On-Off-Dim)

devicetypes/smartthings/zigbee-dimmer.src/zigbee-dimmer.groovy

@@ -48,6 +48,15 @@ metadata {
     }
 }
 
+def installed() {
+    log.debug "${device} installed"
+}
+
+def updated() {
+    log.debug "${device} updated"
+    configureHealthCheck()
+}
+
 // Parse incoming device messages to generate events
 def parse(String description) {
     log.debug "description is $description"
@@ -60,8 +69,21 @@ def parse(String description) {
         }
     }
     else {
-        log.warn "DID NOT PARSE MESSAGE for description : $description"
-        log.debug zigbee.parseDescriptionAsMap(description)
+        def cluster = zigbee.parse(description)
+
+        if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
+            if (cluster.data[0] == 0x00) {
+                log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
+                sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+            }
+            else {
+                log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+            }
+        }
+        else {
+            log.warn "DID NOT PARSE MESSAGE for description : $description"
+            log.debug "${cluster}"
+        }
     }
 }
 
@@ -84,13 +106,16 @@ def ping() {
 }
 
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig() + zigbee.levelConfig()
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig()
+}
+
+def configureHealthCheck() {
+    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+    // enrolls with default periodic reporting until newer 5 min interval is confirmed
+    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 }
 
 def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-    sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
     // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig()
 }

devicetypes/smartthings/zigbee-lock.src/zigbee-lock.groovy

@@ -31,7 +31,8 @@
         fingerprint profileId: "0104", inClusters: "0000,0001,0003,0009,000A,0101,0020", outClusters: "000A,0019", manufacturer: "Yale", model: "YRD210 PB DB", deviceJoinName: "Yale Push Button Deadbolt Lock"
         fingerprint profileId: "0104", inClusters: "0000,0001,0003,0009,000A,0101,0020", outClusters: "000A,0019", manufacturer: "Yale", model: "YRD220/240 TSDB", deviceJoinName: "Yale Touch Screen Deadbolt Lock"
         fingerprint profileId: "0104", inClusters: "0000,0001,0003,0009,000A,0101,0020", outClusters: "000A,0019", manufacturer: "Yale", model: "YRL210 PB LL", deviceJoinName: "Yale Push Button Lever Lock"
-    }
+	fingerprint profileId: "0104", inClusters: "0000,0001,0003,0009,000A,0101,0020", outClusters: "000A,0019", manufacturer: "Yale", model: "YRD226/246 TSDB", deviceJoinName: "Yale Touch Screen Deadbolt Lock"
+	}
 
     tiles(scale: 2) {
 		multiAttributeTile(name:"toggle", type:"generic", width:6, height:4){
@@ -89,7 +90,7 @@ def configure() {
         zigbee.configureReporting(CLUSTER_POWER, POWER_ATTR_BATTERY_PERCENTAGE_REMAINING,
                                   TYPE_U8, 600, 21600, 0x01)
     log.info "configure() --- cmds: $cmds"
-    return cmds + refresh() // send refresh cmds as part of config
+    return refresh() + cmds // send refresh cmds as part of config
 }
 
 def refresh() {

devicetypes/smartthings/zigbee-rgb-bulb.src/zigbee-rgb-bulb.groovy

@@ -0,0 +1,154 @@
+/**
+ *  Copyright 2016 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ *  Author: SmartThings
+ *  Date: 2016-01-19
+ *
+ *  This DTH should serve as the generic DTH to handle RGB ZigBee HA devices (For color bulbs with no color temperature)
+ */
+
+metadata {
+	definition (name: "ZigBee RGB Bulb", namespace: "smartthings", author: "SmartThings") {
+
+		capability "Actuator"
+		capability "Color Control"
+		capability "Configuration"
+		capability "Polling"
+		capability "Refresh"
+		capability "Switch"
+		capability "Switch Level"
+		capability "Health Check"
+
+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "Gardenspot RGB", deviceJoinName: "OSRAM LIGHTIFY Gardenspot mini RGB"
+		fingerprint profileId: "0104", inClusters: "0000,0003,0004,0005,0006,0008,0300,0B04,FC0F", outClusters: "0019", manufacturer: "OSRAM", model: "LIGHTIFY Gardenspot RGB", deviceJoinName: "OSRAM LIGHTIFY Gardenspot mini RGB"
+	}
+
+	// UI tile definitions
+	tiles(scale: 2) {
+		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
+			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
+				attributeState "on", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
+				attributeState "off", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
+				attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
+				attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
+			}
+			tileAttribute ("device.level", key: "SLIDER_CONTROL") {
+				attributeState "level", action:"switch level.setLevel"
+			}
+			tileAttribute ("device.color", key: "COLOR_CONTROL") {
+				attributeState "color", action:"color control.setColor"
+			}
+		}
+		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
+			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
+		}
+
+		main(["switch"])
+		details(["switch", "refresh"])
+	}
+}
+
+//Globals
+private getATTRIBUTE_HUE() { 0x0000 }
+private getATTRIBUTE_SATURATION() { 0x0001 }
+private getHUE_COMMAND() { 0x00 }
+private getSATURATION_COMMAND() { 0x03 }
+private getCOLOR_CONTROL_CLUSTER() { 0x0300 }
+
+// Parse incoming device messages to generate events
+def parse(String description) {
+	log.debug "description is $description"
+
+	def event = zigbee.getEvent(description)
+	if (event) {
+		log.debug event
+		if (event.name=="level" && event.value==0) {}
+		else {
+			sendEvent(event)
+		}
+	}
+	else {
+		def zigbeeMap = zigbee.parseDescriptionAsMap(description)
+		def cluster = zigbee.parse(description)
+
+		if (zigbeeMap?.clusterInt == COLOR_CONTROL_CLUSTER) {
+			if(zigbeeMap.attrInt == ATTRIBUTE_HUE){  //Hue Attribute
+				def hueValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
+				sendEvent(name: "hue", value: hueValue, descriptionText: "Color has changed")
+			}
+			else if(zigbeeMap.attrInt == ATTRIBUTE_SATURATION){ //Saturation Attribute
+				def saturationValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
+				sendEvent(name: "saturation", value: saturationValue, descriptionText: "Color has changed", displayed: false)
+			}
+		}
+		else if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
+			if (cluster.data[0] == 0x00){
+				log.debug "ON/OFF REPORTING CONFIG RESPONSE: $cluster"
+				sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+			}
+			else {
+				log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+			}
+		}
+		else {
+			log.info "DID NOT PARSE MESSAGE for description : $description"
+			log.debug zigbeeMap
+		}
+	}
+}
+
+def on() {
+	zigbee.on()
+}
+
+def off() {
+	zigbee.off()
+}
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	return zigbee.onOffRefresh()
+}
+
+def refresh() {
+	zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION) + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
+}
+
+def configure() {
+	log.debug "Configuring Reporting and Bindings."
+	// Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+	// enrolls with default periodic reporting until newer 5 min interval is confirmed
+	sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+
+	// OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
+	zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01) + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
+}
+
+def setLevel(value) {
+	zigbee.setLevel(value)
+}
+
+def setColor(value){
+	log.trace "setColor($value)"
+	zigbee.on() + setHue(value.hue) + "delay 500" + setSaturation(value.saturation)
+}
+
+def setHue(value) {
+	def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
+	zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500")       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
+}
+
+def setSaturation(value) {
+	def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
+	zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + "delay 1000" + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
+}

devicetypes/smartthings/zigbee-rgbw-bulb.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zigbee-rgbw-bulb.src/README.md

@@ -0,0 +1,42 @@
+# OSRAM LIGHTIFY LED RGBW Bulb
+
+
+
+Works with: 
+
+* [OSRAM LIGHTIFY LED RGBW Bulb](https://support.smartthings.com/hc/en-us/articles/207728173-OSRAM-LIGHTIFY-LED-Smart-Connected-Light-A19-RGBW)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+
+## Capabilities
+
+* **Actuator** - It represents that a device has commands.
+* **Color Control** - It represents that the color attributes of a device can be controlled (hue, saturation, color value).
+* **Color Temperature** - It represents color temperature capability measured in degree Kelvin.
+* **Polling** - It represents that a device can be polled.
+* **Switch** - can detect state (possible values: on/off)
+* **Switch Level** - can detect current light level (0-100 in percent)
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated
+* **Refresh** - _refresh()_ command for status updates
+* **Health Check** - indicates ability to get device health notifications
+
+
+## Device Health
+
+A Category C6 OSRAM LIGHTIFY LED RGBW Bulb with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime. 
+This gives the device twice the amount of time to respond before it is marked as offline.
+Check-in interval = 12 mins
+
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+It may also happen that you need to reset the device.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/207728173-OSRAM-LIGHTIFY-LED-Smart-Connected-Light-A19-RGBW)

devicetypes/smartthings/zigbee-rgbw-bulb.src/zigbee-rgbw-bulb.groovy

@@ -70,6 +70,16 @@ metadata {
     }
 }
 
+
+def installed() {
+    log.debug "${device} installed"
+}
+
+def updated() {
+    log.debug "${device} updated"
+    configureHealthCheck()
+}
+
 //Globals
 private getATTRIBUTE_HUE() { 0x0000 }
 private getATTRIBUTE_SATURATION() { 0x0001 }
@@ -95,7 +105,7 @@ def parse(String description) {
     }
     else {
         def zigbeeMap = zigbee.parseDescriptionAsMap(description)
-        log.trace "zigbeeMap : $zigbeeMap"
+        def cluster = zigbee.parse(description)
 
         if (zigbeeMap?.clusterInt == COLOR_CONTROL_CLUSTER) {
             if(zigbeeMap.attrInt == ATTRIBUTE_HUE){  //Hue Attribute
@@ -107,8 +117,18 @@ def parse(String description) {
                 sendEvent(name: "saturation", value: saturationValue, descriptionText: "Color has changed", displayed: false)
             }
         }
+        else if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
+            if (cluster.data[0] == 0x00){
+                log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
+                sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+            }
+            else {
+                log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+            }
+        }
         else {
             log.info "DID NOT PARSE MESSAGE for description : $description"
+            log.debug zigbeeMap
         }
     }
 }
@@ -128,15 +148,18 @@ def ping() {
 }
 
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.readAttribute(0x0008, 0x00) + zigbee.readAttribute(0x0300, 0x00) + zigbee.readAttribute(0x0300, ATTRIBUTE_COLOR_TEMPERATURE) + zigbee.readAttribute(0x0300, ATTRIBUTE_HUE) + zigbee.readAttribute(0x0300, ATTRIBUTE_SATURATION) + zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
+    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_COLOR_TEMPERATURE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION) + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
+}
+
+def configureHealthCheck() {
+    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+    // enrolls with default periodic reporting until newer 5 min interval is confirmed
+    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 }
 
 def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-    sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
-    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01) + zigbee.readAttribute(0x0006, 0x00) + zigbee.readAttribute(0x0008, 0x00) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, 0x00) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_COLOR_TEMPERATURE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
+    refresh()
 }
 
 def setColorTemperature(value) {
@@ -177,5 +200,5 @@ def setHue(value) {
 
 def setSaturation(value) {
     def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500")      //payload-> sat value, transition time
+    zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + "delay 1000" + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
 }

devicetypes/smartthings/zigbee-switch-power.src/zigbee-switch-power.groovy

@@ -20,6 +20,7 @@ metadata {
         capability "Power Meter"
         capability "Sensor"
         capability "Switch"
+        capability "Health Check"
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0B04"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006, 0702"
@@ -77,10 +78,26 @@ def on() {
 }
 
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
+    Integer reportIntervalMinutes = 5
+    zigbee.onOffRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh() + zigbee.onOffConfig(0,reportIntervalMinutes * 60) + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig()
 }
 
 def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.simpleMeteringPowerConfig() + zigbee.electricMeasurementPowerConfig() + zigbee.onOffRefresh() + zigbee.simpleMeteringPowerRefresh() + zigbee.electricMeasurementPowerRefresh()
+    log.debug "in configure()"
+    configureHealthCheck()
+}
+
+def configureHealthCheck() {
+    Integer hcIntervalMinutes = 12
+    refresh()
+    sendEvent(name: "checkInterval", value: hcIntervalMinutes * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+}
+
+def updated() {
+    log.debug "in updated()"
+    configureHealthCheck()
+}
+
+def ping() {
+    return zigbee.onOffRefresh()
 }

devicetypes/smartthings/zigbee-switch.src/zigbee-switch.groovy

@@ -21,6 +21,7 @@ metadata {
 
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0004, 0005, 0006"
         fingerprint profileId: "0104", inClusters: "0000, 0003, 0006", outClusters: "0003, 0006, 0019, 0406", manufacturer: "Leviton", model: "ZSS-10", deviceJoinName: "Leviton Switch"
+        fingerprint profileId: "0104", inClusters: "0000, 0003, 0006", outClusters: "000A", manufacturer: "HAI", model: "65A21-1", deviceJoinName: "Leviton Wireless Load Control Module-30amp"
     }
 
     // simulator metadata
@@ -78,5 +79,5 @@ def refresh() {
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.onOffRefresh()
+    zigbee.onOffRefresh() + zigbee.onOffConfig()
 }

devicetypes/smartthings/zigbee-valve.src/zigbee-valve.groovy

@@ -134,10 +134,5 @@ def refresh() {
 
 def configure() {
     log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() +
-    zigbee.configureReporting(CLUSTER_POWER, POWER_ATTR_BATTERY_PERCENTAGE_REMAINING, TYPE_U8, 600, 21600, 1) +
-    zigbee.configureReporting(CLUSTER_BASIC, BASIC_ATTR_POWER_SOURCE, TYPE_ENUM8, 5, 21600, 1) +
-    zigbee.onOffRefresh() +
-    zigbee.readAttribute(CLUSTER_BASIC, BASIC_ATTR_POWER_SOURCE) +
-    zigbee.readAttribute(CLUSTER_POWER, POWER_ATTR_BATTERY_PERCENTAGE_REMAINING)
+    refresh()
 }

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/README.md

@@ -0,0 +1,37 @@
+# OSRAM Lightify Tunable 60 White
+
+
+
+Works with: 
+
+* [OSRAM Lightify Tunable 60 White](http://www.osram.com/osram_com/tools-and-services/tools/lightify---smart-connected-light/lightify-for-home---what-is-light-to-you/lightify-products/lightify-classic-a60-tunable-white/index.jsp)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Battery](#battery-specification)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Color Temperature** - represents color temperature, measured in degrees Kelvin.
+* **Configuration** - _configure()_ command called when device is installed or device preferences updated.
+* **Refresh** - _refresh()_ command for status updates
+* **Switch** - can detect state (possible values: on/off)
+* **Switch Level** - represents current light level, usually 0-100 in percent
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+A Category C1 OSRAM Lightify Tunable 60 White with maxReportTime of 5 mins.
+Check-in interval is double the value of maxReportTime. 
+This gives the device twice the amount of time to respond before it is marked as offline.
+Check-in interval = 12 mins
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Other troubleshooting tips are listed as follows:
+* [Troubleshooting:](https://support.smartthings.com/hc/en-us/articles/204576454-OSRAM-LIGHTIFY-Tunable-White-60-Bulb)

devicetypes/smartthings/zigbee-white-color-temperature-bulb.src/zigbee-white-color-temperature-bulb.groovy

@@ -69,6 +69,15 @@ metadata {
     }
 }
 
+def installed() {
+    log.debug "${device} installed"
+}
+
+def updated() {
+    log.debug "${device} updated"
+    configureHealthCheck()
+}
+
 // Parse incoming device messages to generate events
 def parse(String description) {
     log.debug "description is $description"
@@ -83,8 +92,21 @@ def parse(String description) {
         }
     }
     else {
-        log.warn "DID NOT PARSE MESSAGE for description : $description"
-        log.debug zigbee.parseDescriptionAsMap(description)
+        def cluster = zigbee.parse(description)
+
+        if (cluster && cluster.clusterId == 0x0006 && cluster.command == 0x07) {
+            if (cluster.data[0] == 0x00) {
+                log.debug "ON/OFF REPORTING CONFIG RESPONSE: " + cluster
+                sendEvent(name: "checkInterval", value: 60 * 12, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+            }
+            else {
+                log.warn "ON/OFF REPORTING CONFIG FAILED- error code:${cluster.data[0]}"
+            }
+        }
+        else {
+            log.warn "DID NOT PARSE MESSAGE for description : $description"
+            log.debug "${cluster}"
+        }
     }
 }
 
@@ -108,15 +130,18 @@ def ping() {
 }
 
 def refresh() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.colorTemperatureConfig()
+    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig()
+}
+
+def configureHealthCheck() {
+    // Device-Watch allows 3 check-in misses from device (plus 1 min lag time)
+    // enrolls with default periodic reporting until newer 5 min interval is confirmed
+    sendEvent(name: "checkInterval", value: 3 * 10 * 60 + 1 * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
 }
 
 def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    // Device-Watch allows 3 check-in misses from device. 300 seconds x 3 = 15min
-    sendEvent(name: "checkInterval", value: 900, displayed: false, data: [protocol: "zigbee"])
-    // OnOff minReportTime 0 seconds, maxReportTime 5 min. Reporting interval if no activity
-    zigbee.onOffConfig(0, 300) + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
+    refresh()
 }
 
 def setColorTemperature(value) {

devicetypes/smartthings/zll-dimmer-bulb.src/zll-dimmer-bulb.groovy

@@ -11,6 +11,9 @@
  *  for the specific language governing permissions and limitations under the License.
  *
  */
+import groovy.transform.Field
+
+@Field Boolean hasConfiguredHealthCheck = false
 
 metadata {
     definition (name: "ZLL Dimmer Bulb", namespace: "smartthings", author: "SmartThings") {
@@ -21,6 +24,7 @@ metadata {
         capability "Refresh"
         capability "Switch"
         capability "Switch Level"
+        capability "Health Check"
 
         //fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0000,0019"
         fingerprint profileId: "C05E", inClusters: "0000, 0003, 0004, 0005, 0006, 0008, 1000", outClusters: "0019"
@@ -96,7 +100,38 @@ def poll() {
     refresh()
 }
 
-def configure() {
-    log.debug "Configuring Reporting and Bindings."
-    zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+    return zigbee.levelRefresh()
+}
+
+def healthPoll() {
+    log.debug "healthPoll()"
+    def cmds = refresh()
+    cmds.each{ sendHubCommand(new physicalgraph.device.HubAction(it))}
+}
+
+def configureHealthCheck() {
+    Integer hcIntervalMinutes = 12
+    if (!hasConfiguredHealthCheck) {
+        log.debug "Configuring Health Check, Reporting"
+        unschedule("healthPoll")
+        runEvery5Minutes("healthPoll")
+        // Device-Watch allows 2 check-in misses from device
+        sendEvent(name: "checkInterval", value: hcIntervalMinutes * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+        hasConfiguredHealthCheck = true
+    }
+}
+
+def configure() {
+    log.debug "configure()"
+    zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh()
+    configureHealthCheck()
+}
+
+def updated() {
+    log.debug "updated()"
+    configureHealthCheck()
 }

devicetypes/smartthings/zll-rgb-bulb.src/zll-rgb-bulb.groovy

@@ -0,0 +1,134 @@
+/**
+ *  Copyright 2016 SmartThings
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+
+metadata {
+	definition (name: "ZLL RGB Bulb", namespace: "smartthings", author: "SmartThings") {
+
+		capability "Actuator"
+		capability "Color Control"
+		capability "Configuration"
+		capability "Polling"
+		capability "Refresh"
+		capability "Switch"
+		capability "Switch Level"
+	}
+
+	// UI tile definitions
+	tiles(scale: 2) {
+		multiAttributeTile(name:"switch", type: "lighting", width: 6, height: 4, canChangeIcon: true){
+			tileAttribute ("device.switch", key: "PRIMARY_CONTROL") {
+				attributeState "on", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
+				attributeState "off", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
+				attributeState "turningOn", label:'${name}', action:"switch.off", icon:"st.lights.philips.hue-single", backgroundColor:"#79b821", nextState:"turningOff"
+				attributeState "turningOff", label:'${name}', action:"switch.on", icon:"st.lights.philips.hue-single", backgroundColor:"#ffffff", nextState:"turningOn"
+			}
+			tileAttribute ("device.level", key: "SLIDER_CONTROL") {
+				attributeState "level", action:"switch level.setLevel"
+			}
+			tileAttribute ("device.color", key: "COLOR_CONTROL") {
+				attributeState "color", action:"color control.setColor"
+			}
+		}
+		standardTile("refresh", "device.refresh", inactiveLabel: false, decoration: "flat", width: 2, height: 2) {
+			state "default", label:"", action:"refresh.refresh", icon:"st.secondary.refresh"
+		}
+
+		main(["switch"])
+		details(["switch", "refresh"])
+	}
+}
+
+//Globals
+private getATTRIBUTE_HUE() { 0x0000 }
+private getATTRIBUTE_SATURATION() { 0x0001 }
+private getHUE_COMMAND() { 0x00 }
+private getSATURATION_COMMAND() { 0x03 }
+private getCOLOR_CONTROL_CLUSTER() { 0x0300 }
+
+// Parse incoming device messages to generate events
+def parse(String description) {
+	log.debug "description is $description"
+
+	def finalResult = zigbee.getEvent(description)
+	if (finalResult) {
+		log.debug finalResult
+		sendEvent(finalResult)
+	}
+	else {
+		def zigbeeMap = zigbee.parseDescriptionAsMap(description)
+		log.trace "zigbeeMap : $zigbeeMap"
+
+		if (zigbeeMap?.clusterInt == COLOR_CONTROL_CLUSTER) {
+			if(zigbeeMap.attrInt == ATTRIBUTE_HUE){  //Hue Attribute
+				def hueValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 360)
+				sendEvent(name: "hue", value: hueValue, displayed:false)
+			}
+			else if(zigbeeMap.attrInt == ATTRIBUTE_SATURATION){ //Saturation Attribute
+				def saturationValue = Math.round(zigbee.convertHexToInt(zigbeeMap.value) / 255 * 100)
+				sendEvent(name: "saturation", value: saturationValue, displayed:false)
+			}
+		}
+		else {
+			log.info "DID NOT PARSE MESSAGE for description : $description"
+		}
+	}
+}
+
+def on() {
+	zigbee.on() + ["delay 1500"] + zigbee.onOffRefresh()
+}
+
+def off() {
+	zigbee.off() + ["delay 1500"] + zigbee.onOffRefresh()
+}
+
+def refresh() {
+	refreshAttributes() + configureAttributes()
+}
+
+def poll() {
+	refreshAttributes()
+}
+
+def configure() {
+	log.debug "Configuring Reporting and Bindings."
+	configureAttributes() + refreshAttributes()
+}
+
+def configureAttributes() {
+	zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE, 0x20, 1, 3600, 0x01) + zigbee.configureReporting(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION, 0x20, 1, 3600, 0x01)
+}
+
+def refreshAttributes() {
+	zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
+}
+
+def setLevel(value) {
+	zigbee.setLevel(value) + ["delay 1500"] + zigbee.levelRefresh()         //adding refresh because of ZLL bulb not conforming to send-me-a-report
+}
+
+def setColor(value){
+	log.trace "setColor($value)"
+	zigbee.on() + setHue(value.hue) + ["delay 300"] + setSaturation(value.saturation) + ["delay 2000"] + refreshAttributes()
+}
+
+def setHue(value) {
+	def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
+	zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE)      //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
+}
+
+def setSaturation(value) {
+	def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
+	zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)      //payload-> sat value, transition time
+}

devicetypes/smartthings/zll-rgbw-bulb.src/zll-rgbw-bulb.groovy

@@ -123,7 +123,7 @@ def configureAttributes() {
 }
 
 def refreshAttributes() {
-    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.readAttribute(0x0300, 0x00) + zigbee.readAttribute(0x0300, ATTRIBUTE_HUE) + zigbee.readAttribute(0x0300, ATTRIBUTE_SATURATION)
+    zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh() + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE) + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)
 }
 
 def setColorTemperature(value) {
@@ -141,10 +141,10 @@ def setColor(value){
 
 def setHue(value) {
     def scaledHueValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500")       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
+    zigbee.command(COLOR_CONTROL_CLUSTER, HUE_COMMAND, scaledHueValue, "00", "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_HUE)       //payload-> hue value, direction (00-> shortest distance), transition time (1/10th second) (0500 in U16 reads 5)
 }
 
 def setSaturation(value) {
     def scaledSatValue = zigbee.convertToHexString(Math.round(value * 0xfe / 100.0), 2)
-    zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500")      //payload-> sat value, transition time
+    zigbee.command(COLOR_CONTROL_CLUSTER, SATURATION_COMMAND, scaledSatValue, "0500") + ["delay 1500"] + zigbee.readAttribute(COLOR_CONTROL_CLUSTER, ATTRIBUTE_SATURATION)      //payload-> sat value, transition time
 }

devicetypes/smartthings/zll-white-color-temperature-bulb.src/zll-white-color-temperature-bulb.groovy

@@ -11,6 +11,9 @@
  *  for the specific language governing permissions and limitations under the License.
  *
  */
+import groovy.transform.Field
+
+@Field Boolean hasConfiguredHealthCheck = false
 
 metadata {
     definition (name: "ZLL White Color Temperature Bulb", namespace: "smartthings", author: "SmartThings") {
@@ -22,6 +25,7 @@ metadata {
         capability "Refresh"
         capability "Switch"
         capability "Switch Level"
+        capability "Health Check"
 
         attribute "colorName", "string"
         command "setGenericName"
@@ -96,9 +100,41 @@ def poll() {
     zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+    return zigbee.levelRefresh()
+}
+
+def healthPoll() {
+    log.debug "healthPoll()"
+    def cmds = zigbee.onOffRefresh() + zigbee.levelRefresh()
+    cmds.each{ sendHubCommand(new physicalgraph.device.HubAction(it))}
+}
+
+def configureHealthCheck() {
+    Integer hcIntervalMinutes = 12
+    if (!hasConfiguredHealthCheck) {
+        log.debug "Configuring Health Check, Reporting"
+        unschedule("healthPoll")
+        runEvery5Minutes("healthPoll")
+        // Device-Watch allows 2 check-in misses from device
+        sendEvent(name: "checkInterval", value: hcIntervalMinutes * 60, displayed: false, data: [protocol: "zigbee", hubHardwareId: device.hub.hardwareID])
+        hasConfiguredHealthCheck = true
+    }
+}
+
 def configure() {
-    log.debug "Configuring Reporting and Bindings."
+    log.debug "configure()"
+    configureHealthCheck()
     zigbee.onOffConfig() + zigbee.levelConfig() + zigbee.colorTemperatureConfig() + zigbee.onOffRefresh() + zigbee.levelRefresh() + zigbee.colorTemperatureRefresh()
+
+}
+
+def updated() {
+    log.debug "updated()"
+    configureHealthCheck()
 }
 
 def setColorTemperature(value) {

devicetypes/smartthings/zwave-dimmer-switch-generic.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-dimmer-switch-generic.src/README.md

@@ -0,0 +1,39 @@
+# Z-wave Dimmer
+
+
+
+Works with: 
+
+* [Leviton Plug-in Lamp Dimmer Module (DZPD3-1LW)](http://www.leviton.com/OA_HTML/ProductDetail.jsp?partnumber=DZPD3-1LW)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#troubleshooting)
+
+## Capabilities
+
+* **Switch Level** - it's defined to accept two parameters, the level and the rate of dimming
+* **Actuator** - represents that a Device has commands
+* **Health Check** - indicates ability to get device health notifications
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+
+## Device Health
+
+A Category C5 Leviton Plug-in Lamp Dimmer Module (DZPA1-1LW) (Z-Wave) polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Leviton Plug-in Lamp Dimmer Module (DZPD3-1LW) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/206171053-How-to-connect-Leviton-Z-Wave-devices)

devicetypes/smartthings/zwave-dimmer-switch-generic.src/zwave-dimmer-switch-generic.groovy

@@ -15,12 +15,14 @@ metadata {
 	definition (name: "Z-Wave Dimmer Switch Generic", namespace: "smartthings", author: "SmartThings") {
 		capability "Switch Level"
 		capability "Actuator"
+		capability "Health Check"
 		capability "Switch"
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
 
 		fingerprint inClusters: "0x26", deviceJoinName: "Z-Wave Dimmer"
+		fingerprint mfr:"001D", prod:"1902", deviceJoinName: "Z-Wave Dimmer"
 	}
 
 	simulator {
@@ -68,6 +70,11 @@ metadata {
 	}
 }
 
+def updated(){
+// Device-Watch simply pings if no device events received for 32min(checkInterval)
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description) {
 	def result = null
 	if (description != "updated") {
@@ -185,6 +192,13 @@ def poll() {
 	zwave.switchMultilevelV1.switchMultilevelGet().format()
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	log.debug "refresh() is called"
 	def commands = []

devicetypes/smartthings/zwave-switch-generic.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-switch-generic.src/README.md

@@ -0,0 +1,39 @@
+# Z-wave Switch
+
+
+
+Works with: 
+
+* [Leviton Appliance Module (DZPA1-1LW)](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
+* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave)](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Health Check** - indicates ability to get device health notifications
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+
+## Device Health
+
+A Category C5 Leviton Appliance Module (DZPA1-1LW) and GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [Leviton Appliance Module (DZPA1-1LW) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/205881176-Leviton-Appliance-Module-DZPA1-1LW-)
+* [GE Plug-In Outdoor Smart Switch (GE 12720) (Z-Wave) Troubleshooting Tips](https://support.smartthings.com/hc/en-us/articles/200903080-GE-Plug-In-Outdoor-Smart-Switch-GE-12720-Z-Wave-)

devicetypes/smartthings/zwave-switch-generic.src/zwave-switch-generic.groovy

@@ -14,12 +14,15 @@
 metadata {
 	definition (name: "Z-Wave Switch Generic", namespace: "smartthings", author: "SmartThings") {
 		capability "Actuator"
+		capability "Health Check"
  		capability "Switch"
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
 
 		fingerprint inClusters: "0x25", deviceJoinName: "Z-Wave Switch"
+		fingerprint mfr:"001D", prod:"1A02", deviceJoinName: "Z-Wave Switch"
+		fingerprint mfr:"0063", prod:"4F50", deviceJoinName: "Z-Wave Switch"
 	}
 
 	// simulator metadata
@@ -50,6 +53,11 @@ metadata {
 	}
 }
 
+def updated(){
+// Device-Watch simply pings if no device events received for checkInterval duration of 32min = 2 * 15min + 2min lag time
+	sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
+}
+
 def parse(String description) {
 	def result = null
 	def cmd = zwave.parse(description, [0x20: 1, 0x70: 1])
@@ -126,6 +134,13 @@ def poll() {
 	])
 }
 
+/**
+ * PING is used by Device-Watch in attempt to reach the Device
+ * */
+def ping() {
+	refresh()
+}
+
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),

devicetypes/smartthings/zwave-switch.src/.st-ignore

@@ -0,0 +1,2 @@
+.st-ignore
+README.md

devicetypes/smartthings/zwave-switch.src/README.md

@@ -0,0 +1,49 @@
+# Z-Wave Switch
+
+
+Works with: 
+
+* [GE Z-Wave Plug-In Smart Switch (12719)](http://products.z-wavealliance.org/products/1193)
+* [GE Z-Wave In-Wall Smart Outlet (12721)](http://products.z-wavealliance.org/products/1195)
+* [GE Z-Wave In-Wall Smart Switch (12722)](http://products.z-wavealliance.org/products/1196)
+* [GE Z-Wave In-Wall Smart Toggle Switch (12727)](http://products.z-wavealliance.org/products/1200)
+
+
+## Table of contents
+
+* [Capabilities](#capabilities)
+* [Health](#device-health)
+* [Troubleshooting](#Troubleshooting)
+
+## Capabilities
+
+* **Actuator** - represents that a Device has commands
+* **Indicator** - gives you the ability to set the indicator LED light on a Z-Wave switch
+* **Switch** - can detect state (possible values: on/off)
+* **Polling** - represents that poll() can be implemented for the device
+* **Refresh** - _refresh()_ command for status updates
+* **Sensor** - detects sensor events
+* **Health Check** - indicates ability to get device health notifications
+
+## Device Health
+
+Z-Wave Switches (Plug-In, In-Wall(Toggle Switch, Switch, Outlet)) are polled by the hub.
+As of hubCore version 0.14.38 the hub sends up reports every 15 minutes regardless of whether the state changed.
+Device-Watch allows 2 check-in misses from device plus some lag time. So Check-in interval = (2*15 + 2)mins = 32 mins.
+Not to mention after going OFFLINE when the device is plugged back in, it might take a considerable amount of time for
+the device to appear as ONLINE again. This is because if this listening device does not respond to two poll requests in a row,
+it is not polled for 5 minutes by the hub. This can delay up the process of being marked ONLINE by quite some time.
+
+
+## Troubleshooting
+
+If the device doesn't pair when trying from the SmartThings mobile app, it is possible that the device is out of range.
+Pairing needs to be tried again by placing the device closer to the hub.
+Instructions related to pairing, resetting and removing the device from SmartThings can be found in the following link:
+* [General Z-Wave Dimmer/Switch Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200955890-Troubleshooting-GE-in-wall-switch-or-dimmer-won-t-respond-to-commands-or-automations-Z-Wave-)
+* [GE Z-Wave Plug-In Smart Switch (12719) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200903070-GE-Plug-In-Smart-Switch-GE-12719-Z-Wave)
+* [GE Z-Wave In-Wall Smart Outlet (12721) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200903020-GE-In-Wall-Smart-Outlet-GE-12721-Z-Wave)
+* [GE Z-Wave In-Wall Smart Switch (12722) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/200902540-GE-In-Wall-Smart-Switch-GE-12722-Z-Wave)
+* [GE Z-Wave In-Wall Smart Toggle Switch (12727) Troubleshooting](https://support.smartthings.com/hc/en-us/articles/207568933-GE-In-Wall-Smart-Toggle-Switch-GE-12727-Z-Wave)
+
+

devicetypes/smartthings/zwave-switch.src/zwave-switch.groovy

@@ -19,6 +19,7 @@ metadata {
 		capability "Polling"
 		capability "Refresh"
 		capability "Sensor"
+		capability "Health Check"
 
 		fingerprint mfr:"0063", prod:"4952", deviceJoinName: "Z-Wave Wall Switch"
 		fingerprint mfr:"0063", prod:"5257", deviceJoinName: "Z-Wave Wall Switch"
@@ -64,6 +65,8 @@ metadata {
 }
 
 def updated(){
+		// Device-Watch simply pings if no device events received for 32min(checkInterval)
+		sendEvent(name: "checkInterval", value: 2 * 15 * 60 + 2 * 60, displayed: false, data: [protocol: "zwave", hubHardwareId: device.hub.hardwareID])
   switch (ledIndicator) {
         case "on":
             indicatorWhenOn()
@@ -156,6 +159,13 @@ def poll() {
 	])
 }
 
+/**
+  * PING is used by Device-Watch in attempt to reach the Device
+**/
+def ping() {
+		refresh()
+}
+
 def refresh() {
 	delayBetween([
 		zwave.switchBinaryV1.switchBinaryGet().format(),

smartapps/egid/smart-windows.src/smart-windows.groovy

@@ -1,7 +1,7 @@
 /**
  *  Smart Windows
  *	Compares two temperatures – indoor vs outdoor, for example – then sends an alert if windows are open (or closed!).
- * 
+ *
  *  Copyright 2014 Eric Gideon
  *
  * 	Based in part on the "When it's going to rain" SmartApp by the SmartThings team,
@@ -21,13 +21,18 @@ definition(
 	name: "Smart Windows",
 	namespace: "egid",
 	author: "Eric Gideon",
-	description: "Compares two temperatures – indoor vs outdoor, for example – then sends an alert if windows are open (or closed!). If you don't use an external temperature device, your zipcode will be used instead.",
+	description: "Compares two temperatures – indoor vs outdoor, for example – then sends an alert if windows are open (or closed!). If you don't use an external temperature device, your location will be used instead.",
 	iconUrl: "https://s3.amazonaws.com/smartthings-device-icons/Home/home9-icn.png",
 	iconX2Url: "https://s3.amazonaws.com/smartthings-device-icons/Home/home9-icn@2x.png"
 )
 
 
 preferences {
+
+  if (!(location.zipCode || ( location.latitude && location.longitude )) && location.channelName == 'samsungtv') {
+		section { paragraph title: "Note:", "Location is required for this SmartApp. Go to 'Location Name' settings to setup your correct location." }
+	}
+
 	section( "Set the temperature range for your comfort zone..." ) {
 		input "minTemp", "number", title: "Minimum temperature"
 		input "maxTemp", "number", title: "Maximum temperature"
@@ -39,9 +44,11 @@ preferences {
 		input "inTemp", "capability.temperatureMeasurement", title: "Indoor"
 		input "outTemp", "capability.temperatureMeasurement", title: "Outdoor (optional)", required: false
 	}
-	section( "Set your location" ) {
-		input "zipCode", "text", title: "Zip code"
-	}
+
+	if (location.channelName != 'samsungtv') {
+		section( "Set your location" ) { input "zipCode", "text", title: "Zip code" }
+  }
+
 	section( "Notifications" ) {
 		input "sendPushMessage", "enum", title: "Send a push notification?", metadata:[values:["Yes","No"]], required:false
 		input "retryPeriod", "number", title: "Minutes between notifications:"
@@ -72,7 +79,7 @@ def temperatureHandler(evt) {
 
 	def currentInTemp = evt.doubleValue
 	def openWindows = sensors.findAll { it?.latestValue("contact") == 'open' }
-	
+
 	log.trace "Temp event: $evt"
 	log.info "In: $currentInTemp; Out: $currentOutTemp"
 
@@ -98,7 +105,7 @@ def temperatureHandler(evt) {
 			if ( currentOutTemp < maxTemp && !openWindows ) {
 				send( "Open some windows to cool down the house! Currently ${currentInTemp}°F inside and ${currentOutTemp}°F outside." )
 			} else if ( currentOutTemp > maxTemp && openWindows ) {
-				send( "It's gotten warmer outside! You should close these windows: ${openWindows.join(', ')}. Currently ${currentInTemp}°F inside and ${currentOutTemp}°F outside." )				
+				send( "It's gotten warmer outside! You should close these windows: ${openWindows.join(', ')}. Currently ${currentInTemp}°F inside and ${currentOutTemp}°F outside." )
 			} else {
 				log.debug "No notifications sent. Everything is in the right place."
 			}
@@ -125,7 +132,11 @@ def temperatureHandler(evt) {
 }
 
 def weatherCheck() {
-	def json = getWeatherFeature("conditions", zipCode)
+	def json 
+	if (location.channelName != 'samsungtv')
+		json = getWeatherFeature("conditions", zipCode)
+	else
+		json = getWeatherFeature("conditions")
 	def currentTemp = json?.current_observation?.temp_f
 
 	if ( currentTemp ) {
@@ -150,4 +161,4 @@ private send(msg) {
 	}
 
 	log.info msg
-}
+}

smartapps/gideon-api/gideon.src/gideon.groovy

@@ -0,0 +1,253 @@
+/**
+ *  Gideon
+ *
+ *  Copyright 2016 Nicola Russo
+ *
+ *  Licensed under the Apache License, Version 2.0 (the "License"); you may not use this file except
+ *  in compliance with the License. You may obtain a copy of the License at:
+ *
+ *      http://www.apache.org/licenses/LICENSE-2.0
+ *
+ *  Unless required by applicable law or agreed to in writing, software distributed under the License is distributed
+ *  on an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. See the License
+ *  for the specific language governing permissions and limitations under the License.
+ *
+ */
+definition(
+    name: "Gideon",
+    namespace: "gideon.api",
+    author: "Braindrain Solutions",
+    description: "Gideon AI Smart app allows you to connect and control all of your SmartThings devices through the Gideon AI app, making your SmartThings devices even smarter.",
+    category: "Family",
+    iconUrl: "http://s33.postimg.org/t77u7y7v3/logo.png",
+    iconX2Url: "http://s33.postimg.org/t77u7y7v3/logo.png",
+    iconX3Url: "http://s33.postimg.org/t77u7y7v3/logo.png",
+    oauth: [displayName: "Gideon AI API", displayLink: "gideon.ai"])
+
+
+preferences {
+	section("Control these switches...") {
+        input "switches", "capability.switch", multiple:true
+    }
+    section("Control these motion sensors...") {
+        input "motions", "capability.motionSensor", multiple:true
+    }
+    section("Control these presence sensors...") {
+    	input "presence_sensors", "capability.presenceSensor", multiple:true
+    }
+    section("Control these outlets...") {
+    	input "outlets", "capability.switch", multiple:true
+    }
+    section("Control these locks...") {
+    	input "locks", "capability.lock", multiple:true
+    }
+    section("Control these locks...") {
+	    input "temperature_sensors", "capability.temperatureMeasurement"
+    }
+}
+
+def installed() {
+	log.debug "Installed with settings: ${settings}"
+
+	initialize()
+}
+
+def updated() {
+	log.debug "Updated with settings: ${settings}"
+
+	unsubscribe()
+	initialize()
+}
+
+def initialize() {
+	// TODO: subscribe to attributes, devices, locations, etc.
+    subscribe(outlet, "energy", outletHandler)
+  	subscribe(outlet, "switch", outletHandler)
+}
+
+// TODO: implement event handlers
+def outletHandler(evt) {
+	log.debug "$outlet.currentEnergy"
+	//TODO call G API  
+}
+
+
+private device(it, type) {
+	it ? [id: it.id, label: it.label, type: type] : null
+}
+
+//API Mapping
+mappings {
+	path("/getalldevices") {
+    action: [
+      			GET: "getAllDevices"
+    		]
+  	}
+	path("/doorlocks/:id/:command") {
+    action: [
+      GET: "updateDoorLock"
+    ]
+  }
+  	path("/doorlocks/:id") {
+    action: [
+      			GET: "getDoorLockStatus"
+    		]
+  	}
+  	path("/tempsensors/:id") {
+    action: [
+      GET: "getTempSensorsStatus"
+    ]
+  }
+  	path("/presences/:id") {
+    action: [
+      GET: "getPresenceStatus"
+    ]
+  }
+  	path("/motions/:id") {
+    action: [
+      GET: "getMotionStatus"
+    ]
+  }
+  	path("/outlets/:id") {
+    action: [
+      GET: "getOutletStatus"
+    ]
+  }
+  	path("/outlets/:id/:command") {
+    action: [
+      GET: "updateOutlet"
+    ]
+  }
+  	path("/switches/:command") {
+    action: [
+      PUT: "updateSwitch"
+    ]
+  }
+}
+
+//API Methods
+def getAllDevices() {
+	def locks_list = locks.collect{device(it,"Lock")}
+    def presences_list = presence_sensors.collect{device(it,"Presence")}
+    def motions_list = motions.collect{device(it,"Motion")}
+    def outlets_list = outlets.collect{device(it,"Outlet")}
+    def switches_list = switches.collect{device(it,"Switch")}
+    def temp_list = temperature_sensors.collect{device(it,"Temperature")}
+    return [Locks: locks_list, Presences: presences_list, Motions: motions_list, Outlets: outlets_list, Switches: switches_list, Temperatures: temp_list]
+}
+
+//LOCKS
+def getDoorLockStatus() {
+	def device = locks.find { it.id == params.id }
+    if (!device) {
+            httpError(404, "Device not found")
+        } else {
+        	return [Device_state: device.currentValue('lock')]
+        }
+}
+
+def updateDoorLock() {
+	def command = params.command
+    def device = locks.find { it.id == params.id }
+    if (command){
+        if (!device) {
+            httpError(404, "Device not found")
+        } else {
+            if(command == "toggle")
+            {
+                if(device.currentValue('lock') == "locked")
+                  device.unlock();
+                else
+                  device.lock();
+                  
+                return [Device_id: params.id, result_action: "200"]
+            }
+        }
+    }
+}
+
+//PRESENCE
+def getPresenceStatus() {
+
+	def device = presence_sensors.find { it.id == params.id }
+    if (!device) {
+            httpError(404, "Device not found")
+        } else {
+        	return [Device_state: device.currentValue('presence')]
+   }
+}
+
+//MOTION
+def getMotionStatus() {
+
+	def device = motions.find { it.id == params.id }
+    if (!device) {
+            httpError(404, "Device not found")
+        } else {
+        	return [Device_state: device.currentValue('motion')]
+   }
+}
+
+//OUTLET
+def getOutletStatus() {
+	
+    def device = outlets.find { it.id == params.id }
+   	if (!device) {
+            httpError(404, "Device not found")
+        } else {
+        	return [Device_state: device.currentSwitch, Current_watt: device.currentValue("energy")]
+  }
+}
+
+def updateOutlet() {
+	
+    def command = params.command
+    def device = outlets.find { it.id == params.id }
+    if (command){
+        if (!device) {
+            httpError(404, "Device not found")
+        } else {
+            if(command == "toggle")
+            {
+                if(device.currentSwitch == "on")
+                  device.off();
+                else
+                  device.on();
+                  
+                return [Device_id: params.id, result_action: "200"]
+            }
+        }
+    }
+}                
+
+//SWITCH
+def updateSwitch() {
+    def command = params.command
+    def device = switches.find { it.id == params.id }
+    if (command){
+        if (!device) {
+            httpError(404, "Device not found")
+        } else {
+            if(command == "toggle")
+            {
+                if(device.currentSwitch == "on")
+                  device.off();
+                else
+                  device.on();
+                  
+                return [Device_id: params.id, result_action: "200"]
+            }
+        }
+    }
+}
+
+//TEMPERATURE
+def getTempSensorsStatus() {
+	
+    def device = temperature_sensors.find { it.id == params.id }
+    if (!device) {
+            httpError(404, "Device not found")
+        } else {
+        	return [Device_state: device.currentValue('temperature')]
+   }
+}

smartapps/imbrianj/ready-for-rain.src/ready-for-rain.groovy

@@ -18,8 +18,13 @@ definition(
 )
 
 preferences {
-  section("Zip code?") {
-    input "zipcode", "text", title: "Zipcode?"
+
+  if (!(location.zipCode || ( location.latitude && location.longitude )) && location.channelName == 'samsungtv') {
+		section { paragraph title: "Note:", "Location is required for this SmartApp. Go to 'Location Name' settings to setup your correct location." }
+	}
+
+  if (location.channelName != 'samsungtv') {
+		section( "Set your location" ) { input "zipCode", "text", title: "Zip code" }
   }
 
   section("Things to check?") {
@@ -60,7 +65,11 @@ def scheduleCheck(evt) {
   // Only need to poll if we haven't checked in a while - and if something is left open.
   if((now() - (30 * 60 * 1000) > state.lastCheck["time"]) && open) {
     log.info("Something's open - let's check the weather.")
-    def response = getWeatherFeature("forecast", zipcode)
+    def response
+    if (location.channelName != 'samsungtv')
+      response = getWeatherFeature("forecast", zipCode)
+    else
+      response = getWeatherFeature("forecast")
     def weather  = isStormy(response)
 
     if(weather) {

smartapps/juano2310/jawbone-up-connect.src/jawbone-up-connect.groovy

@@ -4,6 +4,9 @@
  *  Author: Juan Risso
  *  Date: 2013-12-19
  */
+
+include 'asynchttp_v1'
+
 definition(
 	name: "Jawbone UP (Connect)",
 	namespace: "juano2310",
@@ -28,7 +31,7 @@ mappings {
 	path("/receivedToken") { action: [ POST: "receivedToken", GET: "receivedToken"] }
 	path("/receiveToken") { action: [ POST: "receiveToken", GET: "receiveToken"] }
 	path("/hookCallback") { action: [ POST: "hookEventHandler", GET: "hookEventHandler"] }
-    path("/oauth/initialize") {action: [GET: "oauthInitUrl"]}    
+  path("/oauth/initialize") {action: [GET: "oauthInitUrl"]}
 	path("/oauth/callback") { action: [ GET: "callback" ] }
 }
 
@@ -44,7 +47,7 @@ def callback() {
 	} else {
 		log.warn "No authQueryString"
 	}
-	
+
 	if (state.JawboneAccessToken) {
 		log.debug "Access token already exists"
 		setup()
@@ -73,7 +76,7 @@ def callback() {
 
 def authPage() {
     log.debug "authPage"
-    def description = null          
+    def description = null
     if (state.JawboneAccessToken == null) {
 		if (!state.accessToken) {
 			log.debug "About to create access token"
@@ -82,12 +85,13 @@ def authPage() {
         description = "Click to enter Jawbone Credentials"
         def redirectUrl = buildRedirectUrl
         log.debug "RedirectURL = ${redirectUrl}"
-        def donebutton= state.JawboneAccessToken != null 
+        def donebutton= state.JawboneAccessToken != null
         return dynamicPage(name: "Credentials", title: "Jawbone UP", nextPage: null, uninstall: true, install: donebutton) {
+							 section { paragraph title: "Note:", "This device has not been officially tested and certified to “Work with SmartThings”. You can connect it to your SmartThings home but performance may vary and we will not be able to provide support or assistance." }
                section { href url:redirectUrl, style:"embedded", required:true, title:"Jawbone UP", state: hast ,description:description }
         }
     } else {
-        description = "Jawbone Credentials Already Entered." 
+        description = "Jawbone Credentials Already Entered."
         return dynamicPage(name: "Credentials", title: "Jawbone UP", uninstall: true, install:true) {
                section { href url: buildRedirectUrl("receivedToken"), style:"embedded", state: "complete", title:"Jawbone UP", description:description }
         }
@@ -107,7 +111,7 @@ def receiveToken(redirectUrl = null) {
     def params = [
       uri: "https://jawbone.com/auth/oauth2/token?${toQueryString(oauthParams)}",
     ]
-    httpGet(params) { response -> 
+    httpGet(params) { response ->
     	log.debug "${response.data}"
 		log.debug "Setting access token to ${response.data.access_token}, refresh token to ${response.data.refresh_token}"
     	state.JawboneAccessToken = response.data.access_token
@@ -149,7 +153,7 @@ def connectionStatus(message, redirectUrl = null) {
 			<meta http-equiv="refresh" content="3; url=${redirectUrl}" />
 		"""
 	}
-	
+
     def html = """
         <!DOCTYPE html>
         <html>
@@ -229,12 +233,12 @@ def validateCurrentToken() {
 	log.debug "validateCurrentToken"
     def url = "https://jawbone.com/nudge/api/v.1.1/users/@me/refreshToken"
     def requestBody = "secret=${appSettings.clientSecret}"
-	
+
 	try {
 		httpPost(uri: url, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ],  body: requestBody) {response ->
 	    	if (response.status == 200) {
 				log.debug "${response.data}"
-				log.debug "Setting refresh token to ${response.data.data.refresh_token}"
+				log.debug "Setting refresh token"
 	     		state.refreshToken = response.data.data.refresh_token
 	        }
 	    }
@@ -258,7 +262,7 @@ def validateCurrentToken() {
 							state.remove("refreshToken")
 						}
 					} else {
-						log.debug "Setting access token to ${data.access_token}, refresh token to ${data.refresh_token}"
+						log.debug "Setting access token"
 						state.JawboneAccessToken = data.access_token
 						state.refreshToken = data.refresh_token
 					}
@@ -271,10 +275,10 @@ def validateCurrentToken() {
 }
 
 def initialize() {
-    log.debug "Callback URL - Webhook"  
-	def localServerUrl = getApiServerUrl() 
+    log.debug "Callback URL - Webhook"
+	def localServerUrl = getApiServerUrl()
 	def hookUrl = "${localServerUrl}/api/token/${state.accessToken}/smartapps/installations/${app.id}/hookCallback"
-    def webhook = "https://jawbone.com/nudge/api/v.1.1/users/@me/pubsub?webhook=$hookUrl"      
+    def webhook = "https://jawbone.com/nudge/api/v.1.1/users/@me/pubsub?webhook=$hookUrl"
 	httpPost(uri: webhook, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ])
 }
 
@@ -284,16 +288,16 @@ def setup() {
 
 	if (state.JawboneAccessToken) {
 		def urlmember = "https://jawbone.com/nudge/api/users/@me/"
-		def member = null    
-		httpGet(uri: urlmember, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response -> 
+		def member = null
+		httpGet(uri: urlmember, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response ->
 		    member = response.data.data
 		}
-	
+
 		if (member) {
 			state.member = member
 			def externalId = "${app.id}.${member.xid}"
 
-			// find the appropriate child device based on my app id and the device network id 
+			// find the appropriate child device based on my app id and the device network id
 			def deviceWrapper = getChildDevice("${externalId}")
 
 			// invoke the generatePresenceEvent method on the child device
@@ -302,7 +306,8 @@ def setup() {
 			  	def childDevice = addChildDevice('juano2310', "Jawbone User", "${app.id}.${member.xid}",null,[name:"Jawbone UP - " + member.first, completedSetup: true])
 			    if (childDevice) {
 			       	log.debug "Child Device Successfully Created"
-			        generateInitialEvent (member, childDevice)
+			        childDevice?.generateSleepingEvent(false)
+                    pollChild(childDevice)
 			    }
 			}
 		}
@@ -312,7 +317,7 @@ def setup() {
 }
 
 def installed() {
-	
+
 	if (!state.accessToken) {
 		log.debug "About to create access token"
 		createAccessToken()
@@ -324,7 +329,7 @@ def installed() {
 }
 
 def updated() {
-	
+
 	if (!state.accessToken) {
 		log.debug "About to create access token"
 		createAccessToken()
@@ -348,128 +353,128 @@ def uninstalled() {
 }
 
 def pollChild(childDevice) {
-    def member = state.member 
-    generatePollingEvents (member, childDevice)   
+		def childMap = [ value: "$childDevice.device.deviceNetworkId}"]
+
+		def params = [
+				uri: 'https://jawbone.com',
+				path: '/nudge/api/users/@me/goals',
+				headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ],
+				contentType: 'application/json'
+		]
+
+		asynchttp_v1.get('responseGoals', params, childMap)
+
+		def params2 = [
+				uri: 'https://jawbone.com',
+				path: '/nudge/api/users/@me/moves',
+				headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ],
+				contentType: 'application/json'
+		]
+
+		asynchttp_v1.get('responseMoves', params2, childMap)
 }
 
-def generatePollingEvents (member, childDevice) {
-    // lets figure out if the member is currently "home" (At the place)
-    def urlgoals = "https://jawbone.com/nudge/api/users/@me/goals" 
-    def urlmoves = "https://jawbone.com/nudge/api/users/@me/moves"  
-    def urlsleeps = "https://jawbone.com/nudge/api/users/@me/sleeps"     
-    def goals = null
-    def moves = null
- 	def sleeps = null   
-    httpGet(uri: urlgoals, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response -> 
-        goals = response.data.data
-    }   
-    httpGet(uri: urlmoves, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response -> 
-        moves = response.data.data.items[0]
-    }    
-   
-    try { // we are going to just ignore any errors
-        log.debug "Member = ${member.first}"
-        log.debug "Moves Goal = ${goals.move_steps} Steps"
-        log.debug "Moves = ${moves.details.steps} Steps" 
-
-        childDevice?.sendEvent(name:"steps", value: moves.details.steps)
-        childDevice?.sendEvent(name:"goal", value: goals.move_steps)
-    	//setColor(moves.details.steps,goals.move_steps,childDevice)
-    }
-    catch (e) {
-            // eat it
-    }       
+def responseGoals(response, dni) {
+	if (response.hasError()) {
+			log.error "response has error: $response.errorMessage"
+	} else {
+			def goals
+			try {
+					// json response already parsed into JSONElement object
+					goals = response.json.data
+			} catch (e) {
+					log.error "error parsing json from response: $e"
+			}
+			if (goals) {
+				def childDevice = getChildDevice(dni.value)
+				log.debug "Goal = ${goals.move_steps} Steps"
+				childDevice?.sendEvent(name:"goal", value: goals.move_steps)
+			} else {
+					log.debug "did not get json results from response body: $response.data"
+			}
+	}
 }
 
-def generateInitialEvent (member, childDevice) {
-    // lets figure out if the member is currently "home" (At the place)
-    def urlgoals = "https://jawbone.com/nudge/api/users/@me/goals" 
-    def urlmoves = "https://jawbone.com/nudge/api/users/@me/moves"  
-    def urlsleeps = "https://jawbone.com/nudge/api/users/@me/sleeps"     
-    def goals = null
-    def moves = null
- 	def sleeps = null   
-    httpGet(uri: urlgoals, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response -> 
-        goals = response.data.data
-    }   
-    httpGet(uri: urlmoves, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response -> 
-        moves = response.data.data.items[0]
-    }    
-    
-    try { // we are going to just ignore any errors
-        log.debug "Member = ${member.first}"
-        log.debug "Moves Goal = ${goals.move_steps} Steps"
-        log.debug "Moves = ${moves.details.steps} Steps"
-        log.debug "Sleeping state = false"   
-        childDevice?.generateSleepingEvent(false)
-        childDevice?.sendEvent(name:"steps", value: moves.details.steps)
-        childDevice?.sendEvent(name:"goal", value: goals.move_steps)
-    	//setColor(moves.details.steps,goals.move_steps,childDevice)
-    }
-    catch (e) {
-            // eat it
-    }       
+def responseMoves(response, dni) {
+	if (response.hasError()) {
+			log.error "response has error: $response.errorMessage"
+	} else {
+			def moves
+			try {
+					// json response already parsed into JSONElement object
+					moves = response.json.data.items[0]
+			} catch (e) {
+					log.error "error parsing json from response: $e"
+			}
+			if (moves) {
+				def childDevice = getChildDevice(dni.value)
+				log.debug "Moves = ${moves.details.steps} Steps"
+				childDevice?.sendEvent(name:"steps", value: moves.details.steps)
+			} else {
+					log.debug "did not get json results from response body: $response.data"
+			}
+	}
 }
 
 def setColor (steps,goal,childDevice) {
     def result = steps * 100 / goal
-    if (result < 25) 
+    if (result < 25)
     	childDevice?.sendEvent(name:"steps", value: "steps", label: steps)
-    else if ((result >= 25) && (result < 50)) 
+    else if ((result >= 25) && (result < 50))
         childDevice?.sendEvent(name:"steps", value: "steps1", label: steps)
-    else if ((result >= 50) && (result < 75)) 
+    else if ((result >= 50) && (result < 75))
         childDevice?.sendEvent(name:"steps", value: "steps1", label: steps)
-    else if (result >= 75)     
-        childDevice?.sendEvent(name:"steps", value: "stepsgoal", label: steps)   
+    else if (result >= 75)
+        childDevice?.sendEvent(name:"steps", value: "stepsgoal", label: steps)
 }
 
 def hookEventHandler() {
     // log.debug "In hookEventHandler method."
     log.debug "request = ${request}"
-    
-    def json = request.JSON 
-    
+
+    def json = request.JSON
+
     // get some stuff we need
     def userId = json.events.user_xid[0]
     def	json_type = json.events.type[0]
-	def json_action = json.events.action[0]
+	  def json_action = json.events.action[0]
 
     //log.debug json
     log.debug "Userid = ${userId}"
     log.debug "Notification Type: " + json_type
-    log.debug "Notification Action: " + json_action 
-    
+    log.debug "Notification Action: " + json_action
+
     // find the appropriate child device based on my app id and the device network id
     def externalId = "${app.id}.${userId}"
     def childDevice = getChildDevice("${externalId}")
-            
+
     if (childDevice) {
-    	switch (json_action) {   
-	        case "enter_sleep_mode":      
-            	childDevice?.generateSleepingEvent(true)           
-                break           
-            case "exit_sleep_mode":       
-            	childDevice?.generateSleepingEvent(false) 
-                break 
-            case "creation": 
+    	switch (json_action) {
+	        case "enter_sleep_mode":
+            	childDevice?.generateSleepingEvent(true)
+                break
+            case "exit_sleep_mode":
+            	childDevice?.generateSleepingEvent(false)
+                break
+            case "creation":
                 childDevice?.sendEvent(name:"steps", value: 0)
           		break
             case "updation":
-                def urlgoals = "https://jawbone.com/nudge/api/users/@me/goals"     
-                def urlmoves = "https://jawbone.com/nudge/api/users/@me/moves"       
+                def urlgoals = "https://jawbone.com/nudge/api/users/@me/goals"
+                def urlmoves = "https://jawbone.com/nudge/api/users/@me/moves"
                 def goals = null
-                def moves = null    
-                httpGet(uri: urlgoals, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response -> 
+                def moves = null
+                httpGet(uri: urlgoals, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response ->
  	               goals = response.data.data
-                }       
-                httpGet(uri: urlmoves, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response -> 
+                }
+                httpGet(uri: urlmoves, headers: ["Authorization": "Bearer ${state.JawboneAccessToken}" ]) {response ->
                    moves = response.data.data.items[0]
-                }        
+                }
                 log.debug "Goal = ${goals.move_steps} Steps"
-        		log.debug "Steps = ${moves.details.steps} Steps"
+        				log.debug "Steps = ${moves.details.steps} Steps"
                 childDevice?.sendEvent(name:"steps", value: moves.details.steps)
-                childDevice?.sendEvent(name:"goal", value: goals.move_steps)       
-                //setColor(moves.details.steps,goals.move_steps,childDevice)   
+                childDevice?.sendEvent(name:"goal", value: goals.move_steps)
+                //setColor(moves.details.steps,goals.move_steps,childDevice)
                 break
 			case "deletion":
 				app.delete()

smartapps/smartthings/ecobee-connect.src/ecobee-connect.groovy

@@ -20,8 +20,6 @@
  *      JLH - 02-15-2014 - Fuller use of ecobee API
  *      10-28-2015 DVCSMP-604 - accessory sensor, DVCSMP-1174, DVCSMP-1111 - not respond to routines
  */
-include 'asynchttp_v1'
-
 definition(
 		name: "Ecobee (Connect)",
 		namespace: "smartthings",
@@ -246,7 +244,9 @@ def getEcobeeThermostats() {
 		uri: apiEndpoint,
 		path: "/1/thermostat",
 		headers: ["Content-Type": "text/json", "Authorization": "Bearer ${atomicState.authToken}"],
-		query: [json: toJson(bodyParams)]
+        // TODO - the query string below is not consistent with the Ecobee docs:
+        // https://www.ecobee.com/home/developer/api/documentation/v1/operations/get-thermostats.shtml
+		query: [format: 'json', body: toJson(bodyParams)]
 	]
 
 	def stats = [:]
@@ -265,8 +265,9 @@ def getEcobeeThermostats() {
 	} catch (groovyx.net.http.HttpResponseException e) {
         log.trace "Exception polling children: " + e.response.data.status
         if (e.response.data.status.code == 14) {
+            atomicState.action = "getEcobeeThermostats"
             log.debug "Refreshing your auth_token!"
-            refreshAuthToken([async: false, nextAction: "getEcobeeThermostats"])
+            refreshAuthToken()
         }
     }
 	atomicState.thermostats = stats
@@ -357,22 +358,16 @@ def initialize() {
 	atomicState.timeSendPush = null
 	atomicState.reAttempt = 0
 
-	initialPoll() //first time polling data data from thermostat
+	pollHandler() //first time polling data data from thermostat
 
 	//automatically update devices status every 5 mins
 	runEvery5Minutes("poll")
 
 }
 
-/**
- * Polls the child devices (synchronously).
- * This is used during app install/update, and is synchronous
- * to maintain current behavior that will cause install/update to fail
- * if polling fails.
- */
-def initialPoll() {
-	log.debug "initialPoll()"
-	pollChildrenSync() // Hit the ecobee API for update on all thermostats
+def pollHandler() {
+	log.debug "pollHandler()"
+	pollChildren(null) // Hit the ecobee API for update on all thermostats
 
 	atomicState.thermostats.each {stat ->
 		def dni = stat.key
@@ -385,101 +380,10 @@ def initialPoll() {
 	}
 }
 
-/**
- * Polls Ecobee (asynchronously) for updated device state data.
- * Called from within this Connect SmartApp as well as the child
- * devices.
- */
-def poll() {
-    log.debug "polling asynchronously"
-    asynchttp_v1.get('asyncPollResponseHandler', getPollParams())
-}
-
-/**
- * Makes a (synchronous) request to the Ecobee API to get the data for the thermostats.
- * This request is made synchronously here because it is called as part of the
- * install/updated lifecycle, and changing it to asynchronous during the install/update
- * lifecycle may change the behavior if there is an error in polling.
- *
- * If further analysis shows that polling can be done asynchronously during
- * install/update without any adverse consequences, this should then be made
- * asynchronous just as the scheduled polling is.
- */
-def pollChildrenSync() {
+def pollChildren(child = null) {
+    def thermostatIdsString = getChildDeviceIdsString()
     log.debug "polling children: $thermostatIdsString"
 
-    def params = getPollParams()
-    params.query << ["Content-Type": "application/json"]
-
-	def result = false
-    log.debug "making synchronous poll request"
-
-	try{
-		httpGet(params) { resp ->
-			if(resp.status == 200) {
-                atomicState.remoteSensors = resp.data.thermostatList.remoteSensors
-                updateSensorData()
-                storeThermostatData(resp.data.thermostatList)
-                result = true
-                log.debug "updated ${atomicState.thermostats?.size()} stats: ${atomicState.thermostats}"
-            }
-		}
-	} catch (groovyx.net.http.HttpResponseException e) {
-		log.trace "Exception polling children: " + e.response.data.status
-        if (e.response.data.status.code == 14) {
-            log.debug "Refreshing your auth_token!"
-            refreshAuthToken([async: false, nextAction: "pollChildrenSync"])
-        }
-	}
-	return result
-}
-
-/**
- * Response handler for asynchronous request to get thermostat data.
- * Given a successful response, updates the sensor data, stores the thermostat
- * data, and generates child device events.
- *
- * If the access token has expired, will issue a request to refresh the token
- * (and pending successful token refresh, the poll request will be made again).
- */
-def asyncPollResponseHandler(response, data) {
-    log.trace "async poll response handler"
-    if (!response.hasError()) {
-        if (response.status == 200) {
-            def json
-            try {
-                json = response.getJson()
-            } catch (e) {
-                log.error ("error parsing JSON", e)
-            }
-            if (json) {
-                atomicState.remoteSensors = json.thermostatList.remoteSensors
-                updateSensorData()
-                storeThermostatData(json.thermostatList)
-                generateChildThermostatEvent()
-            }
-        } else {
-            log.warn "Response returned non-200 response. Status: ${response.status}, data: ${response.getData()}"
-        }
-    } else {
-        log.trace "Exception polling children: ${response.getErrorMessage()}"
-        def errorJson
-        try {
-            errorJson = response.getErrorJson()
-        } catch (e) {
-            log.error("Unable to parse error json response", e)
-        }
-        if (errorJson?.status?.code == 14) {
-            log.debug "Refreshing your auth_token!"
-            refreshAuthToken([async: true, nextAction: "poll"])
-        } else {
-            log.warn "Error polling children that is not due to an expired token. Response: ${response.getErrorData()}"
-        }
-    }
-}
-
-private getPollParams() {
-    def thermostatIdsString = getChildDeviceIdsString()
     def requestBody = [
         selection: [
             selectionType: "thermostats",
@@ -490,32 +394,66 @@ private getPollParams() {
             includeSensors: true
         ]
     ]
-    return [
+
+	def result = false
+
+	def pollParams = [
         uri: apiEndpoint,
         path: "/1/thermostat",
-        headers: ["Authorization": "Bearer ${atomicState.authToken}"],
-        query: [json: toJson(requestBody)]
+        headers: ["Content-Type": "text/json", "Authorization": "Bearer ${atomicState.authToken}"],
+        // TODO - the query string below is not consistent with the Ecobee docs:
+        // https://www.ecobee.com/home/developer/api/documentation/v1/operations/get-thermostats.shtml
+        query: [format: 'json', body: toJson(requestBody)]
     ]
+
+	try{
+		httpGet(pollParams) { resp ->
+			if(resp.status == 200) {
+                log.debug "poll results returned resp.data ${resp.data}"
+                atomicState.remoteSensors = resp.data.thermostatList.remoteSensors
+                updateSensorData()
+                storeThermostatData(resp.data.thermostatList)
+                result = true
+                log.debug "updated ${atomicState.thermostats?.size()} stats: ${atomicState.thermostats}"
+            }
+		}
+	} catch (groovyx.net.http.HttpResponseException e) {
+		log.trace "Exception polling children: " + e.response.data.status
+        if (e.response.data.status.code == 14) {
+            atomicState.action = "pollChildren"
+            log.debug "Refreshing your auth_token!"
+            refreshAuthToken()
+        }
+	}
+	return result
 }
 
-/**
- * Calls each child thermostat device to generate an event with the thermostat
- * data.
- */
-def generateChildThermostatEvent() {
-    log.trace("generateChildThermostatEvent")
-    getChildDevices().each { child ->
-        if (!child.device.deviceNetworkId.startsWith("ecobee_sensor")){
-            if(atomicState.thermostats[child.device.deviceNetworkId] != null) {
-                def tData = atomicState.thermostats[child.device.deviceNetworkId]
-                log.debug "calling child.generateEvent($tData.data)"
-                child.generateEvent(tData.data) //parse received message from parent
-            } else if(atomicState.thermostats[child.device.deviceNetworkId] == null) {
-                log.error "ERROR: Device connection removed? no data for ${child.device.deviceNetworkId}"
-                return null
-            }
-        }
-    }
+// Poll Child is invoked from the Child Device itself as part of the Poll Capability
+def pollChild() {
+	def devices = getChildDevices()
+
+	if (pollChildren()) {
+		devices.each { child ->
+			if (!child.device.deviceNetworkId.startsWith("ecobee_sensor")) {
+				if(atomicState.thermostats[child.device.deviceNetworkId] != null) {
+					def tData = atomicState.thermostats[child.device.deviceNetworkId]
+					log.info "pollChild(child)>> data for ${child.device.deviceNetworkId} : ${tData.data}"
+					child.generateEvent(tData.data) //parse received message from parent
+				} else if(atomicState.thermostats[child.device.deviceNetworkId] == null) {
+					log.error "ERROR: Device connection removed? no data for ${child.device.deviceNetworkId}"
+					return null
+				}
+			}
+		}
+	} else {
+		log.info "ERROR: pollChildren()"
+		return null
+	}
+
+}
+
+void poll() {
+	pollChild()
 }
 
 def availableModes(child) {
@@ -615,104 +553,47 @@ def toQueryString(Map m) {
 	return m.collect { k, v -> "${k}=${URLEncoder.encode(v.toString())}" }.sort().join("&")
 }
 
-/**
- * Uses the refresh token to get a new access token, then executes the nextAction.
- * @param options - a map of options. valid options are async: true/false, which
- *                  specifies if the refresh token request will be done asynchronously or not (default is false)
- *                  nextAction: "nameOfMethod" specifies what method to execute after
- *                  the token is refreshed (not required).
- * (note: using a map as the parameter because we need to call it from a schedueled
- * execution and we can only pass a data map to scheduled executions)
- */
-private void refreshAuthToken(options) {
-    if(!atomicState.refreshToken) {
-		log.warn "Cannot not refresh OAuth token since there is no refreshToken stored"
-    } else {
-        def refreshParams = [
-            uri   : apiEndpoint,
-            path  : "/token",
-            query : [grant_type: 'refresh_token', code: "${atomicState.refreshToken}", client_id: smartThingsClientId],
-        ]
-        if (options.async) {
-            refreshAuthTokenAsync(refreshParams, options.nextAction)
-        } else {
-            refreshAuthTokenSync(refreshParams, options.nextAction)
-        }
-    }
-}
+private refreshAuthToken() {
+	log.debug "refreshing auth token"
 
-private void refreshAuthTokenSync(params, nextAction = null) {
-    try {
-        httpPost(refreshParams) { resp ->
-            if(resp.status == 200) {
-                log.debug "Token refreshed...calling saved RestAction now!"
-                debugEvent("Token refreshed ... calling saved RestAction now!")
-                saveTokenAndResumeAction(resp.data, nextAction)
+	if(!atomicState.refreshToken) {
+		log.warn "Can not refresh OAuth token since there is no refreshToken stored"
+	} else {
+		def refreshParams = [
+			method: 'POST',
+			uri   : apiEndpoint,
+			path  : "/token",
+			query : [grant_type: 'refresh_token', code: "${atomicState.refreshToken}", client_id: smartThingsClientId],
+		]
+
+		def notificationMessage = "is disconnected from SmartThings, because the access credential changed or was lost. Please go to the Ecobee (Connect) SmartApp and re-enter your account login credentials."
+		//changed to httpPost
+		try {
+			def jsonMap
+			httpPost(refreshParams) { resp ->
+				if(resp.status == 200) {
+					log.debug "Token refreshed...calling saved RestAction now!"
+					debugEvent("Token refreshed ... calling saved RestAction now!")
+					saveTokenAndResumeAction(resp.data)
+			    }
             }
-        }
-    } catch (groovyx.net.http.HttpResponseException e) {
-        log.error "refreshAuthToken() >> Error: e.statusCode ${e.statusCode}"
-        reauthTokenErrorHandler(e.statusCode)
-    }
-}
-
-private void refreshAuthTokenAsync(refreshParams, nextAction = null) {
-    log.debug "making asynchronous refresh request"
-    asynchttp_v1.post('refreshTokenResponseHandler', refreshParams, [nextAction: nextAction])
-}
-
-/**
- * The response handler for the request to refresh the authorization handler.
- * Stores the new authorization token and refresh token, and executes any action
- * (method) that failed due to the authorization token expiring.
- */
-private void refreshTokenResponseHandler(response, data) {
-    if (!response.hasError()) {
-        if (response.status == 200) {
-            def json
-            try {
-            	json = response.getJson()
-            } catch (e) {
-            	log.error "error parsing json from response data: $response.data"
-            }
-            if (json) {
-                log.debug "asnyc refreshTokenHandler: Token refreshed...calling saved RestAction now!"
-                debugEvent("async Token refreshed ... calling saved RestAction now!")
-             	saveTokenAndResumeAction(json, data.nextAction)
-            } else {
-            	log.warn "successfully parsed json but result is empty or null"
-            }
-        } else {
-            log.debug "Non 200 response returned. Response code: ${response.code}, data: ${response.getData()}"
-        }
-    } else {
-        log.debug "async refreshTokenHandler: RESPONSE ERROR: ${response.getErrorJson()}"
-        reauthTokenErrorHandler(response.getErrorJson().code)
-    }
-}
-
-/**
- * Retries refreshing the authorization token. Will attempt to get the refresh
- * token later, in case there were errors retrieving it.
- * Will retry a fixed number of times before sending a push notification to the
- * user instructing them to reauthenticate
- */
-private void reauthTokenErrorHandler(responseCode) {
-    def retryInterval = 300 // in seconds
-    def notificationMessage = "is disconnected from SmartThings, because the access credential changed or was lost. Please go to the Ecobee (Connect) SmartApp and re-enter your account login credentials."
-    // might get non-401 error from exceeding 20 second app limit, connectivity issues, etc.
-    if (responseCode != 401) {
-        runIn(retryInterval, "refreshAuthToken", [async: true])
-    } else if (responseCode == 401) { // unauthorized
-        atomicState.reAttempt = atomicState.reAttempt + 1
-        log.warn "reAttempt refreshAuthToken to try = ${atomicState.reAttempt}"
-        if (atomicState.reAttempt <= 3) {
-            runIn(retryInterval, "refreshAuthToken", [async: true])
-        } else {
-            sendPushAndFeeds(notificationMessage)
-            atomicState.reAttempt = 0
-        }
-    }
+		} catch (groovyx.net.http.HttpResponseException e) {
+			log.error "refreshAuthToken() >> Error: e.statusCode ${e.statusCode}"
+			def reAttemptPeriod = 300 // in sec
+			if (e.statusCode != 401) { // this issue might comes from exceed 20sec app execution, connectivity issue etc.
+				runIn(reAttemptPeriod, "refreshAuthToken")
+			} else if (e.statusCode == 401) { // unauthorized
+				atomicState.reAttempt = atomicState.reAttempt + 1
+				log.warn "reAttempt refreshAuthToken to try = ${atomicState.reAttempt}"
+				if (atomicState.reAttempt <= 3) {
+					runIn(reAttemptPeriod, "refreshAuthToken")
+				} else {
+					sendPushAndFeeds(notificationMessage)
+					atomicState.reAttempt = 0
+				}
+			}
+		}
+	}
 }
 
 /**
@@ -722,20 +603,20 @@ private void reauthTokenErrorHandler(responseCode) {
  *
  * @param json - an object representing the parsed JSON response from Ecobee
  */
-private void saveTokenAndResumeAction(json, String nextAction) {
-    def debugMessage = "token response, scope: ${json?.scope}, expires_in: ${json?.expires_in}, token_type: ${json?.token_type}"
-    log.debug "debugMessage"
+private void saveTokenAndResumeAction(json) {
+    log.debug "token response json: $json"
     if (json) {
-        debugEvent(debugMessage)
+        debugEvent("Response = $json")
         atomicState.refreshToken = json?.refresh_token
         atomicState.authToken = json?.access_token
-        if (nextAction) {
-            log.debug "got refresh token, will execute next action (passed in!): $nextAction"
-            "$nextAction"()
+        if (atomicState.action) {
+            log.debug "got refresh token, executing next action: ${atomicState.action}"
+            "${atomicState.action}"()
         }
     } else {
         log.warn "did not get response body from refresh token response"
     }
+    atomicState.action = ""
 }
 
 /**
@@ -875,6 +756,7 @@ private boolean sendCommandToEcobee(Map bodyParams) {
 	try{
         httpPost(cmdParams) { resp ->
             if(resp.status == 200) {
+                log.debug "updated ${resp.data}"
                 def returnStatus = resp.data.status.code
                 if (returnStatus == 0) {
                     log.debug "Successful call to ecobee API."
@@ -889,10 +771,11 @@ private boolean sendCommandToEcobee(Map bodyParams) {
         log.trace "Exception Sending Json: " + e.response.data.status
         debugEvent ("sent Json & got http status ${e.statusCode} - ${e.response.data.status.code}")
         if (e.response.data.status.code == 14) {
-            // TODO - figure out why we're setting the next action to be poll
+            // TODO - figure out why we're setting the next action to be pollChildren
             // after refreshing auth token. Is it to keep UI in sync, or just copy/paste error?
+            atomicState.action = "pollChildren"
             log.debug "Refreshing your auth_token!"
-            refreshAuthToken([async: true, nextAction: "poll"])
+            refreshAuthToken()
         } else {
             debugEvent("Authentication error, invalid authentication method, lack of credentials, etc.")
             log.error "Authentication error, invalid authentication method, lack of credentials, etc."

smartapps/smartthings/gentle-wake-up.src/gentle-wake-up.groovy

@@ -454,17 +454,23 @@ def sendStopEvent(source) {
 		eventData.value += "cancelled"
 	}
 
+	// send 100% completion event
+	sendTimeRemainingEvent(100)
+
+	// send a non-displayed 0% completion to reset tiles
+	sendTimeRemainingEvent(0, false)
+
+	// send sessionStatus event last so the event feed is ordered properly
 	sendControllerEvent(eventData)
-	sendTimeRemainingEvent(0)
 }
 
-def sendTimeRemainingEvent(percentComplete) {
+def sendTimeRemainingEvent(percentComplete, displayed = true) {
 	log.trace "sendTimeRemainingEvent(${percentComplete})"
 
 	def percentCompleteEventData = [
 			name: "percentComplete",
 			value: percentComplete as int,
-			displayed: true,
+			displayed: displayed,
 			isStateChange: true
 	]
 	sendControllerEvent(percentCompleteEventData)
@@ -474,7 +480,7 @@ def sendTimeRemainingEvent(percentComplete) {
 	def timeRemainingEventData = [
 			name: "timeRemaining",
 			value: displayableTime(timeRemaining),
-			displayed: true,
+			displayed: displayed,
 			isStateChange: true
 	]
 	sendControllerEvent(timeRemainingEventData)
@@ -608,8 +614,6 @@ private completion() {
 	handleCompletionMessaging()
 
 	handleCompletionModesAndPhrases()
-
-	sendTimeRemainingEvent(100)
 }
 
 private handleCompletionSwitches() {

smartapps/smartthings/lifx-connect.src/lifx-connect.groovy

@@ -242,8 +242,6 @@ def installed() {
 	} else {
 		initialize()
 	}
-	// Check for new devices and remove old ones every 3 hours
-	runEvery3Hours('updateDevices')
 }
 
 // called after settings are changed
@@ -271,9 +269,19 @@ private removeChildDevices(devices) {
 def initialize() {
 	log.debug "initialize"
 	updateDevices()
+	// Check for new devices and remove old ones every 3 hours
+	runEvery5Minutes('updateDevices')
+	setupDeviceWatch()
 }
 
 // Misc
+private setupDeviceWatch() {
+	def hub = location.hubs[0]
+	// Make sure that all child devices are enrolled in device watch
+	getChildDevices().each {
+		it.sendEvent(name: "DeviceWatch-Enroll", value: "{\"protocol\": \"LAN\", \"scheme\":\"untracked\", \"hubHardwareId\": \"${hub?.hub?.hardwareID}\"}")
+	}
+}
 
 Map apiRequestHeaders() {
 	return ["Authorization": "Bearer ${state.lifxAccessToken}",
@@ -376,7 +384,7 @@ def updateDevices() {
 			def data = [
 					label: device.label,
 					level: Math.round((device.brightness ?: 1) * 100),
-					switch: device.connected ? device.power : "unreachable",
+					switch: device.power,
 					colorTemperature: device.color.kelvin
 			]
 			if (device.product.capabilities.has_color) {
@@ -387,18 +395,42 @@ def updateDevices() {
 			} else {
 				childDevice = addChildDevice(app.namespace, "LIFX White Bulb", device.id, null, data)
 			}
+			childDevice?.completedSetup = true
+		} else {
+			if (device.product.capabilities.has_color) {
+				sendEvent(name: "color", value: colorUtil.hslToHex((device.color.hue / 3.6) as int, (device.color.saturation * 100) as int))
+				sendEvent(name: "hue", value: device.color.hue / 3.6)
+				sendEvent(name: "saturation", value: device.color.saturation * 100)
+			}
+			childDevice.sendEvent(name: "label", value: device.label)
+			childDevice.sendEvent(name: "level", value: Math.round((device.brightness ?: 1) * 100))
+			childDevice.sendEvent(name: "switch.setLevel", value: Math.round((device.brightness ?: 1) * 100))
+			childDevice.sendEvent(name: "switch", value: device.power)
+			childDevice.sendEvent(name: "colorTemperature", value: device.color.kelvin)
+			childDevice.sendEvent(name: "model", value: device.product.name)
 		}
+
+		if (state.devices[device.id] == null) {
+			// State missing, add it and set it to opposite status as current status to provoke event below
+			state.devices[device.id] = [online : !device.connected]
+		}
+
+		if (!state.devices[device.id]?.online && device.connected) {
+			// Device came online after being offline
+			childDevice?.sendEvent(name: "DeviceWatch-DeviceStatus", value: "online", displayed: false)
+			log.debug "$device is back Online"
+		} else if (state.devices[device.id]?.online && !device.connected) {
+			// Device went offline after being online
+			childDevice?.sendEvent(name: "DeviceWatch-DeviceStatus", value: "offline", displayed: false)
+			log.debug "$device went Offline"
+		}
+		state.devices[device.id] = [online: device.connected]
 	}
 	getChildDevices().findAll { !selectors.contains("${it.deviceNetworkId}") }.each {
 		log.info("Deleting ${it.deviceNetworkId}")
+		state.devices[it.deviceNetworkId] = null
 		deleteChildDevice(it.deviceNetworkId)
 	}
-	runIn(1, 'refreshDevices') // Asynchronously refresh devices so we don't block
 }
 
-def refreshDevices() {
-	log.info("Refreshing all devices...")
-	getChildDevices().each { device ->
-		device.refresh()
-	}
-}
+

smartapps/smartthings/logitech-harmony-connect.src/logitech-harmony-connect.groovy

@@ -34,6 +34,7 @@
  *  locks                | lock              | lock, unlock                | locked, unlocked
  *  ---------------------+-------------------+-----------------------------+------------------------------------
  */
+include 'asynchttp_v1'
 
 definition(
     name: "Logitech Harmony (Connect)",
@@ -51,7 +52,7 @@ definition(
 }
 
 preferences(oauthPage: "deviceAuthorization") {
-    page(name: "Credentials", title: "Connect to your Logitech Harmony device", content: "authPage", install: false, nextPage: "deviceAuthorization")
+  page(name: "Credentials", title: "Connect to your Logitech Harmony device", content: "authPage", install: false, nextPage: "deviceAuthorization")
 	page(name: "deviceAuthorization", title: "Logitech Harmony device authorization", install: true) {
 		section("Allow Logitech Harmony to control these things...") {
 			input "switches", "capability.switch", title: "Which Switches?", multiple: true, required: false
@@ -96,38 +97,41 @@ def authPage() {
     def description = null
     if (!state.HarmonyAccessToken) {
 		if (!state.accessToken) {
-			log.debug "About to create access token"
+			log.debug "Harmony - About to create access token"
 			createAccessToken()
 		}
         description = "Click to enter Harmony Credentials"
         def redirectUrl = buildRedirectUrl
         return dynamicPage(name: "Credentials", title: "Harmony", nextPage: null, uninstall: true, install:false) {
-               section { href url:redirectUrl, style:"embedded", required:true, title:"Harmony", description:description }
+            section { paragraph title: "Note:", "This device has not been officially tested and certified to “Work with SmartThings”. You can connect it to your SmartThings home but performance may vary and we will not be able to provide support or assistance." }
+            section { href url:redirectUrl, style:"embedded", required:true, title:"Harmony", description:description }
         }
     } else {
 		//device discovery request every 5 //25 seconds
 		int deviceRefreshCount = !state.deviceRefreshCount ? 0 : state.deviceRefreshCount as int
 		state.deviceRefreshCount = deviceRefreshCount + 1
-		def refreshInterval = 3
+		def refreshInterval = 5
 
 		def huboptions = state.HarmonyHubs ?: []
 		def actoptions = state.HarmonyActivities ?: []
 
 		def numFoundHub = huboptions.size() ?: 0
-        def numFoundAct = actoptions.size() ?: 0
+    def numFoundAct = actoptions.size() ?: 0
+
 		if((deviceRefreshCount % 5) == 0) {
 			discoverDevices()
 		}
+
 		return dynamicPage(name:"Credentials", title:"Discovery Started!", nextPage:"", refreshInterval:refreshInterval, install:true, uninstall: true) {
 			section("Please wait while we discover your Harmony Hubs and Activities. Discovery can take five minutes or more, so sit back and relax! Select your device below once discovered.") {
-				input "selectedhubs", "enum", required:false, title:"Select Harmony Hubs (${numFoundHub} found)", multiple:true, options:huboptions
+				input "selectedhubs", "enum", required:false, title:"Select Harmony Hubs (${numFoundHub} found)", multiple:true, submitOnChange: true, options:huboptions
 			}
-            // Virtual activity flag
-            if (numFoundHub > 0 && numFoundAct > 0 && true)
+      // Virtual activity flag
+      if (numFoundHub > 0 && numFoundAct > 0 && true)
 			section("You can also add activities as virtual switches for other convenient integrations") {
-				input "selectedactivities", "enum", required:false, title:"Select Harmony Activities (${numFoundAct} found)", multiple:true, options:actoptions
+				input "selectedactivities", "enum", required:false, title:"Select Harmony Activities (${numFoundAct} found)", multiple:true, submitOnChange: true, options:actoptions
 			}
-            if (state.resethub)
+    if (state.resethub)
 			section("Connection to the hub timed out. Please restart the hub and try again.") {}
 		}
     }
@@ -137,13 +141,13 @@ def callback() {
 	def redirectUrl = null
 	if (params.authQueryString) {
 		redirectUrl = URLDecoder.decode(params.authQueryString.replaceAll(".+&redirect_url=", ""))
-		log.debug "redirectUrl: ${redirectUrl}"
+		log.debug "Harmony - redirectUrl: ${redirectUrl}"
 	} else {
-		log.warn "No authQueryString"
+		log.warn "Harmony - No authQueryString"
 	}
 
 	if (state.HarmonyAccessToken) {
-		log.debug "Access token already exists"
+		log.debug "Harmony - Access token already exists"
 		discovery()
 		success()
 	} else {
@@ -151,27 +155,27 @@ def callback() {
 		if (code) {
 			if (code.size() > 6) {
 				// Harmony code
-				log.debug "Exchanging code for access token"
+				log.debug "Harmony - Exchanging code for access token"
 				receiveToken(redirectUrl)
 			} else {
 				// Initiate the Harmony OAuth flow.
 				init()
 			}
 		} else {
-			log.debug "This code should be unreachable"
+			log.debug "Harmony - This code should be unreachable"
 			success()
 		}
 	}
 }
 
 def init() {
-	log.debug "Requesting Code"
+	log.debug "Harmony - Requesting Code"
 	def oauthParams = [client_id: "${appSettings.clientId}", scope: "remote", response_type: "code", redirect_uri: "${servercallbackUrl}" ]
 	redirect(location: "https://home.myharmony.com/oauth2/authorize?${toQueryString(oauthParams)}")
 }
 
 def receiveToken(redirectUrl = null) {
-	log.debug "receiveToken"
+	log.debug "Harmony - receiveToken"
     def oauthParams = [ client_id: "${appSettings.clientId}", client_secret: "${appSettings.clientSecret}", grant_type: "authorization_code", code: params.code ]
     def params = [
       uri: "https://home.myharmony.com/oauth2/token?${toQueryString(oauthParams)}",
@@ -182,7 +186,7 @@ def receiveToken(redirectUrl = null) {
         }
 	} catch (java.util.concurrent.TimeoutException e) {
     	fail(e)
-		log.warn "Connection timed out, please try again later."
+		log.warn "Harmony - Connection timed out, please try again later."
 	}
     discovery()
 	if (state.HarmonyAccessToken) {
@@ -306,7 +310,7 @@ def buildRedirectUrl(page) {
 
 def installed() {
 	if (!state.accessToken) {
-		log.debug "About to create access token"
+		log.debug "Harmony - About to create access token"
 		createAccessToken()
 	} else {
 		initialize()
@@ -314,10 +318,8 @@ def installed() {
 }
 
 def updated() {
-	unsubscribe()
-  unschedule()
 	if (!state.accessToken) {
-		log.debug "About to create access token"
+		log.debug "Harmony - About to create access token"
 		createAccessToken()
 	} else {
 		initialize()
@@ -328,9 +330,9 @@ def uninstalled() {
 	if (state.HarmonyAccessToken) {
 		try {
         	state.HarmonyAccessToken = ""
-        	log.debug "Success disconnecting Harmony from SmartThings"
+        	log.debug "Harmony - Success disconnecting Harmony from SmartThings"
 		} catch (groovyx.net.http.HttpResponseException e) {
-			log.error "Error disconnecting Harmony from SmartThings: ${e.statusCode}"
+			log.error "Harmony - Error disconnecting Harmony from SmartThings: ${e.statusCode}"
 		}
 	}
 }
@@ -339,7 +341,8 @@ def initialize() {
 	state.aux = 0
 	if (selectedhubs || selectedactivities) {
 		addDevice()
-        runEvery5Minutes("poll")
+    runEvery5Minutes("poll")
+    getActivityList()
 	}
 }
 
@@ -348,7 +351,7 @@ def getHarmonydevices() {
 }
 
 Map discoverDevices() {
-    log.trace "Discovering devices..."
+    log.trace "Harmony - Discovering devices..."
     discovery()
     if (getHarmonydevices() != []) {
         def devices = state.Harmonydevices.hubs
@@ -360,7 +363,7 @@ Map discoverDevices() {
             def hubname = getHubName(it.key)
             def hubvalue = "${hubname}"
             hubs["harmony-${hubkey}"] = hubvalue
-        	it.value.response.data.activities.each {
+        	  it.value.response.data.activities.each {
                 def value = "${it.value.name}"
                 def key = "harmony-${hubkey}-${it.key}"
                 activities["${key}"] = value
@@ -378,164 +381,177 @@ def discovery() {
 	try {
 		httpGet(uri: url, headers: ["Accept": "application/json"]) {response ->
 	    	if (response.status == 200) {
-            	log.debug "valid Token"
+            	log.debug "Harmony - valid Token"
                 state.Harmonydevices = response.data
                 state.resethub = false
-                getActivityList()
-                poll()
 	        } else {
-            	log.debug "Error: $response.status"
+            	log.debug "Harmony - Error: $response.status"
             }
 	    }
 	} catch (groovyx.net.http.HttpResponseException e) {
         if (e.statusCode == 401) { // token is expired
             state.remove("HarmonyAccessToken")
-            log.warn "Harmony Access token has expired"
+            log.warn "Harmony - Harmony Access token has expired"
         }
 	} catch (java.net.SocketTimeoutException e) {
-		log.warn "Connection to the hub timed out. Please restart the hub and try again."
+		log.warn "Harmony - Connection to the hub timed out. Please restart the hub and try again."
     state.resethub = true
  	} catch (e) {
-    log.info "Logitech Harmony - Error: $e"
+    log.info "Harmony - Error: $e"
 	}
     return null
 }
 
 def addDevice() {
-    log.trace "Adding Hubs"
+    log.trace "Harmony - Adding Hubs"
     selectedhubs.each { dni ->
         def d = getChildDevice(dni)
         if(!d) {
             def newAction = state.HarmonyHubs.find { it.key == dni }
             d = addChildDevice("smartthings", "Logitech Harmony Hub C2C", dni, null, [label:"${newAction.value}"])
-            log.trace "created ${d.displayName} with id $dni"
+            log.trace "Harmony - Created ${d.displayName} with id $dni"
             poll()
         } else {
-            log.trace "found ${d.displayName} with id $dni already exists"
+            log.trace "Harmony - Found ${d.displayName} with id $dni already exists"
         }
     }
-    log.trace "Adding Activities"
+    log.trace "Harmony - Adding Activities"
     selectedactivities.each { dni ->
         def d = getChildDevice(dni)
         if(!d) {
             def newAction = state.HarmonyActivities.find { it.key == dni }
             if (newAction) {
 	            d = addChildDevice("smartthings", "Harmony Activity", dni, null, [label:"${newAction.value} [Harmony Activity]"])
-	            log.trace "created ${d.displayName} with id $dni"
+	            log.trace "Harmony - Created ${d.displayName} with id $dni"
 	            poll()
             }
         } else {
-            log.trace "found ${d.displayName} with id $dni already exists"
+            log.trace "Harmony - Found ${d.displayName} with id $dni already exists"
         }
     }
 }
 
 def activity(dni,mode) {
-    def Params = [auth: state.HarmonyAccessToken]
-    def msg = "Command failed"
-    def url = ''
+    def tokenParam = [auth: state.HarmonyAccessToken]
+    def url
     if (dni == "all") {
-        url = "https://home.myharmony.com/cloudapi/activity/off?${toQueryString(Params)}"
+        url = "https://home.myharmony.com/cloudapi/activity/off?${toQueryString(tokenParam)}"
     } else {
         def aux = dni.split('-')
         def hubId = aux[1]
         if (mode == "hub" || (aux.size() <= 2) || (aux[2] == "off")){
-        	url = "https://home.myharmony.com/cloudapi/hub/${hubId}/activity/off?${toQueryString(Params)}"
+        	url = "https://home.myharmony.com/cloudapi/hub/${hubId}/activity/off?${toQueryString(tokenParam)}"
         } else {
-            def activityId = aux[2]
-        	url = "https://home.myharmony.com/cloudapi/hub/${hubId}/activity/${activityId}/${mode}?${toQueryString(Params)}"
+          def activityId = aux[2]
+        	url = "https://home.myharmony.com/cloudapi/hub/${hubId}/activity/${activityId}/${mode}?${toQueryString(tokenParam)}"
         }
 	}
-	try {
-    	httpPostJson(uri: url) { response ->
-        	if (response.data.code == 200 || dni == "all") {
-            	msg = "Command sent succesfully"
-            	state.aux = 0
-            } else {
-            	msg = "Command failed. Error: $response.data.code"
-            }
-		}
-    } catch (groovyx.net.http.HttpResponseException ex) {
-        log.error ex
-        if (state.aux == 0) {
-        	state.aux = 1
-        	activity(dni,mode)
-        } else {
-        	msg = ex
-            state.aux = 0
-        }
-    } catch(Exception ex) {
-    	msg = ex
+  def params = [
+      uri: url,
+      contentType: 'application/json'
+  ]
+  asynchttp_v1.post('activityResponse', params)
+  return "Command Sent"
+}
+
+def activityResponse(response, data) {
+  if (response.hasError()) {
+    log.error "Harmony - response has error: $response.errorMessage"
+    if (response.status == 401) { // token is expired
+      state.remove("HarmonyAccessToken")
+      log.warn "Harmony - Access token has expired"
     }
-    runIn(10, "poll", [overwrite: true])
-    return msg
+  } else {
+    if (response.status == 200) {
+      log.trace "Harmony - Command sent succesfully"
+      poll()
+    } else {
+      log.trace "Harmony - Command failed. Error: $response.status"
+    }
+  }
 }
 
 def poll() {
 	// GET THE LIST OF ACTIVITIES
     if (state.HarmonyAccessToken) {
-    	  getActivityList()
-        def Params = [auth: state.HarmonyAccessToken]
-        def url = "https://home.myharmony.com/cloudapi/state?${toQueryString(Params)}"
-        try {
-            httpGet(uri: url, headers: ["Accept": "application/json"]) {response ->
-                def map = [:]
-                response.data.hubs.each {
-		            if (it.value.message == "OK") {
-	                    map["${it.key}"] = "${it.value.response.data.currentAvActivity},${it.value.response.data.activityStatus}"
-	                    def hub = getChildDevice("harmony-${it.key}")
-	                    if (hub) {
-	                        if (it.value.response.data.currentAvActivity == "-1") {
-	                            hub.sendEvent(name: "currentActivity", value: "--", descriptionText: "There isn't any activity running", display: false)
-	                        } else {
-	                            def currentActivity = getActivityName(it.value.response.data.currentAvActivity,it.key)
-	                            hub.sendEvent(name: "currentActivity", value: currentActivity, descriptionText: "Current activity is ${currentActivity}", display: false)
-	                        }
-	                    }
-	                } else {
-		                log.trace it.value.message
-	                }
-                }
-                def activities = getChildDevices()
-                def activitynotrunning = true
-                activities.each { activity ->
-                    def act = activity.deviceNetworkId.split('-')
-                    if (act.size() > 2) {
-                        def aux = map.find { it.key == act[1] }
-                        if (aux) {
-                            def aux2 = aux.value.split(',')
-                            def childDevice = getChildDevice(activity.deviceNetworkId)
-                            if ((act[2] == aux2[0]) && (aux2[1] == "1" || aux2[1] == "2")) {
-                                childDevice?.sendEvent(name: "switch", value: "on")
-                                if (aux2[1] == "1")
-                                    runIn(5, "poll", [overwrite: true])
-                            } else {
-                                childDevice?.sendEvent(name: "switch", value: "off")
-                                if (aux2[1] == "3")
-                                    runIn(5, "poll", [overwrite: true])
-                            }
-                        }
-                    }
-                }
-                return "Poll completed $map - $state.hubs"
-            }
-        } catch (groovyx.net.http.HttpResponseException e) {
-              if (e.statusCode == 401) { // token is expired
-                  state.remove("HarmonyAccessToken")
-                  log.warn "Harmony Access token has expired"
-              }
-        } catch (java.net.SocketTimeoutException e) {
-        	log.warn "Connection to the hub timed out. Please restart the hub and try again."
-              state.resethub = true
-        } catch (e) {
-        	log.info "Logitech Harmony - Error: $e"
-        }
-    }
+        def tokenParam = [auth: state.HarmonyAccessToken]
+        def params = [
+            uri: "https://home.myharmony.com/cloudapi/state?${toQueryString(tokenParam)}",
+            headers: ["Accept": "application/json"],
+            contentType: 'application/json'
+        ]
+        asynchttp_v1.get('pollResponse', params)
+      } else {
+        log.warn "Harmony - Access token has expired"
+      }
 }
 
+def pollResponse(response, data) {
+	if (response.hasError()) {
+    log.error "Harmony - response has error: $response.errorMessage"
+    if (response.status == 401) { // token is expired
+      state.remove("HarmonyAccessToken")
+      log.warn "Harmony - Access token has expired"
+    }
+	} else {
+			def ResponseValues
+			try {
+					// json response already parsed into JSONElement object
+					ResponseValues = response.json
+			} catch (e) {
+					log.error "Harmony - error parsing json from response: $e"
+			}
+			if (ResponseValues) {
+        def map = [:]
+        ResponseValues.hubs.each {
+        if (it.value.message == "OK") {
+              map["${it.key}"] = "${it.value.response.data.currentAvActivity},${it.value.response.data.activityStatus}"
+              def hub = getChildDevice("harmony-${it.key}")
+              if (hub) {
+                  if (it.value.response.data.currentAvActivity == "-1") {
+                      hub.sendEvent(name: "currentActivity", value: "--", descriptionText: "There isn't any activity running", display: false)
+                  } else {
+                      def currentActivity
+                      def activityDTH = getChildDevice("harmony-${it.key}-${it.value.response.data.currentAvActivity}")
+                      if (activityDTH)
+                        currentActivity = activityDTH.device.displayName
+                      else
+                        currentActivity = getActivityName(it.value.response.data.currentAvActivity,it.key)
+                      hub.sendEvent(name: "currentActivity", value: currentActivity, descriptionText: "Current activity is ${currentActivity}", display: false)
+                  }
+              }
+          } else {
+            log.trace "Harmony - error response: $it.value.message"
+          }
+        }
+        def activities = getChildDevices()
+        def activitynotrunning = true
+        activities.each { activity ->
+            def act = activity.deviceNetworkId.split('-')
+            if (act.size() > 2) {
+                def aux = map.find { it.key == act[1] }
+                if (aux) {
+                    def aux2 = aux.value.split(',')
+                    def childDevice = getChildDevice(activity.deviceNetworkId)
+                    if ((act[2] == aux2[0]) && (aux2[1] == "1" || aux2[1] == "2")) {
+                        childDevice?.sendEvent(name: "switch", value: "on")
+                        if (aux2[1] == "1")
+                            runIn(5, "poll", [overwrite: true])
+                    } else {
+                        childDevice?.sendEvent(name: "switch", value: "off")
+                        if (aux2[1] == "3")
+                            runIn(5, "poll", [overwrite: true])
+                    }
+                }
+            }
+        }
+			} else {
+					log.debug "Harmony - did not get json results from response body: $response.data"
+			}
+	}
+}
 
 def getActivityList() {
-	// GET ACTIVITY'S NAME
     if (state.HarmonyAccessToken) {
         def Params = [auth: state.HarmonyAccessToken]
         def url = "https://home.myharmony.com/cloudapi/activity/all?${toQueryString(Params)}"
@@ -552,21 +568,19 @@ def getActivityList() {
                                 [id: it.key, name: it.value['name'], type: it.value['type']]
                             }
                             activities += [id: "off", name: "Activity OFF", type: "0"]
-                            log.trace activities
                         }
                         hub.sendEvent(name: "activities", value: new groovy.json.JsonBuilder(activities).toString(), descriptionText: "Activities are ${activities.collect { it.name }?.join(', ')}", display: false)
-					}
+					          }
                 }
             }
         } catch (groovyx.net.http.HttpResponseException e) {
         	log.trace e
         } catch (java.net.SocketTimeoutException e) {
         	log.trace e
-		} catch(Exception e) {
+		    } catch(Exception e) {
         	log.trace e
-		}
+		    }
     }
-	return activity
 }
 
 def getActivityName(activity,hubId) {
@@ -629,7 +643,7 @@ def sendNotification(msg) {
 
 def hookEventHandler() {
     // log.debug "In hookEventHandler method."
-    log.debug "request = ${request}"
+    log.debug "Harmony - request = ${request}"
 
     def json = request.JSON
 
@@ -638,14 +652,14 @@ def hookEventHandler() {
 }
 
 def listDevices() {
-	log.debug "getDevices, params: ${params}"
+	log.debug "Harmony - getDevices(), params: ${params}"
 	allDevices.collect {
 		deviceItem(it)
 	}
 }
 
 def getDevice() {
-	log.debug "getDevice, params: ${params}"
+	log.debug "Harmony - getDevice(), params: ${params}"
 	def device = allDevices.find { it.id == params.id }
 	if (!device) {
 		render status: 404, data: '{"msg": "Device not found"}'
@@ -658,7 +672,7 @@ def updateDevice() {
 	def data = request.JSON
 	def command = data.command
 	def arguments = data.arguments
-	log.debug "updateDevice, params: ${params}, request: ${data}"
+	log.debug "Harmony - updateDevice(), params: ${params}, request: ${data}"
 	if (!command) {
 		render status: 400, data: '{"msg": "command is required"}'
 	} else {
@@ -726,7 +740,7 @@ def getDeviceCapabilityCommands(deviceCapabilities) {
 }
 
 def listSubscriptions() {
-	log.debug "listSubscriptions()"
+	log.debug "Harmony - listSubscriptions()"
 	app.subscriptions?.findAll { it.device?.device && it.device.id }?.collect {
 		def deviceInfo = state[it.device.id]
 		def response = [
@@ -747,17 +761,17 @@ def addSubscription() {
 	def attribute = data.attributeName
 	def callbackUrl = data.callbackUrl
 
-	log.debug "addSubscription, params: ${params}, request: ${data}"
+	log.debug "Harmony - addSubscription, params: ${params}, request: ${data}"
 	if (!attribute) {
 		render status: 400, data: '{"msg": "attributeName is required"}'
 	} else {
 		def device = allDevices.find { it.id == data.deviceId }
 		if (device) {
 			if (!state.harmonyHubs) {
-				log.debug "Adding callbackUrl: $callbackUrl"
+				log.debug "Harmony - Adding callbackUrl: $callbackUrl"
 				state[device.id] = [callbackUrl: callbackUrl]
 			}
-			log.debug "Adding subscription"
+			log.debug "Harmony - Adding subscription"
 			def subscription = subscribe(device, attribute, deviceHandler)
 			if (!subscription || !subscription.eventSubscription) {
 				subscription = app.subscriptions?.find { it.device?.device && it.device.id == data.deviceId && it.data == attribute && it.handler == 'deviceHandler' }
@@ -785,7 +799,7 @@ def removeSubscription() {
 
 	log.debug "removeSubscription, params: ${params}, subscription: ${subscription}, device: ${device}"
 	if (device) {
-		log.debug "Removing subscription for device: ${device.id}"
+		log.debug "Harmony - Removing subscription for device: ${device.id}"
 		state.remove(device.id)
 		unsubscribe(device)
 	}
@@ -809,16 +823,17 @@ def deviceHandler(evt) {
 	def deviceInfo = state[evt.deviceId]
 	if (state.harmonyHubs) {
 		state.harmonyHubs.each { harmonyHub ->
+      log.trace "Harmony - Sending data to $harmonyHub.name"
 			sendToHarmony(evt, harmonyHub.callbackUrl)
 		}
 	} else if (deviceInfo) {
 		if (deviceInfo.callbackUrl) {
 			sendToHarmony(evt, deviceInfo.callbackUrl)
 		} else {
-			log.warn "No callbackUrl set for device: ${evt.deviceId}"
+			log.warn "Harmony - No callbackUrl set for device: ${evt.deviceId}"
 		}
 	} else {
-		log.warn "No subscribed device found for device: ${evt.deviceId}"
+		log.warn "Harmony - No subscribed device found for device: ${evt.deviceId}"
 	}
 }
 
@@ -842,12 +857,12 @@ def sendToHarmony(evt, String callbackUrl) {
       body: [evt: [deviceId: evt.deviceId, name: evt.name, value: evt.value]]
     ]
     try {
-        log.debug "Sending data to Harmony Cloud: $params"
+        log.debug "Harmony - Sending data to Harmony Cloud: $params"
         httpPostJson(params) { resp ->
-            log.debug "Harmony Cloud - Response: ${resp.status}"
+            log.debug "Harmony - Cloud Response: ${resp.status}"
         }
     } catch (e) {
-        log.error "Harmony Cloud - Something went wrong: $e"
+        log.error "Harmony - Cloud Something went wrong: $e"
     }
   }
 }
@@ -872,10 +887,10 @@ def activityCallback() {
 		if (data.errorCode == "200") {
 			device.setCurrentActivity(data.currentActivityId)
 		} else {
-			log.warn "Activity callback error: ${data}"
+			log.warn "Harmony - Activity callback error: ${data}"
 		}
 	} else {
-		log.warn "Activity callback sent to non-existant dni: ${params.dni}"
+		log.warn "Harmony - Activity callback sent to non-existant dni: ${params.dni}"
 	}
 	render status: 200, data: '{"msg": "Successfully received callbackUrl"}'
 }
@@ -909,13 +924,13 @@ def harmony() {
 }
 
 def deleteHarmony() {
-	log.debug "Trying to delete Harmony hub with mac: ${params.mac}"
+	log.debug "Harmony - Trying to delete Harmony hub with mac: ${params.mac}"
 	def harmonyHub = state.harmonyHubs?.find { it.mac == params.mac }
 	if (harmonyHub) {
-		log.debug "Deleting Harmony hub with mac: ${params.mac}"
+		log.debug "Harmony - Deleting Harmony hub with mac: ${params.mac}"
 		state.harmonyHubs.remove(harmonyHub)
 	} else {
-		log.debug "Couldn't find Harmony hub with mac: ${params.mac}"
+		log.debug "Harmony - Couldn't find Harmony hub with mac: ${params.mac}"
 	}
 	render status: 204, data: "{}"
 }

smartapps/smartthings/severe-weather-alert.src/severe-weather-alert.groovy

@@ -26,17 +26,22 @@ definition(
 )
 
 preferences {
-	section ("In addition to push notifications, send text alerts to...") {
-        input("recipients", "contact", title: "Send notifications to") {
-            input "phone1", "phone", title: "Phone Number 1", required: false
-            input "phone2", "phone", title: "Phone Number 2", required: false
-            input "phone3", "phone", title: "Phone Number 3", required: false
-        }
+
+  if (!(location.zipCode || ( location.latitude && location.longitude )) && location.channelName == 'samsungtv') {
+		section { paragraph title: "Note:", "Location is required for this SmartApp. Go to 'Location Name' settings to setup your correct location." }
 	}
 
-	section ("Zip code (optional, defaults to location coordinates)...") {
-		input "zipcode", "text", title: "Zip Code", required: false
-	}
+  if (location.channelName != 'samsungtv') {
+		section( "Set your location" ) { input "zipCode", "text", title: "Zip code" }
+  }
+
+	section ("In addition to push notifications, send text alerts to...") {
+      input("recipients", "contact", title: "Send notifications to") {
+          input "phone1", "phone", title: "Phone Number 1", required: false
+          input "phone2", "phone", title: "Phone Number 2", required: false
+          input "phone3", "phone", title: "Phone Number 3", required: false
+      }
+	 }
 }
 
 def installed() {
@@ -61,7 +66,7 @@ def checkForSevereWeather() {
 	def alerts
 	if(locationIsDefined()) {
 		if(zipcodeIsValid()) {
-			alerts = getWeatherFeature("alerts", zipcode)?.alerts
+			alerts = getWeatherFeature("alerts", zipCode)?.alerts
 		} else {
 			log.warn "Severe Weather Alert: Invalid zipcode entered, defaulting to location's zipcode"
 			alerts = getWeatherFeature("alerts")?.alerts

smartapps/smartthings/wemo-connect.src/wemo-connect.groovy

@@ -86,6 +86,7 @@ def firstPage()
 		def lightSwitchesDiscovered = lightSwitchesDiscovered()
 
 		return dynamicPage(name:"firstPage", title:"Discovery Started!", nextPage:"", refreshInterval: refreshInterval, install:true, uninstall: true) {
+			section { paragraph title: "Note:", "This device has not been officially tested and certified to “Work with SmartThings”. You can connect it to your SmartThings home but performance may vary and we will not be able to provide support or assistance." }
 			section("Select a device...") {
 				input "selectedSwitches", "enum", required:false, title:"Select Wemo Switches \n(${switchesDiscovered.size() ?: 0} found)", multiple:true, options:switchesDiscovered
 				input "selectedMotions", "enum", required:false, title:"Select Wemo Motions \n(${motionsDiscovered.size() ?: 0} found)", multiple:true, options:motionsDiscovered
@@ -681,4 +682,4 @@ private Boolean hasAllHubsOver(String desiredFirmware) {
 
 private List getRealHubFirmwareVersions() {
 	return location.hubs*.firmwareVersionString.findAll { it }
-}
+}